Shem78w55n/10 Parts

The dishwasher insulation is an OEM component specifically designed for Bosch dishwashers. Installed between the dishwasher tub and outer door panel, this insulation serves a crucial purpose. 

Symptoms of a bad dishwasher insulation include:

• Loss of insulating properties allowing heat transfer between interior and exterior surfaces 
• Damage, cracks or breaks that compromise its insulating barrier
• Looseness, misalignment or complete absence from its designated position

Over time, insulation can deteriorate due to normal wear and environmental exposure. Without proper insulation, energy efficiency suffers along with wash and dry performance. 

This Bosch OEM replacement part is compatible with Thermador, Gaggenau, and some Kenmore models.

This fine filter sits in the dishwasher's sump filter system. It screens out small food particles so wash water stays cleaner, helping prevent debris from recirculating onto dishes and protecting internal wash components for consistent cleaning performance. What it does:

• Traps fine debris before it recirculates through the spray system
• Helps maintain water clarity for more consistent cleaning results
• Worn, torn, or warped mesh can lead to gritty residue, particles on dishes, or odors
• Replace if the filter is damaged, missing, or will not lock in place

• 1 fine filter

• Power off the dishwasher, open the door, and remove the lower rack
• Turn the filter assembly counterclockwise to unlock and lift it out
• Separate the fine filter and install the new one
• Reinstall and lock the assembly clockwise until fully seated; do not force

Keep your appliance running as designed with this genuine replacement part. It's engineered for an exact fit to restore proper operation when the original component is worn, damaged, or faulty.

• Replaces a failed original component to restore intended function
• Can help address issues such as poor performance, intermittent operation, unusual noises, or error codes
• Built to match the original fit and connection points on compatible models
• Durable, factory-specified component for reliable service

• Disconnect power (and shut off water or gas if applicable) before servicing
• Use appropriate hand tools and protective gloves
• Follow your model's service manual; note wire/part locations before removal
• Verify correct operation before reassembling covers and panels

The Hinge Plate Assembly is an OEM replacement part for Bosch dishwashers. This assembly consists of the outer hinge bracket and internal mounting plate that together secure the dishwasher door. 

Causes of a bad assembly tend to be repetitive stress from normal usage, as well as potential damage from forced or improper door openings/closings over time. 

Symptoms include: 

• Loosening or sagging of the door during wash cycles  
• Difficulty smoothly operating or securing the door
• Alignment problems affecting seals or balanced movement

This OEM Bosch replacement part is also compatible with Siemens, Thermador, and some LG dishwasher models. 

CABLE HARNESS

The Sealing is an OEM part for Bosch dishwashers. It serves as a protective barrier between the control panel and the internal components of the dishwasher, preventing moisture and dust from entering and causing damage.

A bad sealing can occur due to wear and tear, exposure to moisture, or accidental damage. Signs of a faulty sealing include water seeping into the control panel, visible cracks or gaps, or a loose fit.

Symptoms of a bad sealing include:

• Water or moisture around the control panel
• Visible cracks or gaps in the sealing
• A loose or ill-fitting seal

Replace your damaged or worn-out sealing with this genuine OEM Bosch part to restore your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

The Leveling Foot is an OEM part for Bosch dishwashers. It is designed to provide stability by allowing you to adjust the height of the dishwasher, ensuring it is level on uneven flooring.

Causes of a bad leveling foot can include wear and tear over time, damage from excessive force or impact, or thread stripping from frequent adjustments.

Symptoms of a bad leveling foot include:

• The dishwasher rocking or wobbling during operation
• Difficulty in achieving a level position
• Increased noise or vibration when the dishwasher is running

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Float Housing is an OEM part for Bosch dishwashers. It is the part that houses the float assembly, which is responsible for detecting the water level inside the dishwasher tub during operation.

Causes of a malfunctioning or damaged Float Housing can range from debris or mineral buildup preventing proper float movement, to cracks or breaks in the housing itself due to age, heat exposure, or impact.  

Symptoms of a bad Float Housing can include:

• Water leaks or flooding from the dishwasher
• The dishwasher not filling with water or overfilling
• Error codes related to water level sensing issues
• The float itself getting stuck or failing to move freely within the housing

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This kit replaces the sliding rails that support and guide the upper dishrack, restoring smooth, level movement so the rack doesn't bind, tip, or drop during loading and unloading.

• Guides the upper rack in and out along the tub sidewalls
• Helps correct a sticking, uneven, or hard-to-slide upper rack
• Can reduce issues like a sagging rack or difficulty engaging rack stops
• Wear from age, heavy loads, or corrosion can require replacement

• Disconnect power and shut off water before servicing
• Remove the upper rack and stops to access and swap the rails
• Transfer any hardware from the old rails
• Test rack travel and ensure stops are secure before restoring power

The Cover is an OEM part for Bosch dishwashers. Designed to securely seal the sump area, this part prevents leaks and ensures that water is properly circulated and drained during the dishwashing cycle. 

Causes of failure might include physical damage such as cracks or warping, which can compromise the seal, or the buildup of debris that prevents proper seating of the cover. 

Symptoms of a failing Cover include:

• Water leaks from the bottom of the dishwasher
• Poor washing performance due to inadequate water circulation
• Unusual noises as the pump struggles to draw or expel water
• Visible damage or warping of the cover itself

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This inner door panel forms the inside surface of the dishwasher door. It supports key door components and helps seal the tub, keeping water and heat contained for reliable, quiet operation.

• Provides the structural interior panel of the door
• Mounts the detergent dispenser, latch, and vent components
• Works with the door gasket to contain water and steam
• Typical symptoms include dents/rust, leaks at the door area, or a loose/misaligned dispenser or latch

• Disconnect electrical power and turn off the water supply before starting
• Open the door, support the outer panel, and remove perimeter screws to separate the door halves
• Transfer the dispenser, latch/lock, vent, wiring, and insulation from the old panel to the new one; reuse hardware and seals if in good condition
• Ensure the door gasket seats evenly; after reassembly, run a short test cycle and check for leaks

The Outer Door is an OEM part for Bosch dishwashers. Composed of durable stainless steel, it withstands cleaning chemicals while protecting the internal components. 

Symptoms of a bad outer door include:

• Dents, scratches, or rusting affecting the appearance   
• Leaks or moisture ingress from a compromised seal
• Looseness, sagging, or improper alignment
• Broken or missing handle/latch components

Causes of failure could include normal wear over time from daily use. Accidental dents from cookware or impact damage could also affect performance. 

Replacing with this OEM Bosch outer door restores protective function. Compatible with 300/500 freestanding and built-in models, its premium materials meet quality standards. This OEM Bosch part can also be used on Thermador and Gaggenau appliances.
 

The Holder is an OEM component specifically designed for Bosch dishwashers. It secures serveware and accessories safely inside the tub during wash cycles. Flexible yet durable prongs provide adjustable containment for maximum loading efficiency.

Causes of a bad holder can include normal wear and tear until prongs warp or weaken, inhibiting proper holding. Damage from loading large pots may also cause replacement needs.

Symptoms of a bad holder include:

• Serveware that shifts or falls during washing, resulting in noisy cycles  
• Containment prongs that are loose, misshapen, or cracked from use
• Reduced loading capacity

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. Replace yours to optimize organization and minimize breakage during every wash.
 

The Detergent Dispenser Seal is an OEM part for Bosch dishwashers. Located inside the detergent dispenser compartment, it creates a water-tight barrier, preventing premature detergent dissolution and leaks. Working seamlessly with the dispenser system, the seal facilitates controlled detergent release for optimum cleaning performance cycle after cycle. 

Causes for a bad detergent dispenser seal can include wear and tear from repeated use, deformations due to temperature fluctuations, and cracks or splits from general use.  

Symptoms of a bad detergent dispenser seal include:

• Detergent residue or puddles inside the dishwasher  
• Premature detergent dissolution before the main wash
• Leaks or drips from the dispenser area when closed
• Ineffective or inconsistent cleaning ability

This genuine Bosch detergent dispenser seal replacement will restore its water-tight barrier. It is also compatible with some Thermador, Siemens, and select Kenmore models.

This door latch interlock secures the appliance door and signals the control when it's safely closed, allowing cycles to start and run without interruption. Replacing a worn latch restores reliable starts and proper safety interlock function.

• Locks the door closed during operation to prevent interruptions
• Sends a "door closed" signal to the control so a cycle can start
• May resolve issues like failure to start or stopping when the door is bumped
• Helpful when the door won't click shut or shows a "door open" alert

• Disconnect electrical power at the breaker before servicing
• Open the door and remove the inner-door screws to access the latch area
• Move connectors one at a time to the new latch; ensure each is fully seated
• Reassemble, verify the strike aligns for a positive "click," and run a short test cycle

This replacement screw secures panels, brackets, and internal parts in your appliance for a tight, rattle-free fit. Use it to replace lost, stripped, or corroded hardware and keep components properly fastened.

• Fastens components to the appliance frame or assemblies
• Replaces a missing, stripped, or rusted original screw
• Helps reduce rattling or vibration from loose hardware
• Restores proper alignment of panels or brackets

• Disconnect power and shut off water before servicing
• Refer to your model's parts diagram to locate and place
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening