She33m Parts

This drain hose adapter connects the appliance's drain hose to another hose or a compatible fitting, providing a secure, leak-resistant joint so wastewater can be routed to the household drain. Replace when the original adapter is cracked or loose.

• Couples the drain hose to another hose or to a sink/disposal/standpipe fitting
• Helps seal the joint to reduce leaks and hose slippage
• Restores a tight fit when the original adapter is worn, brittle, or missing
• Symptoms of a bad adapter: leaking at the connection, hose won't stay attached, visible cracks

• Disconnect power and turn off water before servicing
• Place a towel or pan to catch residual water from the hose
• Fully seat hose ends over the adapter barbs and secure with appropriate hose clamps
• Run a short test cycle and inspect all connections for leaks

This replacement switch restores reliable electrical control within your appliance. It opens and closes an electrical circuit to signal the control system, so power and functions respond consistently when the switch is actuated.

• Opens/closes an electrical circuit when the actuator is engaged
• Sends an on/off or selection signal to the control or main board
• Helps address: no response or no start, intermittent operation, stuck on/off state, or heat-damaged/burned terminals
• Direct replacement for the original switch on applicable units

• Disconnect power at the breaker and unplug the unit before servicing
• Access the control area to reach the switch; note wire locations or take a photo
• Transfer wires one at a time for correct orientation; ensure snug terminal connections
• Reinstall mounting hardware, reassemble panels, restore power, and test operation

The Strip is an OEM part for Bosch dishwashers. It serves as a protective and decorative element, enhancing the appearance of your dishwasher while providing a clean and finished look to the tub area. The trim strip is designed to fit along the edges of the dishwasher tub, covering any visible gaps. 

A bad strip can occur due to wear and tear, accidental damage, or exposure to moisture. Signs of a faulty trim strip include visible cracks, breaks, or misalignment.

Symptoms of a bad strip include:

• Visible cracks, breaks, or misalignment 
• Discoloration or fading
• A loose or ill-fitting strip

Replace your damaged or worn-out strip with this genuine OEM Bosch part to restore your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This O-ring seals the NTC (negative temperature coefficient) temperature sensor where it inserts into the appliance. It restores a watertight seal at the sensor port to help prevent leaks and maintain reliable temperature-sensing performance.

• Provides a leak-tight seal between the NTC temperature sensor and its housing/tub/sump
• Helps prevent water seepage and moisture intrusion around the sensor opening
• Common symptoms of a failed seal: drips near the base, moisture in the leak tray, flattened/cracked ring, or a sensor that feels loose
• Good practice to replace when the NTC sensor is removed for service

• Disconnect power and shut off water supply before servicing
• Access the NTC sensor, remove the old O-ring, and clean mating surfaces
• Lightly moisten the new O-ring with water; seat it evenly to avoid pinching, then reinstall the sensor fully
• Run a brief test cycle and inspect for leaks

This O-ring is a circular sealing gasket that creates a watertight joint between mating parts. Replacing a flattened or cracked ring restores a tight seal and helps prevent leaks during operation.

• Provides a compressible seal between fittings, hoses, or housings
• Helps prevent drips and leaks at joints under normal system pressure
• Maintains proper flow by keeping connections sealed
• Typical failure signs: visible cracking/flattening, seepage at a joint, pooling water near the appliance

• Disconnect power and shut off the water supply before servicing
• Relieve any line pressure and place a towel to catch residual water
• Clean and inspect mating surfaces; replace any damaged components
• Lightly lubricate the O-ring with approved silicone lubricant, seat evenly without twisting, and test for leaks after reassembly

This upper rack wheel lets the mid-range and standard dishwasher upper rack glide smoothly on its tracks. Replacing a worn or broken wheel restores easy, level rack movement for reliable loading and unloading. What it does:

• Guides and supports the upper rack along the slide rails
• Enables smooth slide-in/slide-out operation
• Helps keep the rack aligned and level
• Common symptoms: hard-to-slide rack, rack falls off track, cracked/missing wheel, rough or noisy travel

• One upper rack wheel

• Disconnect power and water supply before servicing
• Pull out the upper rack and remove rail end caps if present
• Release the locking tab/clip on the old wheel and snap the new wheel onto the rack
• Reinstall end caps and verify smooth rack travel

This factory screw secures select Bosch/BSH appliance components. Use it to replace a missing or damaged fastener so panels, brackets, or trim stay tight and rattle-free during operation.

• Tightens and holds appliance parts such as panels, brackets, or trim in place
• Helps correct issues like loose or vibrating panels caused by a missing/stripped screw
• Maintains proper fitment after service or disassembly
• Torx T20 drive head helps resist cam-out during tightening

• Unplug power and shut off any water supply before servicing
• Use a T20 Torx driver; hand-start to avoid cross-threading
• Do not overtighten—snug to manufacturer torque guidance if available
• Replace any additional missing or damaged fasteners for even clamping

Small replacement O-ring that seals the dishwasher aqua sensor assembly to maintain a watertight seal and help ensure reliable sensor operation. Fits the sensor housing to reduce leaks and protect internal electronics. What it does:

• Seals the aqua/sensor housing to prevent water from escaping the sensor area
• Helps maintain accurate sensor readings by keeping the sensor dry and properly seated
• Commonly replaced when you see water pooling or dripping near the sensor assembly
• Used during aqua-sensor, pump, or housing repairs where the original seal is damaged

• Always disconnect power and turn off the water supply before starting repairs
• Replace the O-ring only when the sensor or housing is disassembled; inspect mating surfaces for damage or debris
• Ensure the O-ring is seated evenly in its groove before reassembly to avoid pinching or leaks

Replacement door hinge tension spring that restores proper door balance and smooth opening and closing on compatible Bosch appliances. Replaces a worn or broken door spring to help prevent sagging and doors that won't stay open. What it does:

• Provides counter-tension for the door hinge so the door stays level and moves smoothly.
• Restores proper balance to doors that feel heavy, sag, or close too quickly.
• Works as the return/tension element inside the hinge assembly to control door travel.
• Common repair for door sag, uneven closing, or doors that don't remain open.

• Disconnect power (or unplug) and remove water supply if working on dishwashers; follow all safety steps before servicing.
• Spring is under tension—wear eye protection and gloves; release or install slowly and carefully.
• May require removing the door panel or hinge caps.

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

This is the right side hinge plate. For left side use 00298567.

Spring-style hose clamp that secures flexible water hoses to fittings on select appliances, helping maintain a leak-tight connection at hose joints. Keeps hoses seated to reduce leaks and ensure reliable water flow. What it does:

• Holds flexible inlet, drain, or circulation hoses tightly on barbed fittings and nipples.
• Prevents leaks and water loss at hose connections by maintaining steady clamp pressure.
• Common signs it needs replacement: dripping or pooling near hose connections, a loose or wobbly hose, or visible clamp corrosion or deformation.
• Small, inexpensive part that restores a secure hose connection when the original clamp has failed.

• Always disconnect power and shut off the water supply before servicing appliance plumbing.
• For spring-style clamps, use pliers to open the clamp, position it over the hose, and release slowly so it seats properly; ensure the hose is fully pushed onto the fitting.
• Inspect the hose and fitting for damage; replace the hose if cracked or excessively worn before installing a new clamp.
• Wear eye protection when compressing or releasing spring clamps to avoid injury from sudden release.

This electrical control switch completes or interrupts the power circuit that runs a specific appliance function, restoring on/off control for responsive operation and safer use. What it does:

• Acts as the user-activated or circuit-activated on/off control for a discrete function
• Restores power flow when the switch is made, allowing the associated component or cycle to run
• Common symptom: appliance function won't start or respond when the control is pressed or activated
• Common symptom: intermittent operation or no power to a given feature

• One switch

• Disconnect power to the appliance before attempting any service to prevent shock
• Access and replacement steps vary by model; follow the appliance service manual or schematic for safe disassembly
• Handle connectors carefully and confirm secure wiring/terminal seating after installation

The Tube Dishwasher is an OEM component for Bosch dishwashers. It is responsible for circulating water throughout critical spray arms during different cycles. 

Causes of a bad tube dishwasher can include mineral buildup reducing the tube diameter over time, physical damage from scraping dishware against the pipes, or wear from normal vibration/motion.

Symptoms of a bad tube dishwasher include:

• Incomplete spray coverage in hard-to-reach areas  
• Soft or spotty cleaning performance in certain sections
• Puddles or leaks at the tube installation points
• Dirty or stagnant water unable to circulate properly

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.