She43f5uc/64 Parts

Replace your dishwasher's broken or missing trim strip. This cosmetic part installs along the door edge to cover gaps and provide a finished look.

Insulating pad for dishwasher door or tub. Replaces worn, torn, or missing insulation that affects noise dampening and heat retention.

This replacement side panel restores the appliance's exterior finish and protects the cabinet edge from dings, scratches and wear. It's a direct-fit exterior trim piece that keeps the side of the unit looking finished and secure. What it does

• Covers and protects the appliance cabinet side from impact, scratches and cosmetic damage
• Restores a clean, factory appearance when original panel is dented, chipped or missing
• Helps maintain proper clearance and panel alignment with adjacent cabinetry
• Prevents exposed edges that can catch debris or snag clothing

• Includes: one side panel

• Disconnect power (and water supply if applicable) before starting work
• Handle panel carefully — edges may be sharp; gloves recommended
• Typically secured with screws or clips; retain hardware from the original panel or refer to the appliance parts diagram

Replace your dishwasher's upper dishrack assembly if the coating has rusted, cracked, or chipped. Includes wheels and tines. Installs in the top position.

Fix dishes not drying or cycles taking 3+ hours. This heating element heats wash water and enables drying. Moderate DIY repair with video guide.

Plastic cover that protects the drain pump mechanism from debris. Replace if cracked, broken, or tabs are bent preventing proper seal during drain cycles.

This turbidity sensor detects how clear the dishwasher's wash water is so the control can adjust cycle time, rinses, and water changes. Replacing a faulty sensor helps restore proper cleaning performance and normal cycle lengths.

• Monitors soil level/clarity of the wash water
• Signals the control to extend or shorten wash and rinse phases as needed
• Helps optimize water use while maintaining cleaning results
• Failure symptoms can include unusually long or short cycles, poor cleaning, repeated draining/refilling, or cycles that won't advance

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher out as needed; access the sensor from the base area
• Place a towel to catch residual water; release the locking tab or twist-lock, unplug the connector, and install the new sensor fully seated and locked
• Restore power/water and run a test cycle; check for leaks

Wax motor for detergent/rinse-aid dispenser.

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

This is a trim strip that attaches along the lower portion of the dishwasher door. It helps seal the door edge and provides a finished appearance to the front panel. Replace this piece if it is cracked, warped, or missing, which can lead to water leaks around the bottom of the door during wash cycles.

Tall item spray head that attaches to the upper feed tube in your dishwasher. Replace if cracked, broken, missing, or won't lock into place properly.

Front leveling leg adjusts and supports your dishwasher at the front. Replace if damaged, missing, or worn to restore proper height and stability.

This replacement switch restores reliable electrical control within your appliance. It opens and closes an electrical circuit to signal the control system, so power and functions respond consistently when the switch is actuated.

• Opens/closes an electrical circuit when the actuator is engaged
• Sends an on/off or selection signal to the control or main board
• Helps address: no response or no start, intermittent operation, stuck on/off state, or heat-damaged/burned terminals
• Direct replacement for the original switch on applicable units

• Disconnect power at the breaker and unplug the unit before servicing
• Access the control area to reach the switch; note wire locations or take a photo
• Transfer wires one at a time for correct orientation; ensure snug terminal connections
• Reinstall mounting hardware, reassemble panels, restore power, and test operation

Fix unresponsive cycle selections or worn buttons with this dishwasher control panel button. Restores proper operation of wash cycle and option controls.

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Secures hoses to fittings and prevents leaks in your dishwasher. Replace if stretched, corroded, or damaged to maintain a tight seal. Confirm fit.