Rds-305 Parts

Support, hinge counter restores proper hinge support and door balance for a worn or damaged hinge assembly. This replacement helps the appliance door open and close smoothly and stay aligned for reliable everyday use. What it does:

• Provides structural support to the door hinge and helps counterbalance the door
• Stabilizes hinge movement to reduce sagging, binding, or uneven closing
• Helps the door latch and seal correctly by keeping the hinge alignment consistent
• Use when you notice door droop, difficulty latching, or irregular door motion

• Installation may require partial disassembly of the door or hinge assembly—refer to the OEM instructions for your model
• Disconnect power and turn off water supply before beginning any repair
• Inspect surrounding hinge components and fasteners; replace any damaged parts and test door operation after installation

Supports the burner assembly and positions the cap for consistent flame distribution. Replace if damaged, warped, or causing burner misalignment.

Mounting screw secures panels, brackets, and trim to the appliance frame. Replace if screw is stripped, missing, or damaged to restore secure fastening.

This TH capacitor is an electrical control-circuit capacitor used on compatible Bosch appliances to help stabilize voltage and filter electrical noise for reliable control-board operation. Replacing a failed capacitor can address intermittent control issues. What it does

• Stabilizes control-board voltage and helps filter electrical noise that can cause erratic behavior.
• Supports reliable startup and operation of control circuits.
• Common symptom link: intermittent or unexplained control-board errors, erratic or non-responsive controls.
• Common symptom link: appliance displays control or error codes related to electronics or intermittently fails to start.

• Disconnect power to the appliance at the breaker before servicing to avoid shock.
• Discharge any capacitors and allow boards to sit before touching components; use appropriate ESD precautions.
• Only replace with the exact part number; confirm orientation and connector fit before reassembly.

This burner base supports the cooktop's burner cap and directs flame for even heating. It replaces a damaged or warped base to restore stable burner alignment and consistent flame pattern. What it does:

• Holds the burner cap in place and centers the gas flame
• Channels gas flow for proper burner operation
• Helps prevent wobbling or uneven heating from a warped base
• Commonly replaced when the base is cracked, corroded, or bent

• One burner base (B)

• Turn off gas supply and power to the appliance before servicing
• Remove surrounding burner components and reassemble in reverse order
• Inspect nearby seals and burner ports for damage; replace if necessary

Rounded cap that sits over your gas cooktop burner to contain and direct flames. Replace if cracked, chipped, warped, or worn from high heat exposure.

Black burner cap assembly that covers and protects the gas burner head. Replace if your cap is cracked, chipped, damaged, or missing to restore appearance.

Replaces cracked, broken, or fogged inner oven door glass on 30-inch ranges. Restores door appearance and maintains proper heat containment.

Replacement mounting screw for securing panels, brackets, and internal components. Needed when original fasteners are stripped, missing, or damaged.

Replacement screw that secures panels, covers, brackets, and trim to appliance frames. Needed when original screws are stripped, missing, or damaged.

This LP gas hood orifice controls propane flow to a range/hood burner for stable, efficient flame performance. It's a direct-replacement service part used when a burner is delivering low, uneven, or overly large flames. What it does

• Meter propane flow to the hood/top burner for correct combustion.
• Restores proper flame size and heat output when the orifice is clogged or wrong for LP conversion.
• Helps stop symptoms like sputtering, weak flames, or uneven burner performance.
• Small, threaded part that seats in the burner or valve assembly to create the correct jet size.

• Turn off gas supply and power before servicing; follow local codes for gas appliance work.
• Inspect threads and sealing surfaces; use proper thread sealant if required by manufacturer.
• Only replace with the correct orifice size for your fuel type (LP); do not mix with natural gas orifices.

90-degree elbow orifice holder for gas ranges and cooktops. Replace this gas line connector if cracked, broken, or causing improper gas flow alignment.

This metal angle flue guard protects and covers the flue opening on compatible gas ranges, helping direct exhaust and keeping nearby components shielded from heat. It restores the range's original flue trim and helps maintain safe operation. What it does:

• Replaces a bent, cracked or missing flue guard that no longer shields the flue opening
• Directs heat and combustion byproducts away from surrounding panels and components
• Helps reduce hot spots and contact with wiring or insulation near the flue area
• Restores proper fit and appearance of the cooktop/flue assembly

• One angle flue guard

• Turn off and disconnect power and gas supply before starting any repair
• Remove cooktop or access panels as required to reach the flue; retain original fasteners unless new ones are supplied
• Handle edges carefully; metal trim may be sharp

Used to hold down the jet holder assembly.