Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replacement mounting screw for refrigerator panels, brackets, door handles, and trim. Needed when original hardware is missing, stripped, or corroded.
Black bottom door hinge and pin assembly for side-by-side refrigerators. Replace this load-bearing pivot component if cracked, broken, or worn out.
I replaced the lever asm. and spring Read more
Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.
Replaced the water tank. Followed the video instruction provided by Appliance Parts Pros. Very good instruction. Read more
Secures the evaporator fan shroud to the rear compartment frame. Replace if rusted, cracked, or broken to properly support the fan assembly and alignment.
I replaced the Evaporator Fan Motor the brackets were rusty so I ordered them. Read more
Internal water reservoir with attached tubing that stores and delivers chilled water to the dispenser. Replace if cracked, leaking, or damaged.
Installing the tank went quickly. Removed the water filter from the upper compartment to stop water flow to the tank. Had to remove the two lower drawers (they tilt out of their sliding frames). There is a glass shelf that should be pulled out - it slides out via two notches in the front frame. The water tank is behind a white metal cover held by 4 screws. Keep track of all of the parts including the lip seals from the shelf. I used two Watts 5/15x5/16 couplers from Lowes for the connections.... Read more
Fix loud tapping or knocking noises and uneven cooling in your fridge. This air damper restores balanced temperature control. DIY repair in about 1 hour.
All my reading online pointed to the damper doors, and by standing in the open door of my fridge, I patiently waited until it happened again, and determined it was the ones behind the crisper. Problem was, there's both a single unit and a double set of doors listed on your part list. I decided to order both sets (and they came in two days, thank you). I watched your great video and even though my unit didn't perfectly match the one you demonstrated, it was close enough that I made the repair... Read more
Size: 10-32 GXTT FLP.595 S
Great site to DIY! Purchased fresh produce drawer railing and parts. Fixed in under 10 minutes. Thanks so much! Read more
Ice maker not filling or water spilling? This fill cup directs water into the ice maker mold for proper ice production. Simple clip-on install.
Went online to appliance pro, found my model and the ice maker part number. The process was very easily. The order process was also very simple and the part was delivered promptly with installation instructions. Read more
Bottom hinge that supports the refrigerator door weight and serves as the pivot point. Replace if worn, cracked, or causing door misalignment and sagging.
Replaced the hinges and all parts pertaining to hinges on the refrigerator door. Total cost was approx. $83 and it took 1 hour this morning (Saturday). Now the door is closing tightly. The refrigerator is 10 years old. GE brand. Read more
Front mounting grommet for refrigerator ice makers. Secures ice maker assembly to freezer wall. Replace if cracked, missing, or worn to restore stability.
Replaced the housing the water filter screws into. Water works fine now. Read more
Donut-shaped gasket creates a tight seal between refrigerator components. Replace when worn to stop minor leaks and restore secure fit. Verify fit with your model number.
Secures the evaporator fan assembly behind the rear freezer panel. Replace if cracked, rusted, or missing to restore proper fan mounting and clearance.
The problem was most likely the evaporator fan motor but it could have been a bad blade, loose parts or bad motor mounts. Hard to tell without taking everything apart and inspecting. Since fridge was 17 years old I decided to order the entire evaporator fan assembly as shown in the parts diagram including fan blade, motor brackets, motor, motor mounts, screws, etc. Getting to the assembly involved removing the ice maker unit plus the entire rear inside of the freezer section. Parts cost around... Read more
Replace your worn or broken refrigerator bottom hinge pin. Supports the door and serves as the lower pivot point on the bottom hinge assembly.
White
Replaced dispenser kit and auger. Repair videos were a great help and resolved potential problems that I usually solved by trial and error. Thanks, Appliance Part Pros! Read more
The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the system. It helps maintain the purity and effectiveness of the refrigerant as it cycles through the system.
You should replace the R134 drier if it becomes clogged or damaged. Common causes of a bad drier include wear and tear over time, exposure to moisture, or contamination from other failing components in the refrigeration system.
Symptoms of a bad R134 drier include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.