Shp65t52uc Parts

This inner door panel forms the inside surface of the dishwasher door. It supports key door components and helps seal the tub, keeping water and heat contained for reliable, quiet operation.

• Provides the structural interior panel of the door
• Mounts the detergent dispenser, latch, and vent components
• Works with the door gasket to contain water and steam
• Typical symptoms include dents/rust, leaks at the door area, or a loose/misaligned dispenser or latch

• Disconnect electrical power and turn off the water supply before starting
• Open the door, support the outer panel, and remove perimeter screws to separate the door halves
• Transfer the dispenser, latch/lock, vent, wiring, and insulation from the old panel to the new one; reuse hardware and seals if in good condition
• Ensure the door gasket seats evenly; after reassembly, run a short test cycle and check for leaks

The Wire Harness is an OEM component specifically designed for select Bosch dishwashers requiring electrical connections between moving components. It facilitates signal and current pathways throughout appliance frames.

Reinforced flexing sections bend without kinks accommodating shifting door movements. While connector joints remain snug against jostling. This daisy chain design simplifies diagnostics and maintenance procedures compared to individual wiring. 

Symptoms signaling the need for a new harness include:

• Intermittent cycle malfunctions indicating loose or corroded connections  
• Broken or cracked housing exposing live conductors to shorting hazards
• Overly taut sections hindering the intended range of component motions

Causes relate to prolonged abrasion stresses and water damage compromising insulation throughout thousands of cycles. Physical damage during repairs may require a complete replacement of this integral wiring backbone.

This OEM Bosch replacement harness is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers relying on consistent control schemes. Reinstallation restores reliable electrical pathways.
 

This replacement hose channels water between assemblies inside your appliance to keep cycles running smoothly and leak-free. Replacing a brittle, cracked, or leaking hose restores proper water flow and helps prevent puddles or water damage.

• Routes water between internal components during operation
• Maintains a sealed path to help prevent leaks
• Common failure symptoms: visible cracks or kinks, water leaking, standing water, or moisture under the unit
• Restores proper water flow when the original hose is worn, swollen, or loose at the fittings

• Disconnect power and turn off the water supply before servicing
• Place towels or a shallow pan to catch residual water
• Note routing and clamp positions; transfer existing clamps/seals if applicable
• Fully seat connections and tighten clamps; run a test cycle and check for leaks

The Control Module is an OEM part for Bosch dishwashers. This module controls all the electronics and programming that run the dishwasher cycles. It monitors temperatures, times dishes, and ensures the appropriate levels of water, detergent and heat are used in each cycle.

Over time electronic components can fail or become damaged. Accidental impact or water exposure can also cause issues.

Symptoms of a bad control module include: 

• Failure to start or run cycles properly
• Error codes appearing
• Incorrect temperatures being reached
• Cycles not completing fully or partially running cycles 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This replacement handle restores a secure, comfortable grip so you can open and close your appliance smoothly. Swap out a cracked or loose handle to regain confident operation and a clean, finished look.

• Provides the grasp point to open and close the appliance door or drawer
• Transfers pulling force to the door without flexing when properly fastened
• Helps maintain alignment and protect the panel/finish
• Replace when the handle is cracked, broken, missing, or wobbly/loose

• Disconnect power to the appliance; also shut off water to the unit
• Protect surrounding surfaces with tape or a soft cloth to prevent scratches
• Remove set screws or mounting bolts from the old handle and retain hardware for reuse
• Align the new handle and tighten fasteners evenly; verify smooth operation and alignment

The Power Module is an OEM part for Bosch dishwashers. It is an electronic control board located inside the dishwasher that functions as the central "brain". The power module regulates essential operations such as dispensing, washing cycles, draining/spinning, heating, and more. 

Symptoms of a bad power module include:

• The dishwasher not starting or running through cycles properly  
• Error codes displayed related to electrical faults
• Buzzing sounds coming from the module
• Lights on the control panel not illuminating

Causes can include liquid damage, loose connections losing communication over time, or failure of internal transistors/chips from years of continuous usage. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models. 

The Detergent Dispenser Seal is an OEM part for Bosch dishwashers. Located inside the detergent dispenser compartment, it creates a water-tight barrier, preventing premature detergent dissolution and leaks. Working seamlessly with the dispenser system, the seal facilitates controlled detergent release for optimum cleaning performance cycle after cycle. 

Causes for a bad detergent dispenser seal can include wear and tear from repeated use, deformations due to temperature fluctuations, and cracks or splits from general use.  

Symptoms of a bad detergent dispenser seal include:

• Detergent residue or puddles inside the dishwasher  
• Premature detergent dissolution before the main wash
• Leaks or drips from the dispenser area when closed
• Ineffective or inconsistent cleaning ability

This genuine Bosch detergent dispenser seal replacement will restore its water-tight barrier. It is also compatible with some Thermador, Siemens, and select Kenmore models.

This replacement screw secures panels, brackets, and internal parts in your appliance for a tight, rattle-free fit. Use it to replace lost, stripped, or corroded hardware and keep components properly fastened.

• Fastens components to the appliance frame or assemblies
• Replaces a missing, stripped, or rusted original screw
• Helps reduce rattling or vibration from loose hardware
• Restores proper alignment of panels or brackets

• Disconnect power and shut off water before servicing
• Refer to your model's parts diagram to locate and place
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening

The Terminal Block is an OEM part for Bosch dishwashers. It serves as the connection point where the household electrical power supply is connected to the dishwasher's internal wiring harness.

Causes of a malfunctioning Terminal Block can include loose connections allowing arcing or short circuits, corrosion buildup due to moisture exposure, or physical damage from impact.  

Symptoms of a bad Terminal Block include:

• No power to the dishwasher at all
• Intermittent power issues or the dishwasher unexpectedly losing power
• Signs of overheating, burning or arcing around the terminal block area

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Strip is an OEM part for Bosch dishwashers. It serves as a protective and decorative element, enhancing the appearance of your dishwasher while providing a clean and finished look to the tub area. The trim strip is designed to fit along the edges of the dishwasher tub, covering any visible gaps. 

A bad strip can occur due to wear and tear, accidental damage, or exposure to moisture. Signs of a faulty trim strip include visible cracks, breaks, or misalignment.

Symptoms of a bad strip include:

• Visible cracks, breaks, or misalignment 
• Discoloration or fading
• A loose or ill-fitting strip

Replace your damaged or worn-out strip with this genuine OEM Bosch part to restore your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This metric M4 x 8 screw secures the toe-kick/lower access panel at the base of the appliance. Replace a missing or stripped fastener to keep the kickplate tight and aligned, helping prevent looseness and noise.

• Secures the toe-kick or lower access panel to the base/frame
• Restores proper fit when the original screw is lost or damaged
• Helps reduce panel rattles and vibration
• Maintains correct alignment and clearance at the bottom edge

• Disconnect power before servicing; also shut off the water supply
• Support the panel and align holes before threading the screw
• Start by hand to avoid cross-threading; tighten snugly—do not overtighten
• Verify size matches the original; replace matching hardware together if required by your model

The Cover is an OEM part for Bosch dishwashers. It serves as a protective barrier over vulnerable inner components. The cover helps prevent damage from spills, shields electronics from moisture, and blocks access to moving parts for safety.

Causes of a bad cover can be normal wear and tear, repeated impact damage, or improper handling during repairs.

Symptoms of a bad cover include:

• Cracks, holes or other physical damage
• Warping or deformation over time
• Loose or improper fit that exposes internal parts

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This bottom case is the lower housing shell for the unit. It forms the base that supports internal components and exterior panels. Replacing a cracked or damaged case restores structural integrity, stability, and proper fit.

• Forms the appliance's lower housing/base and supports internal assemblies
• Provides mounting points for screws, feet, and covers
• Helps protect wiring and components from impact or abrasion
• Common signs of failure: cracked or warped housing, broken tabs/bosses, wobbling base, panels that won't seat correctly

• Disconnect power before servicing; allow the unit to cool
• Remove lower screws/fasteners and carefully separate the housing
• Transfer any feet, inserts, or strain reliefs from the old case to the new one
• Route wiring carefully and avoid pinching before reinstalling fasteners and testing

This factory-programmed electronic control module—often called the main control board—governs cycle logic and component operation. Replacing a failed module restores normal function when the appliance won't start or advance, shows control errors, or is unresponsive.

• Coordinates the timing and execution of selected cycles
• Routes power to motors, valves, heaters, and other loads as needed
• Processes inputs from sensors and the user interface
• Common signs of failure: dead controls, won't start, stops mid-cycle, erratic lights/beeps, or control-related error codes

• Disconnect power at the breaker or unplug before servicing
• Use anti-static precautions; handle the board by the edges
• Photograph wiring/connector locations and move connectors one at a time to the new module
• Ensure all connectors are fully seated and the module is securely mounted; restore power and run a test/diagnostic cycle per service instructions

This sump screw secures the dishwasher's sump or sump cover to the tub, keeping the assembly tight and leak-resistant. Replace a missing, stripped, or damaged screw to restore a proper seal and stable mounting.

• Fastens the sump or sump cover to the dishwasher tub
• Helps maintain a watertight seal to reduce leaks
• Keeps filter/sump components aligned and secure
• Replaces missing, stripped, or damaged hardware
• Helps address leaks or rattling around the sump area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack and filters to access the sump area
• Ensure mating surfaces and seals are clean and properly seated
• Tighten snugly by hand; do not overtighten to avoid stripping

The Divertor Motor is an OEM part for Bosch dishwashers.  This part controls the direction of water flow within the unit. This motor directs the water to different spray arms based on the selected wash cycle, ensuring efficient cleaning by optimizing water usage and spray intensity. 

Causes of damage to the divertor motor can include regular wear and tear, exposure to water and detergent over time, and electrical issues such as wiring problems or faults in the control board.

Symptoms of a failing Divertor Motor include:

• Inadequate water distribution during cycles, which can lead to uneven cleaning results.
• The dishwasher making unusual noises, such as humming or grinding, which may indicate a struggle in the motor function.
• Certain wash zones receiving little to no water, affecting the appliance's overall performance.
• Error codes displayed on the dishwasher panel that relate to water circulation problems.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.