Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix a warm Custom Cool drawer or knocking noise from the bottom compartment. This fan assembly restores proper airflow for faster chilling. DIY repair.
I replaced the fan and heater element. The replacement was not an exact match. I had to adjust the parts to get the harness to fit the plug was not the correct size. I cut it off and used the existing plug. Not a big deal and everything else fit. Pretty good for a twenty year old replacement. Also the heater element was a different shape but it fit as is. Read more
Ice maker not filling or water dispenser leaking? This water inlet valve controls flow to your ice maker and dispenser. Most DIYers complete in 15-30 minutes.
I researched the problem online and determined it was undoubtedly the water valve leaking. A visit to AppliancePartsPros.com to order the replacement valve and I was ready to go. Actual repair only took 15 minutes. Read more
Base grille kickplate mounts across the lower front of your refrigerator, covering the condenser area. Replace if cracked, broken, or missing.
Ordered part and installed in about 2 minutes. Read more
Internal water reservoir with attached tubing that stores and delivers chilled water to the dispenser. Replace if cracked, leaking, or damaged.
Installing the tank went quickly. Removed the water filter from the upper compartment to stop water flow to the tank. Had to remove the two lower drawers (they tilt out of their sliding frames). There is a glass shelf that should be pulled out - it slides out via two notches in the front frame. The water tank is behind a white metal cover held by 4 screws. Keep track of all of the parts including the lip seals from the shelf. I used two Watts 5/15x5/16 couplers from Lowes for the connections.... Read more
Size: 10-32 GXTT FLP.595 S
Great site to DIY! Purchased fresh produce drawer railing and parts. Fixed in under 10 minutes. Thanks so much! Read more
Fix loud tapping or knocking noises and uneven cooling in your fridge. This air damper restores balanced temperature control. DIY repair in about 1 hour.
All my reading online pointed to the damper doors, and by standing in the open door of my fridge, I patiently waited until it happened again, and determined it was the ones behind the crisper. Problem was, there's both a single unit and a double set of doors listed on your part list. I decided to order both sets (and they came in two days, thank you). I watched your great video and even though my unit didn't perfectly match the one you demonstrated, it was close enough that I made the repair... Read more
Front mounting grommet for refrigerator ice makers. Secures ice maker assembly to freezer wall. Replace if cracked, missing, or worn to restore stability.
Replaced the housing the water filter screws into. Water works fine now. Read more
This is a refrigerator ice and water dispenser drip tray located on the freezer door. Color: White. It measures about 8 inches wide by 4 inches deep. For black order WR17X11655.
Ordered the new interface display - this must be the easiest refrigerator repair possible. My version popped right off without even a screw (some models have a screw). There are 3 different sizes of connector to disconnect and hook up to the new board - so you really can't mess that up. Read more
Secures the evaporator fan shroud to the rear compartment frame. Replace if rusted, cracked, or broken to properly support the fan assembly and alignment.
The problem was most likely the evaporator fan motor but it could have been a bad blade, loose parts or bad motor mounts. Hard to tell without taking everything apart and inspecting. Since fridge was 17 years old I decided to order the entire evaporator fan assembly as shown in the parts diagram including fan blade, motor brackets, motor, motor mounts, screws, etc. Getting to the assembly involved removing the ice maker unit plus the entire rear inside of the freezer section. Parts cost around... Read more
Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.
New parts. Read more
Directs airflow from evaporator through the fresh food compartment. Replace if cracked, broken, or missing to restore proper air distribution.
My husband ordered and replaced the water tank inside the refrigerator in the back. Read more
Ice maker not filling or water spilling? This fill cup directs water into the ice maker mold for proper ice production. Simple clip-on install.
Went online to appliance pro, found my model and the ice maker part number. The process was very easily. The order process was also very simple and the part was delivered promptly with installation instructions. Read more
White
Replaced dispenser kit and auger. Repair videos were a great help and resolved potential problems that I usually solved by trial and error. Thanks, Appliance Part Pros! Read more
Replacement mounting screw for refrigerator panels, brackets, and hardware. Restores secure fit when original is missing, stripped, or corroded.
Hinge missing screws. Replaced 2. Perfect now Read more
Secures the evaporator fan assembly behind the rear freezer panel. Replace if cracked, rusted, or missing to restore proper fan mounting and clearance.
Replace your worn or broken refrigerator bottom hinge pin. Supports the door and serves as the lower pivot point on the bottom hinge assembly.
Replaced the hinges and all parts pertaining to hinges on the refrigerator door. Total cost was approx. $83 and it took 1 hour this morning (Saturday). Now the door is closing tightly. The refrigerator is 10 years old. GE brand. Read more