Shpm65z52n/20 Parts

This support is a factory replacement component that holds and stabilizes a specific part within your appliance so it stays aligned and secure. Replacing a cracked or missing support restores proper fit and helps prevent noise or binding.

• Provides structural support and alignment for the designated component
• Keeps parts seated securely to minimize movement and vibration during use
• A damaged or missing support can cause looseness, rattling, sagging, or misalignment
• Restores proper fit and function when the original is cracked, warped, or broken

• Disconnect power and shut off any gas/water supplies before servicing
• Refer to your model's parts diagram to identify location and orientation
• Install using the appliance's existing screws or clips; avoid overtightening to prevent damage
• Wear cut-resistant gloves; beware of sharp edges and pinch points

This lock clamp secures an appliance component or assembly so it stays properly seated during operation. Replacing a worn or missing clamp helps restore a stable, rattle-free fit and reliable performance. What it does:

• Holds mating parts together to prevent shifting or vibration
• Helps maintain correct alignment of the secured component
• Can resolve issues where a part won't stay attached or seated
• Restore normal operation when the original clamp is broken or missing

• One lock clamp

• Disconnect power (and shut off water/gas if applicable) before servicing
• Note the clamp's original orientation; take a photo to aid reassembly
• Seat the component fully, then engage the clamp securely without over-stressing it
• Reassemble and test for a firm, stable fit before returning the appliance to service

This temperature sensor (NTC) monitors wash temperature and reports it to the control so the cycle heats and advances correctly. Replacing a faulty sensor can restore proper cleaning performance and normal cycle times. What it does:

• Measures water temperature and sends resistance changes (NTC) to the control
• Helps the control regulate heating and cycle progression
• Failure symptoms can include no/insufficient heat, extended cycles, or poor drying
• May trigger a temperature-sensor fault (e.g., E11 on some models)

• 1 temperature sensor

• Disconnect power and turn off water supply before servicing
• Access is typically at the sump/heat-pump area; remove the toe-kick/lower panel as needed
• Expect some residual water; place a towel or tray to catch drips
• Ensure the sensor seats fully and the seal is in good condition to prevent leaks

This repair set renews the hinge pivot components so the door opens smoothly and closes squarely. Replacing the worn hardware helps maintain proper alignment and a tight gasket seal for consistent performance. What it does:

• Replaces worn hinge pin/bushing hardware to restore door support
• Helps fix a door that sags, scrapes, or won't close flush
• Can reduce clicking, squeaking, or grinding at the hinge
• Helps the door seal make full contact to prevent warm air leaks

• 1 repair set

• Disconnect power; if applicable, turn off the water supply
• Remove items from the door; support the door and lift it off the hinge
• Install the new hinge hardware in the original orientation
• Reinstall and align the door; verify gasket seal and adjust leveling if needed

The Door Opening Module is an OEM part for Bosch dishwashers. It is an electronic sub-assembly that controls opening and closing of the dishwasher door.

Contained within the module are sensors and an actuator motor. Based on input signals, its internal programming directs the motor to safely open or close the door at precisely timed stages of washing cycles. This allows seamless loading and unloading of dishes.

Causes of failure can include obstructed or damaged sensors preventing proper operation over extended use.

Symptoms of a bad door opening module include:

• The door failing to open or close automatically during cycles
• Door remaining locked when sensing it's time to unload
• Error codes displayed relating to door functions
• Excessive noise or resistance from the motorized latch

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This Bottom Case is the lower housing of the appliance. It forms the structural base that supports and protects internal components, helping restore proper alignment and stability when the original base is cracked, warped, or damaged.

• Provides the mounting base for key assemblies and exterior panels
• Helps protect internal parts from impact and debris
• Maintains chassis alignment to reduce vibration, rattling, or poor panel fit
• Replace if the original base is broken, warped, or otherwise compromised

• Disconnect power and, if applicable, shut off water before servicing
• Edges can be sharp; wear cut-resistant gloves and eye protection
• Access typically requires removing lower/outer panels; transfer any hardware or seals from the old base
• Before reassembly and testing

This factory screw secures select Bosch/BSH appliance components. Use it to replace a missing or damaged fastener so panels, brackets, or trim stay tight and rattle-free during operation.

• Tightens and holds appliance parts such as panels, brackets, or trim in place
• Helps correct issues like loose or vibrating panels caused by a missing/stripped screw
• Maintains proper fitment after service or disassembly
• Torx T20 drive head helps resist cam-out during tightening

• Unplug power and shut off any water supply before servicing
• Use a T20 Torx driver; hand-start to avoid cross-threading
• Do not overtighten—snug to manufacturer torque guidance if available
• Replace any additional missing or damaged fasteners for even clamping

The outer door is an OEM component specifically designed for Bosch dishwashers. The outer door acts as a protective barrier, shielding internal components from potential damage while providing users access to loading and unloading dishes. 

Causes of a bad outer door can include dents, scratches, or cracks that compromise the integrity of the barrier. Warping of the door can also occur from prolonged exposure to heat and steam during the wash cycle. 

Symptoms of a bad outer door include:

• Gaps or openings appearing around the door sealing the surface
• The door not closing or latching properly 
• Excess moisture or water leakage from within the dishwasher
• Impaired thermal insulation properties reducing cleaning effectiveness

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models. 

The Indicator Light is an OEM part for Bosch dishwashers. It serves as a visual cue, providing important status updates and notifications related to the dishwasher's operation.

Causes of a malfunctioning Indicator Light can stem from issues with the control board or wiring harness that powers the light, or the light itself burning out due to age or electrical surges.

Symptoms of a bad Indicator Light include:

• The light not illuminating at all, even when it should be on
• Flickering or dimming of the light during operation
• The wrong indicator light turning on or staying on inappropriately

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This factory fastener secures panels, brackets, and internal components in your appliance. Replacing a missing or damaged screw restores a snug fit, reduces vibration and rattles, and keeps assemblies properly aligned during service or reassembly.

• Anchors panels, trim, and internal parts to the appliance frame or subassemblies
• Helps prevent vibration, buzzing, and loose or shifting components
• Ideal replacement for lost, stripped, or corroded hardware
• Common symptoms include loose panels, gaps, rattling noises, or parts that won't stay secured

• Disconnect power and shut off water or gas before servicing
• Match this screw to the original and replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; use the correct driver and do not overtighten
• Inspect the mating clip/insert; replace if stripped or damaged for a secure hold

This replacement worm gear is a small plastic drive gear that transmits rotational motion between the motor and driven components, restoring normal gear-driven movement and reducing slipping or grinding. What it does:

• Transfers torque from the motor to the mating gear or gearbox for proper mechanical operation
• Replaces worn, stripped, or damaged worm teeth that cause slipping or loss of drive
• Stops grinding, clicking, or intermittent movement when the gear is the fault
• Helps restore smooth, consistent operation of the driven mechanism when installed correctly

• One worm gear

• Disconnect power to the appliance before beginning any repair
• Inspect mating gears and shafts for wear; replace worn parts to prevent repeat failure
• Use OEM-approved lubricant only where specified; do not force or overtighten mating components

This holder secures internal components to keep assemblies aligned and stable, reducing vibration and wear. It's a simple replacement that restores proper fit where a broken or missing clip causes loose panels or noisy operation. What it does

• Secures and aligns panels or wiring harnesses inside the appliance
• Prevents rattling, vibration, and misalignment caused by damaged or missing clips
• Helps maintain proper component spacing to avoid wear or interference
• Restores secure attachment after breakage or plastic fatigue

• Disconnect power and water before starting any repair
• Remove access panels or trim to reach the damaged clip—keep fasteners organized
• Press or snap the holder into place; replace any broken tabs before reassembling
• If plastic anchors are damaged, replace them with matching OEM clips

This insulating part helps isolate and protect internal components from heat and vibration, preserving appliance performance and safety. It replaces worn or damaged insulation to restore proper thermal separation. What it does:

• Provides thermal and vibration isolation for internal appliance components
• Helps prevent heat transfer to adjacent parts and wiring
• Reduces risk of heat-related damage or premature wear on nearby parts
• Stops symptoms like excessive cabinet heat or visible degraded/burned insulation

• One insulating part as shown

• Disconnect power and water before starting any repair
• Inspect surrounding components and trim panels; removal of panels or assemblies may be required
• Handle carefully to avoid tearing or compressing the insulation; ensure correct orientation and fit

This cover is a replacement protective housing piece that shields internal components and wiring from debris and moisture, helping maintain safe operation and component longevity. It restores the appliance's original enclosure where the panel is damaged or missing. What it does:

• Protects electrical parts and connectors from dust, water, and physical contact
• Helps prevent short circuits and arcing caused by exposed wiring
• Reduces vibration-related noise by securing adjacent components
• Restores proper fit and finish to the appliance exterior

• One replacement cover as shown

• Disconnect power (unplug or switch off breaker) before beginning any work
• Use basic hand tools; avoid overtightening fasteners or forcing clips
• Inspect surrounding seals and wiring while panel is removed; replace damaged parts as needed

This replacement hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal. Replacing a worn clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place for reliable operation.

• Applies clamping force to hold a hose on a barb or stub connection
• Helps prevent leaks at hose joints
• Common symptoms: water leaking at a hose connection, hose slipping off, poor fill or drain performance
• Replace when the original is loose, corroded, distorted, or lost tension; also recommended when installing a new hose

• Disconnect power and shut off water supply before servicing
• Expect some residual water; protect the work area
• Note the clamp's position/orientation; use appropriate hand tools for the clamp style
• Ensure the hose is fully seated and clamp is secure; run a test cycle and check for leaks