Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This 1-1/8 in wire retaining ring locks into a groove to secure components in place. It helps prevent parts from sliding off a shaft or shifting out of position so assemblies stay aligned and operate reliably.
Based on recommendation to replace the clutch if clothes aren't spinning dry enough, I ordered a new clutch. Upon disassembly, I observed no Ring Wire/C-Clip and that the bearing appeared worn. Where did the clip go? Well, the bearing wore down such that it wore out the clip and bearing up to the sleeve of the shaft. Knocked out the old bearing, tapped in the new and was done. I disassembled the brake shoes but believe you can get the bearing in and out without doing so. Not a bad job, just... Read more
Inner tub basket holds clothing during wash cycles. Replace if cracked, rusty, or broken. Installs in center of washer between outer tub and agitator.
Ordered the parts from AppliancePartsPros - super fast shipping, and even though I opted for regular shipping all of my parts arrived the very next day, including the big and bulky inner basket. Disassembly went smoothly, simply following the directions in the AppliancePartsPros video. The only problem I had was that the inner basket simply would NOT come of the drive block no matter what I did. Struggled for a few hours trying to take it off. Then, I called AppliancePartsPros and they said it... Read more
Replaces the upper tub ring that mounts on top of the outer tub as a splash guard. Order a new ring if yours is cracked, broken, or no longer securely attached.
This was the second attempt at fixing this problem. The first repair and parts were generated by listing the problem and reviewing the potential corrections, listed on the web site. From making repairs on other clothes washers, I was confident that some of those potential causes could have been the cause. Unfortunately the counterbalance spring and suspension springs were not the cause as they were attached as intended and in good condition. I reached out for Appliance Parts Pros input... Read more
This is a small mesh filter screen that fits inside the water inlet valve to catch sediment and debris from your household water supply before it enters the washer. It prevents mineral buildup and particles from clogging or damaging the valve internals. Replace this screen if your washer is filling slowly, not filling at all, or if the screen is visibly clogged, torn, or deteriorated.
Went on internet, found a great site and learned that the cold water hose filter was very much clogged at the machine intake. Cleaned it and voila. Ordered an extra filter from Appliance Pros.com and literally was amazed that it arrive within 2 days of my internet order. Great efficiency and customer service….great experience. Will definitely use them in the future….thank you! Read more
Replacement power cord that connects your washer to the wall outlet. Includes strain relief for cable protection. Needed when original cord is damaged, pinched, shorted, or worn. Direct plug-in installation.
Bought a new cord and removed the back of the washer and unclipped the old and clipped in the new. 5 minutes tops. Read more
Secures the motor to its mounting point in your laundry center. Replace if the retainer is worn, broken, or has lost tension to prevent motor misalignment.
Replace motor hanger , grommets, and motor coupler Read more
This retainer ring is a genuine OEM replacement part sourced directly from the manufacturer for use on front load washing machines to hold the boot seal in place. The boot seal is the gasket that seals the washing machine when the door is closed to prevent water from leaking. The retainer ring is located flush against the boot seal and has either a spring clamp or screw clamp that secures it. Over time, this ring may become damaged due to the washing machine's normal use and age. If the ring is not tight, the washing machine could leak when in use. If water is coming from the door, it is a good idea to inspect and replace the retainer ring and possibly the boot as well.Unplug the washing machine to prevent electrocution. Remove the front panel, the detergent dispenser, and the kickplate to access the retainer ring. Locate the clamp on the ring and loosen it. Remove the retainer ring and set it to the side. Inspect the boot and then install the new retainer ring. Tighten the clamp and reassemble the washing machine. This retainer ring is sold as an individual unit. It is designed specifically for washing machines manufactured by Whirlpool.
Im not a repairman, so all my knowledge to fix my washer came from either youtube or online chats. I posted this to help the next dad trying to save a few bucks. Door sensor... Since door sensor worked correctly, verified that by starting washer with door open, and agitate cycle would not start until door was closed. Meaning door sensor worked correctly. Timer... In high spin cycle washer sounded correcltly spinning, but when opening door, drum was was not moving. So timer was triggering... Read more
Fix washer leaks during drain cycle with this pump-to-drain hose. If water pools under your machine when draining, this hose replacement stops the leak.
Replaced both inlet and outlet side of pump hoses. Removing the machine cover was the most difficult part of the entire project, and it was not hard at all after watching your "How to" videos. Thanks for excellent service. Read more
Secures panels or brackets in your laundry center to prevent vibration noise. Replace missing, stripped, or worn screws to restore a tight fit.
Followed online video. It was easy Read more
Upper agitator not turning or engaging? This washer clothes mover works with cam and dogs to roll laundry. DIY repair in 15-30 minutes with video guide.
Opened lid during cycle and found upper agitator not turning.Removed dust cover seal and saw cam turning but dogs were only engaging once in a while.Although I didn't need to replace the upper agitator I did anyway,along with the agitator cam kit. I watched the quick repair video and repaired the washer myself in less than 30 min. Read more
This screw and washer is an OEM replacement part used for Whirlpool washers. It is used to secure the lid switch. Each screw is sold individually. The screw measures approximately 1 inch.
After watching your repair video I disassembled my machine and replaced the broken switch with a new one from Appliance Parts Pros. Everything went smoothly and in about an hour I had it not only fixed but cleaned up my machine as well. Thank you for the repair video and for the great response on my order. Hopefully I won't need any more parts in the near future, but if I do I will not hesitate to order from APP again. Thank you. Read more
Push-in.
I saw videos on it possibly being the lid switch. I used 2 lead wires to bypass the lid switch, which indicated it was indeed the lid switch that was faulty. I ordered the lid switch, which came in 2 days. I installed it in less than 7 minutes. Read more
Agitator won't move or slips during wash? A worn drive shaft causes weak agitation. This shaft transfers motion from the gearcase to restore firm engagement.
I had to replace the drive shaft and the lower agitator. The motor coupling was also worn out. The repair was challenging because I had to rebuild the gear box. This step was really messy and I had to wait for the liquid gasket to set prior to completing the repair. Cleaning and prep of all of the parts tripled the repair time. Read more
Used for lid switch.
Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!) Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts... Read more
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
Replace your washer's anti-rattle clip to eliminate vibration noise and buzzing during cycles. Secures components with light spring tension. Confirm fit with your model number before ordering.
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.