Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Slide Rail is an OEM part for GE refrigerators. It is designed to support and guide the movement of drawers and shelves within the refrigerator, ensuring smooth and effortless access to stored items. The slide measures approximately 7 inches. This assembly contains 2 slides
Over time, slide rails can become worn out or damaged due to frequent use, exposure to heavy loads, or accidental mishandling.
Symptoms of a bad slide rail include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
First I had to remove the right glide that had 2 screws. with a T-20 star bit. Then I did the same to the left glide . replacing both glides I just reversed the process. Read more
Stores ice in the freezer and drives it to the dispenser chute. Replace this assembly when the bucket is cracked, the auger is worn, or ice won't dispense.
Replace ice bucket...threw old one away. Read more
I looked for a site that sold replacement parts for my make of GE refrigerator. I found AppliancePartsPros, and was very surprised at how organized it was. By entering the model number of my refrigerator, I was shown a set of (approximately) 8 general parts diagrams for my refrigerator. I chose the ice making/dispensing diagram. I matched the part that shattered (from use) to what was on the diagram. What I didn't know was how to install the part. I saw references by other customer comments to... Read more
Lamp 40w chill
Changed cover / evaporator unit (could have salvaged the old one but it had a lot of black mold and not worth effort. Replaced drip pan (Note: going forward I will do preventive maintenance and replace this every 3-4 years whether it needs it or not) Took apart other parts with mold and cleaned/replaced Read more
Under five minutes. Remove old shield and replace with new. Read more
Replaced motor and solenoid cube along with dispenser auger. Simply watched video on repair and installation and really had no problem. My refrigerator is so old that one of the holes in the motor did not align properly. Had to drill another hole to mount the motor to the housing, took ten minutes. The ice auger took the longest as I was afraid of breaking the plastic housing trying to get the tabs to release. Had to watch the video twice to make sure I got the blades back in the right order.... Read more
I checked your video online and found that it did not apply to my refrigerator, a GE Profile model. I wasn't sure if I needed to remove the bracket/escutcheon or not. The repair proved to be much easier once I removed the control panel (after first turning off the power), unclipped the wire harnesses, removed four screws holding the assembly and then took out the assembly. It took some time to determine how to remove the old assembly and insert the new one without damaging the new one. A... Read more
Swapped it out for new tube. Take 5 minutes and zero effort. The drain tube will clog with mold. You can clean it out but the tube will clog again despite's you best efforts as the tube wall provide a great habitat. Ordered new tubes to facilitate swap-outs. Old tubes can be cleaned but will recolonize quickly. Read more
Compressor overload switch broke in my hand when I removed it but replacing it and the start relay did not fix the problem. I troubleshot the control board with the help of videos from Grace Appliance (https://www.youtube.com/c/GraceAppliance/videos) and found fans were not getting power. I ordered an aftermarket control board that offered free returns but it kept cycling off and on every minute. I think it might have been overloaded because the main resistor in the evaporator fan drive... Read more
Replaced Damper. The iron gasket was sent the I ordered the damper Read more
This is the top light shield for the refrigerator interior that protects the light assembly and helps direct illumination across the compartment. Replaces a cracked or missing shield to restore proper light coverage and appearance. What it does:
What's included:
Install notes:
Bisque
This white toe kick plate covers the bottom front of your refrigerator, concealing the condenser coils and providing a finished appearance. It snaps into place at floor level and protects the mechanical components underneath from dust and damage. Replace this grille if it's cracked, discolored, or missing, as proper ventilation is essential for refrigerator efficiency.
Part arrived promptly and was installed within 5 minutes with a screwdriver. Thanks Read more
Used in the crisper to help keep things fresh. 2 pack.