S1070a3ww Parts

Size: 1/4 - 20 b.

Size: 8-18 b.

Size: 8-18 b.

The Wire Tie is an OEM part for GE dryers. It is used to secure and organize internal wiring, ensuring that wires remain properly positioned and do not interfere with the operation of the dryer. This part plays an important role in preventing wires from becoming tangled, pinched, or damaged during the dryer’s cycles.

Over time, the wire tie can become worn out, broken, or damaged due to prolonged exposure to heat, vibrations, or wear from normal use. A compromised wire tie can lead to loose or unsecured wiring, which may impact the performance of the dryer or cause electrical issues.

Symptoms of a bad Dryer Wire Tie include:

• Loose or unsecured internal wiring
• Interference with dryer components during operation
• Electrical malfunctions or short circuits
• Wires appearing frayed or damaged due to improper support

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Outer tub cover kit that replaces a cracked or missing washer tub cover, protecting the inner tub and helping stop rubbing, noise and fabric snags. Restores proper tub clearance for smoother drum movement and quieter operation. What it does:

• Covers the outer wash tub to protect the inner tub and fasteners from contact and wear
• Helps stop rubbing, scraping or thumping sounds caused by tub-to-tub contact
• Reduces the chance of clothes catching between the inner and outer tubs
• Restores correct tub spacing so the drum spins without interference

• Disconnect power and water supply before starting any repair
• Access may require removing the agitator or inner tub and using basic hand tools
• Inspect mounting clips, seals and surrounding components and replace any damaged items
• Test the washer on a short cycle after installation to ensure proper fit and quiet operation

This timer assembly controls the wash cycle sequence and timing so the machine advances through fill, agitate, drain and spin steps. Replaces a worn or non-advancing control to restore proper cycle sequencing. What it does:

• Selects and advances washer cycles (fill, agitate, drain, spin) based on timer position
• Restores cycle advancement when the dial won't move or the washer is stuck on one cycle
• Stops erratic or intermittent cycle changes caused by a failing timer
• Works with mechanical timer-driven cycle controls

• One timer assembly

• Disconnect power before starting; this part requires handling internal controls
• Remove the control panel or console to access and replace the timer; retain alignment of the dial and actuator
• Note and reconnect all wiring to the same terminals; avoid forcing connectors
• After installation, test multiple cycles to ensure proper advancement

This tub clamp secures the washer tub or associated hoses to keep components aligned and sealed during operation. It replaces a worn or broken clamp to reduce movement and help prevent leaks and noise. What it does:

• Holds the tub/hose connection or tub assembly parts together to maintain a tight fit
• Helps prevent leaks caused by loose or damaged clamps
• Reduces rubbing, vibration, and associated noise from a loose tub assembly
• Restores proper component alignment after clamp failure

• Disconnect power and turn off water supply before starting any repair
• Inspect mating parts (tub, hoses, mounting points) for damage and clean before installing
• Use appropriate clamp pliers or screwdriver as required; ensure clamp is seated and tightened evenly

5/16-18 tpt ihw s n

A small push-in plug button used to fill or cover an access hole or trim opening and restore a finished appearance. Designed to snap into place for a secure fit and to keep dirt and moisture out. What it does:

• Covers unused holes or fastener openings to restore a finished look
• Helps keep dirt, moisture, and debris from entering cavities
• Holds trim or panels flush by filling gaps where a fastener or post is missing
• Commonly replaced when cracked, lost, loose, or causing rattles or gaps

• One plug button

• Disconnect power to the appliance before accessing panels or trim
• Typically snaps into place—press firmly until seated; may require removing trim for access
• Avoid prying with sharp tools that can damage surrounding surfaces
• Replace only with the exact part number to ensure proper fit and finish

This tub shield protects the washer's inner drum edge from wear and keeps clothing and items from catching on the tub lip. It helps reduce fabric snags and prevents damage to the drum opening during normal use. What it does:

• Covers the exposed edge of the inner tub to prevent garments from catching or tearing
• Protects the tub rim from chips, gouges, and wear that can lead to leaks or rough spots
• Helps keep the drum seal area smooth for consistent door/tub engagement
• Commonly replaced when you see fabric snags, visible tub edge damage, or persistent abrasion marks

• One tub shield

• Disconnect power and water supply before starting any repair
• Typically installs around the inner tub lip; may require drum rotation and simple fasteners or clips
• Inspect the tub rim and door seal while replacing the shield; replace damaged seals as needed

This front panel assembly replaces a cracked, worn or damaged console face to restore your appliance's appearance and support the control components. It provides the outer housing for buttons, displays and mounting points. What it does

• Covers and protects the control area from spills, dust and impact.
• Provides mounting locations and alignment for buttons, switches and display components.
• Restores a secure, finished surface when the original panel is cracked, warped or missing.
• Resolves cosmetic issues and loose or misaligned controls that affect operation.

• One panel front assembly.

• Disconnect power (unplug or switch off breaker) before starting any repair.
• Remove any trim, bezels or clips carefully to avoid damaging adjacent parts; keep fasteners for reinstallation.
• Handle edges and mounting tabs gently; some panels use plastic clips that can break if forced.
• If the control components or display must be transferred, note connector locations and orientation before disconnecting.

2 wire insulator.

Size: 8-32 TT FL 1/2 S.