Need Help?
Call
Mounting screw used to secure panels, trim, brackets, and small appliance components. Replace a missing or damaged fastener to restore proper fit, reduce vibration, and keep parts aligned for safe operation. What it does:
New parts did the trick. Very easy to replace. Did not need to replace the base agitator, the fabric dispenser, or the screw; but, while it was apart it was simple to do. Read more
Usually ships within 4 - 14 days
Connects washer drain hose to household standpipe for a secure seal. Replace if cracked, stripped threads, or causing splashing at the drain connection.
My husband figured out that we needed the plug that goes around the hose entry point. It was an easy fix for him and no leaks. The part came quickly which was great since we have a lot of laundry. Read more
Fix loose or rattling parts with this 1/4-20 nut. Secures components in dryers, washers, and microwaves. Quick 5-minute repair restores stability.
After watching the repair video I opened up the dryer without any problems and found that the belt tension pully bearing failed and the mount arm had an excessive amount play in it. So armed with the part numbers I found here I went down to the local parts store and found that they did not stock the parts but could get them in a week. I went home and ordered them on line and had them the next day. I did vary from the video a bit. I uncliped the motor wire connector and removed the two screws... Read more
Fix a washer that won't agitate or stops mid-cycle with this brake pad kit. Replaces worn friction pads that prevent proper drum stopping. DIY-friendly repair.
Because the washer would stop mid cycle and would start again after some period of time, I presumed that there was something amiss in the drive train (i.e. motor, transmission, belt). Took the unit apart and discovered that two of the three brake pads were destroyed. Motor turned easily as did the transmission. Replaced the brake pads and reassembled. Now the washer doesn't stop as before, but will blow by all cycles never stopping to drain, spin, or rinse. It appears that they damaged... Read more
Counterweight spring for washer tub suspension system. Connects between tub leg assembly and base. Replace if broken, detached, or overstretched.
Store that sold the washer could not get the parts needed for 3 weeks due to delivery from factory. I told them I could get them with a week, I did and I was able to get a repairman in to do the job in 2 hours. Thanks to you. I didn't have the tool to replace the springs, that is why I had to get a serviceman in. I did not want to take the chance that the bracket was broken either. Read more
Replace your washer's control panel touchpad if the original is cracked, faded, or unresponsive. This overlay installs on the front control area.
Prevents oil leaks from the transmission area. Replace if you see oil puddles under your washer. Confirm fit with your model number before ordering.
I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more
I figured it had to be the flume; changed the flume and hose, mounting screws Read more
Filters debris and sediment from incoming water before it reaches the inlet valve. Replace if clogged or missing to restore proper fill flow. Confirm fit.
The machine would not run a full cycle before it cut off and had the code "FE" and water was too high. The water inlet valve needed to be replaced since it was letting in too much water at time. The repair was easy. Unplug machine and turn off cold water. Remove cold water line and drain water into bucket. Remove back two braces located at the top on each end of machine This will allow you to move top cove back about one inch. Pull back top cover about 1 inch then lift off cover. Remove... Read more
Fix a washer that won't stop filling or has water level issues. This pressure switch hose connects the tub to the control switch. Easy 15-minute repair.
Unplugged washer and called for a water truck to pump out basement, 2 feet of water. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.