Shear55uc Parts

Plastic cover that protects the drain pump mechanism from debris. Replace if cracked, broken, or tabs are bent preventing proper seal during drain cycles.

Replace a missing or damaged junction box cover on your dishwasher. Protects power supply and control board wiring connections. Easy DIY repair.

Replacement control panel facia for Bosch dishwashers. Covers control interfaces and buttons. Needed when cracked, chipped, or letters worn off from use.

Fix a dishwasher that won't start, stops mid-cycle, or is stuck on one wash setting. This control unit replaces faulty electronic circuits.

2 clamps included.

This switch is mounted on the dishwasher frame and detects when the door is properly closed to allow the wash cycle to begin. Replace it if your dishwasher won't start even with the door firmly closed, or if it stops mid-cycle unexpectedly.

This is the lower housing or base case that forms the bottom enclosure of the dishwasher. It provides structural support and helps contain water and components beneath the wash tub. Replace this part if it is cracked, warped, or leaking from the base of the unit.

This metric M4 x 8 screw secures the toe-kick/lower access panel at the base of the appliance. Replace a missing or stripped fastener to keep the kickplate tight and aligned, helping prevent looseness and noise.

• Secures the toe-kick or lower access panel to the base/frame
• Restores proper fit when the original screw is lost or damaged
• Helps reduce panel rattles and vibration
• Maintains correct alignment and clearance at the bottom edge

• Disconnect power before servicing; also shut off the water supply
• Support the panel and align holes before threading the screw
• Start by hand to avoid cross-threading; tighten snugly—do not overtighten
• Verify size matches the original; replace matching hardware together if required by your model

Push-button cap for dishwasher control panels. Replaces broken, cracked, or missing buttons to restore control functionality and panel appearance.

Fix dishwasher not heating or running for hours. This NTC temperature sensor monitors water temp and prevents overheating. Moderate DIY repair with video.

Replaces cracked, broken, or missing dishwasher base panel (toe kick). Installs at bottom front of unit. Needed when panel is damaged or missing.

Replacement door spring for dishwashers. Restores proper tension to door mechanism. Needed when original spring is broken, worn, or stretched out.

This protective cover sheet mounts to the appliance's frame to shield and support nearby components. Replacing a damaged or missing panel helps keep wiring and mechanisms protected and securely mounted, reducing vibration and preventing premature wear.

• Shields internal components from debris, moisture, and accidental contact
• Helps maintain proper alignment and support of adjacent assemblies
• Can reduce rattling or vibration when correctly secured
• Replace if bent, cracked, corroded, or missing

• Disconnect power (and water supply if applicable) before servicing
• Wear cut-resistant gloves; panel edges can be sharp
• Note and retain original fasteners/clips for reuse
• Route wires and seals carefully to avoid pinching; align panel before tightening fasteners

This support is a factory replacement component that holds and stabilizes a specific part within your appliance so it stays aligned and secure. Replacing a cracked or missing support restores proper fit and helps prevent noise or binding.

• Provides structural support and alignment for the designated component
• Keeps parts seated securely to minimize movement and vibration during use
• A damaged or missing support can cause looseness, rattling, sagging, or misalignment
• Restores proper fit and function when the original is cracked, warped, or broken

• Disconnect power and shut off any gas/water supplies before servicing
• Refer to your model's parts diagram to identify location and orientation
• Install using the appliance's existing screws or clips; avoid overtightening to prevent damage
• Wear cut-resistant gloves; beware of sharp edges and pinch points

Front-facing control panel facia for dishwashers. Houses buttons and digital display. Replace if cracked, broken, or attachment points are damaged.

This button replaces a worn or missing pushbutton on the appliance's control panel. It restores a positive, reliable feel when selecting settings and ensures your press properly actuates the underlying switch.

• Serves as the fingertip interface on the control console
• Transfers your press to the user interface/microswitch behind the panel
• Helps restore proper selection and start/stop response
• Typical symptoms: cracked or missing cap, sticking button, loose fit, or presses that don't register

• Disconnect power before servicing
• Remove the console/control panel to access the old button
• Note orientation; release retaining tabs and install the new button fully seated
• Reassemble the panel and test all button functions