She36uc/22 Parts

This replacement switch restores reliable electrical control within your appliance. It opens and closes an electrical circuit to signal the control system, so power and functions respond consistently when the switch is actuated.

• Opens/closes an electrical circuit when the actuator is engaged
• Sends an on/off or selection signal to the control or main board
• Helps address: no response or no start, intermittent operation, stuck on/off state, or heat-damaged/burned terminals
• Direct replacement for the original switch on applicable units

• Disconnect power at the breaker and unplug the unit before servicing
• Access the control area to reach the switch; note wire locations or take a photo
• Transfer wires one at a time for correct orientation; ensure snug terminal connections
• Reinstall mounting hardware, reassemble panels, restore power, and test operation

The Panel-Facia is an OEM part for Bosch dishwashers. As the front panel interface, it houses all control buttons, displays, and status indicators.

Symptoms of a bad panel-facia can include non-responsive or stuck buttons, indecipherable displays, or cracks that compromise the panel's integrity. 

Causes of a bad panel-facia dishwasher include:

• Unresponsive or inaccurate control buttons
• Fault codes that cannot be cleared  
• Cracked or damaged fascia compromising controls
• Disrupted electronic communication preventing cycles

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This hinge cover is a molded trim piece that protects and conceals a refrigerator door hinge for a clean finished look. It helps keep hinge hardware free of dust and reduces sharp edges while restoring appearance. What it does

• Covers the door hinge area to hide hardware and improve the appliance's appearance
• Helps block dust and debris from accumulating on hinge components
• Reduces the risk of clothes or fingers catching on exposed hinge parts
• Matches OEM fit and shape to maintain proper clearance and alignment

• One hinge cover

• High-level replacement: remove the old cover and snap or screw the new cover into place (specific fasteners vary by model)
• Use basic hand tools if required; for model-specific instructions
• Disconnect power (or follow appliance-specific safety steps) before working near electrical components
• Inspect hinge and hardware while replacing the cover; replace damaged hinge components as needed

This replacement door handle restores a secure, comfortable grip for opening and closing the appliance door and refreshes the unit's appearance. Designed to match OEM fit and finish for a clean, factory look. What it does:

• Provides a sturdy grip for opening and closing the appliance door.
• Replaces cracked, loose, or broken handles that make the door hard to operate.
• Helps maintain proper door alignment and user control when opening or closing.
• Restores the appliance's finished appearance where the original handle is damaged.

• Disconnect power to the appliance before beginning any repair and follow all safety precautions.
• Installation may require removing the door trim or access panel and common hand tools (screwdriver, socket); your appliance manual for exact steps.
• Retain original fasteners; this part listing does not guarantee included hardware.

This outer door panel replaces a damaged or worn door skin to restore the appliance's exterior appearance and protect internal door components. Fits as a direct replacement to renew the door surface and finish. What it does:

• Provides the finished exterior surface for the appliance door and hides internal components
• Protects the inner door structure from impacts, scratches, and wear
• Restores cosmetic appearance when the door is dented, scratched, or has peeling finish
• Can reduce noise from a loose or warped door panel when properly fastened

• Always disconnect power (and water supply if applicable) before starting repairs.
• Handle edges and any glass or trim carefully to avoid injury or damage.
• Require removal of inner door trim, screws, and clips—use proper tools and keep fasteners organized.

Regulator with o-ring.

This actuator lever assembly with springs replaces a worn or broken control lever to restore proper mechanical movement in the appliance. It helps the dispenser/latch mechanism operate smoothly for reliable everyday use. What it does:

• Transfers motion from a control cam or motor to the latch or dispenser linkage
• Restores proper engagement when a broken or fatigued lever prevents operation
• Helps stop intermittent or failed cycle starts caused by damaged mechanical linkage
• Works as a direct-fit replacement that re-establishes spring tension and lever action

• Disconnect power before accessing internal components to avoid shock or injury
• Basic hand tools usually required; maintain original screw/hardware if reusing
• Inspect surrounding linkages and replace damaged clips or fasteners as needed

A small spring-style hose clamp used to secure flexible appliance hoses to fittings and prevent leaks. Simple, durable replacement that restores a tight connection for water and drain lines. What it does:

• Compresses around a hose to hold it firmly on an inlet, outlet or drain fitting
• Helps stop leaks caused by loose or slipping hoses
• Keeps hoses seated during normal appliance operation and vibration
• Commonly used on dishwasher and washer drain or water hoses

• One hose clip / spring clamp

• Disconnect power and water supply before starting repairs
• Use pliers to expand the clamp for removal and reinstall; ensure hose is fully seated before releasing clamp
• Inspect the hose and fitting for damage; replace any cracked or brittle hose
• Do not overtighten or deform clamp when installing; replace if corroded or weakened

This inner door is the interior panel for a dishwasher door that protects internal components and provides a finished inside surface. Replacing a damaged inner door restores proper sealing and appearance. What it does:

• Forms the interior surface of the dishwasher door and helps contain water during cycles
• Protects wiring, insulation, and electronics housed inside the door
• Helps maintain a proper seal to prevent leaks and improve wash performance
• Addresses symptoms like visible door damage, interior rust, dents, or moisture inside the door cavity

• Disconnect power and water supply before starting any repair
• Removing the outer door panel or control panel may be required;
• Keep fasteners and trim organized for reassembly; some clips or screws may be needed

This float switch lever is the actuator that moves the dishwasher's tub float to operate the water-level/flood-sensing switch, helping the appliance detect overfill and control fill/drain cycles. Replaces a worn or broken lever to restore proper float activation. What it does:

• Transfers movement from the tub float to the float switch so the machine senses water level correctly
• Commonly needed when a cracked or detached lever prevents the float from engaging the switch
• Can stop overfill-safety trips or no-fill symptoms caused by a non-responsive float assembly
• Works with the existing float and float switch; restores mechanical linkage function

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove lower access panels or tub components as required to reach the float assembly
• Inspect surrounding clips and the float for damage; replace any broken hardware
• Tighten securely but avoid over-torquing; test float movement and switch activation before reassembly

This condensation tube routes moisture from the dryer's vented condensate tank to the drain, helping prevent leaks and pooling under the appliance. It's a direct-replacement tank drain tube for compatible vented-tank models. What it does:

• Channels condensate away from the tank to the dryer drain connection to reduce water buildup.
• Helps stop leaking or pooling beneath the dryer when the tank is vented.
• Restores proper condensate flow if the original tube is cracked, clogged, or damaged.
• Compatible with vented-tank dryer assemblies that use a routed drain tube for condensate.

• Turn off and unplug the dryer before starting any repair; if applicable, shut off gas supply.
• Remove access panels as needed to reach the condensate tank and tube; avoid damaging nearby wiring or hoses.
• Ensure tube fittings seat fully and secure clamps or fasteners to prevent leaks.

This hose clamp secures flexible appliance hoses to fittings to prevent leaks and keep connections tight. It's a small replacement part that restores a secure seal at hose connections to reduce drips and water damage risk. What it does:

• Holds a rubber or plastic hose firmly to a barb or nipple to maintain a watertight connection
• Commonly used on drain, inlet, or circulation hoses where clamps can loosen or corrode
• Replaces worn, bent, or corroded clamps that allow leaks or hose slippage
• Helps stop intermittent dripping, puddling, or loss of water pressure caused by loose hoses

• One hose clamp

• Use appropriate pliers or a clamp tool; avoid over-tightening which can cut or deform the hose
• Inspect the hose and fitting; replace damaged hoses before installing the new clamp
• Disconnect power and water supply if working near electrical components or live plumbing
• Dispose of old clamps safely; wear eye protection when compressing spring-style clamps

This rubber gasket seals appliance openings to help prevent water and air leaks and restore proper door/tub sealing. It replaces a worn or damaged seal to reduce leaking and maintain normal appliance performance. What it does

• Creates a watertight/airtight barrier between mating surfaces to prevent leaks.
• Helps maintain operating temperature and efficiency by sealing the door/tub.
• Common symptom: visible water around the door or base during use.
• Common symptom: cracked, flattened, or distorted seal material that no longer compresses.
• Works as a direct replacement for the matching OEM seal when damaged or worn.

• One gasket as shown on the product page.

• Turn off power and water supply to the appliance before starting any repair.
• Remove the old seal carefully, clean the mounting channel of debris and residue, and inspect the mating surface.
• Press the new gasket evenly into the channel, starting at one corner and working around to ensure full seating without twists.
• Test the door closure and run a short cycle to confirm there are no leaks; re-seat if necessary.

Drain hose clamp