She66c06uc/36 Parts

Plastic cover that protects the drain pump mechanism from debris. Replace if cracked, broken, or tabs are bent preventing proper seal during drain cycles.

This turbidity sensor detects how clear the dishwasher's wash water is so the control can adjust cycle time, rinses, and water changes. Replacing a faulty sensor helps restore proper cleaning performance and normal cycle lengths.

• Monitors soil level/clarity of the wash water
• Signals the control to extend or shorten wash and rinse phases as needed
• Helps optimize water use while maintaining cleaning results
• Failure symptoms can include unusually long or short cycles, poor cleaning, repeated draining/refilling, or cycles that won't advance

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher out as needed; access the sensor from the base area
• Place a towel to catch residual water; release the locking tab or twist-lock, unplug the connector, and install the new sensor fully seated and locked
• Restore power/water and run a test cycle; check for leaks

Fix dirty dishes or weak water spray with a new dishwasher spray arm. Easy 5-minute DIY repair—just unclip the old arm and snap in the replacement.

This upper trim strip finishes the top edge of the appliance's front opening, restoring a clean look and helping protect nearby components. Replace a cracked, missing, or loose strip to keep panels aligned and secure.

• Provides a finished edge along the upper portion of the door/face area
• Helps protect adjacent components from dust and minor splashes
• Maintains proper panel gaps and alignment
• Typical symptoms: visible cracks, warping, looseness, rattling, or exposed/sharp edges

• Disconnect power before servicing; also shut off water
• Remove the existing strip by releasing screws/clips; retain hardware for reuse
• Align the new strip and secure evenly—do not overtighten fasteners
• Check door/panel operation afterward to confirm proper fit and clearance

Wax motor for detergent/rinse-aid dispenser.

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

Tall item spray head that attaches to the upper feed tube in your dishwasher. Replace if cracked, broken, missing, or won't lock into place properly.

Front leveling leg adjusts and supports your dishwasher at the front. Replace if damaged, missing, or worn to restore proper height and stability.

This replacement switch restores reliable electrical control within your appliance. It opens and closes an electrical circuit to signal the control system, so power and functions respond consistently when the switch is actuated.

• Opens/closes an electrical circuit when the actuator is engaged
• Sends an on/off or selection signal to the control or main board
• Helps address: no response or no start, intermittent operation, stuck on/off state, or heat-damaged/burned terminals
• Direct replacement for the original switch on applicable units

• Disconnect power at the breaker and unplug the unit before servicing
• Access the control area to reach the switch; note wire locations or take a photo
• Transfer wires one at a time for correct orientation; ensure snug terminal connections
• Reinstall mounting hardware, reassemble panels, restore power, and test operation

This dishwasher door seal fits into the channel around the tub opening to create a tight, water-resistant barrier when the door closes. Replacing a worn seal helps stop leaks at the front of the unit and keeps cycles running efficiently. What it does:

• Forms a watertight perimeter seal between the tub and door
• Helps contain water and steam during wash and rinse cycles
• Aids proper door compression for reliable closing
• Common symptoms: water on the floor at the front, drips from door corners, visible cracks/flattening, or gaps in the gasket

• 1 door seal

• Disconnect power and turn off water supply before servicing
• Remove the old seal and clean the gasket channel thoroughly
• Start at the top center and press the new seal evenly into the groove without stretching
• Close the door to check for uniform compression, then run a short test cycle to inspect for leaks

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Color: platinum gray. It measures about 2 inches wide by 2 inches high.

The Flip Tine Latch is an OEM part for Bosch dishwashers. It serves as a latching mechanism on upper dish racks that securely holds folded tines.

Made of durable plastic, the latch features offset hooks integrated along its base edge. These engage onto roll edges of individual flip up tines, pinning them neatly against the chamber to prevent unwanted movement.

Symptoms of a failed flip tine latch include:

• Sagging or unfolded flip tines potentially blocking spray jets
• Restricted water distribution due to improper rack orientation
• Scratched or misplaced dishes from unlatched tines potentially flailing
• Inefficient cleaning from lack of optimized spray coverage

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Replace your dishwasher's cracked, stained, or worn outer door panel. This cosmetic front panel installs on the exterior door to refresh appearance.

This tube channels water from the inlet valve to the wash system inside the dishwasher. It ensures a steady supply of water reaches the spray arms for proper cleaning during wash and rinse cycles. Replace if the tube is cracked, kinked, or leaking, which can cause poor water flow, inadequate cleaning, or water pooling under the dishwasher.

This hinge cover is a molded trim piece that protects and conceals a refrigerator door hinge for a clean finished look. It helps keep hinge hardware free of dust and reduces sharp edges while restoring appearance. What it does

• Covers the door hinge area to hide hardware and improve the appliance's appearance
• Helps block dust and debris from accumulating on hinge components
• Reduces the risk of clothes or fingers catching on exposed hinge parts
• Matches OEM fit and shape to maintain proper clearance and alignment

• One hinge cover

• High-level replacement: remove the old cover and snap or screw the new cover into place (specific fasteners vary by model)
• Use basic hand tools if required; for model-specific instructions
• Disconnect power (or follow appliance-specific safety steps) before working near electrical components
• Inspect hinge and hardware while replacing the cover; replace damaged hinge components as needed

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter