Shearf5uc/08 Parts

Front facia panel for dishwashers. Houses control buttons and display. Replace when cracked, broken, or tabs are damaged. Installs on door front.

Decorative outer door panel for Bosch dishwashers. Replace cracked, dented, or discolored panels or change color from black/white to stainless steel.

This replacement switch restores reliable electrical control within your appliance. It opens and closes an electrical circuit to signal the control system, so power and functions respond consistently when the switch is actuated.

• Opens/closes an electrical circuit when the actuator is engaged
• Sends an on/off or selection signal to the control or main board
• Helps address: no response or no start, intermittent operation, stuck on/off state, or heat-damaged/burned terminals
• Direct replacement for the original switch on applicable units

• Disconnect power at the breaker and unplug the unit before servicing
• Access the control area to reach the switch; note wire locations or take a photo
• Transfer wires one at a time for correct orientation; ensure snug terminal connections
• Reinstall mounting hardware, reassemble panels, restore power, and test operation

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Guides the upper rack smoothly along slide rails. Replace when worn or broken to restore easy, level rack movement for reliable loading and unloading.

Replace your dishwasher's outer door panel if it's cracked, dented, scratched, or you want to change the color. Forms the exterior shell of the door.

Insulates and seals your dishwasher to contain heat and moisture. Replace if damaged, worn, or missing to restore efficiency. Verify fit with your model.

Secures hoses to fittings and prevents leaks in your dishwasher. Replace if stretched, corroded, or damaged to maintain a tight seal. Confirm fit.

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

Genuine dishwasher holder that secures components in place. Replace if cracked, broken, or missing to restore proper positioning and stability.

Right side door hinge plate for dishwashers. Secures the door hinge mechanism to the frame. Replace if cracked, broken, or damaged to restore proper fit.

Replaces cracked, dented, or worn dishwasher outer door panel. Restores exterior appearance and protects internal components. Easy DIY install.

Replace your dishwasher's door handle if the original is cracked, broken, or worn. Restores a secure grip and refreshes the appliance's appearance.

This is the cap that seals the rinse-aid dispenser reservoir on the inside of the dishwasher door. It threads or snaps into place to keep rinse aid contained until it is dispensed during the rinse cycle. Replace this cap if rinse aid leaks out prematurely, the cap is cracked or warped, or dishes are coming out spotted due to improper rinse-aid dispensing.

This hinge cover is a molded trim piece that protects and conceals a refrigerator door hinge for a clean finished look. It helps keep hinge hardware free of dust and reduces sharp edges while restoring appearance. What it does

• Covers the door hinge area to hide hardware and improve the appliance's appearance
• Helps block dust and debris from accumulating on hinge components
• Reduces the risk of clothes or fingers catching on exposed hinge parts
• Matches OEM fit and shape to maintain proper clearance and alignment

• One hinge cover

• High-level replacement: remove the old cover and snap or screw the new cover into place (specific fasteners vary by model)
• Use basic hand tools if required; for model-specific instructions
• Disconnect power (or follow appliance-specific safety steps) before working near electrical components
• Inspect hinge and hardware while replacing the cover; replace damaged hinge components as needed

Spring-style hose clamp secures water and drain hoses to fittings, preventing leaks. Replace when connections loosen or clips lose tension. Confirm fit with your model number.