Prg486jdg/03 Parts

This OEM replacement part is a motor assembly for ovens. The motor assembly is the main motor that powers the oven fan which is responsible for maintaining and adjusting the temperature in an oven. If the oven is no longer heating properly, turning on, or maintaining temperature, then the motor assembly will need to be replaced.To replace this part, make sure that the oven is unplugged. After it has been powered off, proceed to pull the oven out and away from the wall. Once moved, uninstall the back panel of the oven by removing the panel's mounting screws. After detaching the back panel, locate the motor housing on the back of the oven. Unthread the screws that hold the housing in place. Once removed, locate the mounting brackets that hold the motor in place and remove the screws that attach to the motor. Pull the old motor out of its place and install the new motor. Reinstall the back panel and restore power to the appliance.This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador brand ovens.

This pilot light lens covers and diffuses the control-panel indicator lamp. Replace a cracked, missing, or discolored lens to restore clear visibility of the light, protect the lamp opening, and keep the panel looking finished.

• Covers and diffuses the indicator lamp on the control panel
• Helps protect the lamp opening from debris and accidental contact
• Restores a clean, finished appearance to the panel
• Replace if the lens is cracked, missing, loose, or discolored
• Can help when the indicator is hard to see even when lit

• Disconnect power to the appliance before servicing and allow surfaces to cool
• Access the indicator opening from the front or rear (varies by design) and remove any retainer or clips holding the old lens
• Note orientation and transfer any existing retainer or gasket if present
• Seat the new lens fully, reassemble, and test the indicator light

Oven not reaching set temperature or baking unevenly? This mechanical thermostat senses cavity temp and cycles heat to maintain consistent cooking results.

This rotary potentiometer converts shaft rotation into an electrical signal the control board can read, providing precise position feedback for user selections. Replace it if inputs become erratic, jump between settings, or the control stops responding.

• Provides rotary position feedback to the electronic control
• Enables accurate selection and adjustment of functions or setpoints
• Wear or damage can cause drifting, dead spots, or incorrect readings
• Intermittent or no response to input is a common failure symptom

• Disconnect power before servicing
• Access the control/console area to reach the component
• Note shaft orientation and any connector positions; transfer exactly to the new part
• Handle electronics with ESD care and verify smooth, full-range operation after reassembly

Fixes no spark at burners or oven not lighting issues. This ignition module generates the high-voltage spark needed to ignite gas at electrodes.

Fix a squealing or non-working oven fan with this gas range blower fan motor. Restores even heat distribution during baking and broiling cycles.

Fix an oven light that won't turn on or a self-clean cycle that won't start. This door switch monitors door position for safety and lighting.

If your gas burner won't ignite or clicks continuously without lighting, the spark module may have failed. This electronic component generates sparks reliably.

Replace a seized or corroded burner gas tube when igniters stop working or burners won't light. Delivers gas safely to surface burners. DIY repair.

Stabilizing leveling foot for gas ranges. Provides balance and proper elevation. Replace if worn, broken, or missing to restore stability and positioning.

This is an indicator light or display component mounted on the range's control panel that provides visual feedback about oven or burner status. It lets you know when a heating element is active or when the oven has reached the set temperature. Replace this part if the indicator fails to illuminate, flickers intermittently, or displays incorrect information.

Fix overheating or loud fan noise in your gas range with this cooling fan motor. Protects electronics by circulating air to cool internal components.

Restore oven visibility with this complete light assembly. Replace when bulb won't light, lens is cracked, or socket is damaged. Verify fit with your model.

Oven or burner won't adjust temperature correctly? This range potentiometer restores variable control. DIY-friendly repair, takes about 20 minutes.

Replacement oven rack for gas ranges. Heavy-duty metal construction with powder-coated finish. Needed when original rack is warped, damaged, or missing.

Support, hinge counter restores proper hinge support and door balance for a worn or damaged hinge assembly. This replacement helps the appliance door open and close smoothly and stay aligned for reliable everyday use. What it does:

• Provides structural support to the door hinge and helps counterbalance the door
• Stabilizes hinge movement to reduce sagging, binding, or uneven closing
• Helps the door latch and seal correctly by keeping the hinge alignment consistent
• Use when you notice door droop, difficulty latching, or irregular door motion

• Installation may require partial disassembly of the door or hinge assembly—refer to the OEM instructions for your model
• Disconnect power and turn off water supply before beginning any repair
• Inspect surrounding hinge components and fasteners; replace any damaged parts and test door operation after installation