Rga720 Parts

This oven floor deflector assembly restores proper airflow and heat protection in the lower oven cavity so food cooks evenly and internal components stay shielded from direct heat. It's a direct replacement for a damaged or warped deflector. What it does:

• Redirects and evens oven heat across the lower cavity to improve baking and roasting consistency.
• Shields internal insulation and components from hot bake/broil flames and debris.
• Replaces warped, dented, or missing deflector that can cause uneven cooking or rattling.
• Helps prevent direct flame contact with oven floor and lowers risk of food drippings burning on surfaces.

• One bottom oven and deflector assembly

• Disconnect power to the appliance and allow the oven to cool completely before starting.
• Basic hand tools are typically required; follow the appliance service manual for panel removal steps.
• Handle edges carefully—metal parts may be sharp.

This spark module generates the high-voltage pulses that ignite the surface burners on your gas range or cooktop. Replacing a weak or failed module restores reliable clicking and ignition on the burners served by this 2-output (2+0) circuit. What it does:

• Generates high-voltage pulses to the surface-burner igniters when a control knob is turned to ignite
• Controls spark for two burners (2+0 configuration)
• Common failure symptoms: no clicking/spark on the affected burners, intermittent/weak spark, or needing a match to light

• 1 spark module

• Disconnect electrical power and shut off the gas supply before servicing
• Access the module (typically beneath the cooktop or behind the control panel) and label/photograph wiring for reference
• Transfer wires one at a time; ensure high-voltage leads are fully seated and the module is properly grounded
• Mount securely, reassemble, restore utilities, and test ignition on both burners

• "2+0" denotes a two-outlet surface-burner spark module; replace with the same configuration as the original

• A failed module typically affects all burners it serves; if only one burner won't spark, inspect that burner's igniter and switch first

This thermostat knob assembly replaces a worn or missing oven temperature control knob. It restores a secure, easy-to-turn control so you can select baking temperatures as intended and safely return the control to OFF when not in use.

• Mounts on the oven thermostat shaft to set and adjust temperature
• Direct replacement for a cracked, stripped, loose, or missing knob
• Use when the knob slips, rotates without engaging, falls off, or is difficult to turn
• Restores user control feel; will not resolve heating issues caused by other components

• Turn off power and let the appliance cool; shut off gas supply for gas models
• Pull the old knob straight off the thermostat shaft—do not pry against the control panel
• Align the new knob with the shaft and press straight on until fully seated
• Verify pointer alignment with OFF/temperature markings before use

Anti-tip kit.

This broil pan is the oven tray designed to catch drippings and hold food while broiling, making cleanup easier and helping food brown under high heat. Fits compatible GE ovens that use this factory broil pan. What it does:

• Holds food close to the broiler element for searing and browning.
• Collects grease and drippings to reduce smoke and make cleanup faster.
• Supports broiling racks or grids (when used with compatible inserts).
• Helps maintain consistent broil performance when the correct pan is in place.

• One broil pan (1 piece)

• Allow the oven to cool and disconnect power before handling or installing parts.
• Slide the pan onto the oven broil supports or into the broiler compartment until seated.
• Use oven mitts when removing after use; clean per manufacturer recommendations.

This replacement oven rack restores a safe, level surface for cookware inside the oven cavity. Replace a missing, bent, or damaged rack so you can load, slide, and position pans at the correct height.

• Supports bakeware and cookware in the oven; slides on the factory side rails
• Helps maintain proper spacing from heating elements for consistent results
• Common symptoms: rack is warped/bent, broken welds, flaking finish/rust, or it no longer slides smoothly
• Restores full oven capacity when a rack is missing

• Allow the oven to cool completely before handling racks
• To install, align with the side supports, tilt the front slightly upward to clear the stops, and slide into position
• Ensure both sides are fully seated and level before use
• Refer to your owner's manual for self-clean cycle recommendations regarding rack removal

This is the screw that secures the burner valve to the appliance, keeping the valve and associated controls fastened for reliable operation. Replaces a worn or missing mounting fastener to restore proper valve alignment and support. What it does:

• Secures the burner valve assembly to the appliance frame or manifold
• Keeps valve position stable to help maintain reliable burner operation
• Helps prevent movement that can cause loose connections or intermittent function
• Used when original screw is stripped, missing, or corroded

• One burner valve mounting screw

• Turn off power and gas supply to the appliance before starting any repair
• Use the correct size driver and avoid over-tightening to prevent stripping the screw or damaging the valve
• Confirm valve and surrounding components are properly aligned before final tightening

This small rubber grommet cushions and secures a range or oven door handle, helping keep the handle stable and reducing wear where the handle meets the door. It restores a snug fit and quiet operation. What it does:

• Acts as a protective bushing between the handle and door to prevent metal-on-metal contact
• Helps stop a loose, wobbly, or rattling handle
• Reduces wear on mounting holes and finish around the handle
• Provides a tight, vibration-dampening fit for the handle assembly

• Disconnect power to the appliance before starting any work
• Typically a simple press-fit replacement; handle removal may be required for access
• Inspect surrounding fasteners and mounting surfaces; replace damaged parts as needed

This oven burner assembly replaces a worn or damaged bake burner to restore reliable oven heating for gas ranges. Designed as a direct-fit assembly, it provides the burner tube and components needed for ignition and even baking performance. What it does

• Supplies the main bake flame for the oven cavity so the oven reaches and maintains cooking temperatures.
• Replaces cracked or corroded burner tubes that cause weak or no flame.
• Helps correct uneven heating or poor baking results linked to burner damage.
• Works with existing ignition and gas valve systems when properly installed.

• One complete oven burner assembly.

• Turn off gas supply and electrical power before beginning any service.
• Handle the burner and igniter carefully; avoid bending or damaging the tube or orifices.