Scd 302 Tp Parts

This start relay controls power to the compressor's start winding so the refrigerator can start and run. Replacing a weak or burned relay restores dependable compressor start-up and can stop repeated clicking with warming temperatures.

• Energizes the compressor's start winding to provide initial torque, then disengages from the circuit
• Common failure symptoms: refrigerator not cooling or intermittently warm; compressor hums/clicks and won't start; relay rattles, smells burnt, or shows heat damage; overload trips
• Helps prevent hard-start conditions that stress the compressor
• The relay contacts are open/shorted, the compressor may fail to start and cycle off on overload

• Disconnect power before servicing; wear appropriate PPE
• Access the rear machine compartment; remove the relay cover on the compressor. Note wire positions, pull the old relay straight off the compressor pins, transfer wires, and fully seat the new relay in the same orientation
• If equipped, safely discharge the run capacitor; inspect the overload, wiring, and terminals for heat damage and address as needed
• Reinstall the cover. If the compressor still won't start, further diagnosis of the start device, capacitor, or compressor is required

This door shelf is a direct-replacement refrigerator door bin that restores usable storage on the door and keeps bottles, jars and condiments secure. It gives a clean, functional shelf when the original is cracked, broken or missing. What it does:

• Provides a secure shelf for bottles, jars and other door-stored items.
• Replaces cracked, chipped or warped door shelves that no longer hold items safely.
• Prevents items from shifting or falling when the door is opened or closed.
• Restores proper organization and usable storage space on the refrigerator door.

• Remove all contents from the door shelf area before replacing; wear gloves if the old shelf is cracked.
• Lift the old shelf slightly and tilt to disengage from the door rails, then align and snap the new shelf into the rails.
• Most installations require no tools; if mounting clips are damaged, replace them as needed.
• Refer to your appliance owner's manual for any model-specific instructions and safety guidance.

A small replacement closure shim that helps align and secure a closure/trim piece on select appliances, restoring proper fit and reducing rattles, rubbing, or gaps for quieter, more reliable operation. What it does:

• Positions and supports the closure/trim so panels and doors close evenly.
• Helps stop rubbing, misalignment, or minor gaps that can cause noise or poor sealing.
• Serves as a non-electrical spacer/aligner where the original shim has worn or broken.
• Useful when cosmetic trimming or closure pieces feel loose or shift during use.

• Disconnect power to the appliance before starting any repair or accessing panels.
• Access location may require removing the related trim, panel, or door—refer to the appliance diagram or service manual.
• Handle small plastic parts carefully; align the shim before fastening to avoid breakage.

This part no longer includes the relay. A common substitute relay for many models is part # WP2262181. If you are unsure if this substitution is compatible with your model, please call 1-877-477-7278 for more assistance.

This defrost thermostat senses freezer temperature and opens/closes to stop the heater during normal cooling cycles, helping keep your freezer from over-defrosting and protecting stored food. Replaces a failed or intermittent defrost control sensor. What it does:

• Opens or closes at its preset temperature to stop the defrost heater when the evaporator is warm enough
• Prevents the heater from staying on continuously, reducing risk of frozen or water-leaking evaporator issues
• Commonly replaced when defrost cycles fail or frost builds on the evaporator
• Works with the refrigerator's defrost system to maintain proper ice buildup control

• Disconnect power before inspecting or replacing the thermostat to avoid shock
• Mount the thermostat on the evaporator or bracket exactly as the original; improper placement can cause incorrect operation
• Handle the sensor gently and avoid bending or kinking capillary/tubing if present

This evaporator fan blade is the rotating plastic impeller that moves cold air from the evaporator across the freezer and refrigerator compartments, restoring proper airflow for even cooling. What it does:

• Circulates air over the evaporator coil so cooled air is distributed through the appliance
• Helps maintain even temperatures throughout the fridge and freezer sections
• Worn or damaged blades can cause reduced airflow, weak cooling, or abnormal fan noise
• Replacing the blade can restore normal airflow when the motor and housing are otherwise functional

• Disconnect power to the appliance before servicing to avoid electrical shock
• Access typically requires removing the evaporator cover in the freezer compartment
• Inspect the motor shaft and blade hub for damage and ensure the blade seats securely on the motor
• If fan noise or continued airflow problems persist after installation, verify the evaporator fan motor and mounting components

This left-side freezer glide helps the freezer drawer slide smoothly and stay aligned, restoring proper drawer movement and preventing binding or sagging. Fits the freezer drawer track and supports normal opening and closing. What it does:

• Guides and supports the freezer drawer on the left side for smooth travel
• Keeps the drawer aligned to prevent scraping, sticking, or uneven movement
• Reduces chatter and wear on the drawer and track from improper seating
• Common symptom: drawer sticks, drags, or drops on one side when opening

• One left-side freezer glide

• Disconnect power before working on the appliance and remove food from the drawer area
• Remove the freezer drawer per the manual to access and replace the glide
• Use basic hand tools as required; avoid forcing parts to prevent breakage

This small button-style plug fills and finishes an unused hole or access opening on the appliance, restoring a clean appearance and helping keep out dust and moisture. It's a simple cosmetic and protective replacement. What it does:

• Covers and seals unused holes or trim openings to improve appearance
• Helps block dirt, lint, and moisture from entering panels or compartments
• Replaces worn or damaged plugs that no longer seat securely
• Provides a flush, finished look matching appliance trim

• Disconnect power to the appliance before servicing for safety.
• Typically snaps or presses into place; use a flat tool to carefully remove an old plug if needed.
• Avoid excessive force to prevent damage to surrounding trim or clips.

This replacement screw fastens internal components and panels so parts stay secure and quiet. It's a direct-fit fastener used where the original mounting screw is missing or damaged to restore proper assembly. What it does:

• Secures panels, brackets or components to prevent movement and vibration
• Restores proper alignment for covers and access panels
• Stops rattling or loose-fitting parts caused by a missing or stripped screw
• Works as the factory-specified fastener for the original mounting point

• The screw location and type before installing; use the original hole and thread
• Power off and disconnect the appliance before accessing internal components
• Start the screw by hand to avoid cross-threading, then snug with the appropriate screwdriver
• Do not overtighten — stop once the part is secure to avoid stripping or cracking

This replacement bracket secures the refrigerator ice maker assembly so it stays properly positioned for reliable ice production. It restores stable mounting and helps prevent the ice maker from shifting or coming loose. What it does:

• Holds the ice maker assembly in place on the freezer liner or mounting frame
• Keeps the ice maker aligned for proper operation and water fill
• Helps stop vibration or movement that can cause noisy operation or misfeeds
• Useful when the original bracket is bent, broken, or missing

• Disconnect power to the refrigerator and shut off the water supply before starting
• Remove the ice maker to access the bracket mounting screws
• Reuse existing screws if undamaged; tighten to secure but avoid overtightening
• If mounting points or surrounding plastic are damaged, replace or repair before reinstalling