She45r52uc Parts

Left side door hinge plate for your dishwasher. Replaces cracked, broken, or worn hinge plates that cause door misalignment or instability.

Protects dishwasher wiring from heat and abrasion. Replace if worn, cracked, or causing electrical shorts. Confirm fit with your model number.

Removable cutlery basket holds silverware in your dishwasher's lower rack. Replace if cracked, broken, or missing to keep utensils organized.

Replace cracked, broken, or missing dishwasher rack roller wheels. Snaps onto bottom or top rack to restore smooth gliding. Easy DIY installation.

Replace your dishwasher's upper rack pull-out rail assembly. Installs on top rack to enable smooth sliding. Needed when rails are cracked, broken, or wheels are worn. Includes left and right sides.

Replaces damaged inner door trim that supports the door panel and seals the front edge. Replace if warped, cracked, or affecting door alignment.

Dishwasher cleaner removes grease, limescale, and odor-causing residue. Use monthly or when noticing buildup or smells. Confirm compatibility with your model.

Insulation pad for dishwashers. Installs underneath or around the tub to reduce noise and retain heat. Replace if torn, compressed, or missing.

This is a display optimizing component for a dishwasher's electronic control panel. It helps regulate and enhance the clarity and function of the digital display used to select cycles and monitor wash status. Replace this part if the display appears dim, flickering, shows garbled characters, or fails to illuminate properly.

This replacement side panel restores the appliance's exterior finish and protects the cabinet edge from dings, scratches and wear. It's a direct-fit exterior trim piece that keeps the side of the unit looking finished and secure. What it does

• Covers and protects the appliance cabinet side from impact, scratches and cosmetic damage
• Restores a clean, factory appearance when original panel is dented, chipped or missing
• Helps maintain proper clearance and panel alignment with adjacent cabinetry
• Prevents exposed edges that can catch debris or snag clothing

• Includes: one side panel

• Disconnect power (and water supply if applicable) before starting work
• Handle panel carefully — edges may be sharp; gloves recommended
• Typically secured with screws or clips; retain hardware from the original panel or refer to the appliance parts diagram

Fix dishes not drying or cycles taking 3+ hours. This heating element heats wash water and enables drying. Moderate DIY repair with video guide.

Plastic cover that protects the drain pump mechanism from debris. Replace if cracked, broken, or tabs are bent preventing proper seal during drain cycles.

This turbidity sensor detects how clear the dishwasher's wash water is so the control can adjust cycle time, rinses, and water changes. Replacing a faulty sensor helps restore proper cleaning performance and normal cycle lengths.

• Monitors soil level/clarity of the wash water
• Signals the control to extend or shorten wash and rinse phases as needed
• Helps optimize water use while maintaining cleaning results
• Failure symptoms can include unusually long or short cycles, poor cleaning, repeated draining/refilling, or cycles that won't advance

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher out as needed; access the sensor from the base area
• Place a towel to catch residual water; release the locking tab or twist-lock, unplug the connector, and install the new sensor fully seated and locked
• Restore power/water and run a test cycle; check for leaks

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.