She58c05uc/43 Parts

Repair set for dishwasher rack rollers. Restores smooth rack movement when wheels are broken, cracked, or worn. Installs on upper or lower racks.

Replace your dishwasher's upper rack rail if cracked, broken, or worn. This guide rail installs along the sides to support smooth rack sliding.

Adjusting device for dishwasher height and leveling. Replaces broken, worn, or missing adjustment mechanisms. Installs at base for proper alignment.

Insulation pad for dishwashers. Installs underneath or around the tub to reduce noise and retain heat. Replace if torn, compressed, or missing.

Insulating component for dishwasher that provides thermal and sound dampening. Replace if cracked, torn, missing, or no longer adhering properly.

Detergent not dispensing during wash cycle? This actuator arm with spring releases the detergent cup at the right time. Moderate DIY repair.

Tall item spray head that attaches to the upper feed tube in your dishwasher. Replace if cracked, broken, missing, or won't lock into place properly.

This replacement switch restores reliable electrical control within your appliance. It opens and closes an electrical circuit to signal the control system, so power and functions respond consistently when the switch is actuated.

• Opens/closes an electrical circuit when the actuator is engaged
• Sends an on/off or selection signal to the control or main board
• Helps address: no response or no start, intermittent operation, stuck on/off state, or heat-damaged/burned terminals
• Direct replacement for the original switch on applicable units

• Disconnect power at the breaker and unplug the unit before servicing
• Access the control area to reach the switch; note wire locations or take a photo
• Transfer wires one at a time for correct orientation; ensure snug terminal connections
• Reinstall mounting hardware, reassemble panels, restore power, and test operation

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Replace your dishwasher's cracked, stained, or worn outer door panel. This cosmetic front panel installs on the exterior door to refresh appearance.

Right side door hinge plate for dishwashers. Secures the door hinge mechanism to the frame. Replace if cracked, broken, or damaged to restore proper fit.

The Impeller Jug is an OEM part for Bosch dishwashers. Located inside the wash chamber, the impeller jug is responsible for evenly distributing water throughout the dish rack during the wash cycle. It features strategically placed holes and channels that work with the spray arms to direct water flow and ensure all dishes receive thorough coverage. 

Symptoms of a bad impeller jug include:

• Incomplete cleaning even on short or heavy wash cycles  
• Dirty dishes remaining at the end of the cycle
• A buildup of food or grime deposits inside the wash chamber
• Off-balanced or excessive noise levels during washing

Causes of failure can be mineral or scale buildup inhibiting water flow, cracked or damaged casing allowing leaks, or worn impeller fins no longer efficiently dispersing water. Over time, hard water deposits and normal use can degrade performance. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. 

This is the cap that seals the rinse-aid dispenser reservoir on the inside of the dishwasher door. It threads or snaps into place to keep rinse aid contained until it is dispensed during the rinse cycle. Replace this cap if rinse aid leaks out prematurely, the cap is cracked or warped, or dishes are coming out spotted due to improper rinse-aid dispensing.

Spring-style hose clamp secures water and drain hoses to fittings, preventing leaks. Replace when connections loosen or clips lose tension. Confirm fit with your model number.

Captures small food particles and debris to protect your dishwasher pump and prevent clogs. Replace when clogged or damaged. Verify fit with your model.