Shu46c05uc Parts

This O-ring seals the NTC (negative temperature coefficient) temperature sensor where it inserts into the appliance. It restores a watertight seal at the sensor port to help prevent leaks and maintain reliable temperature-sensing performance.

• Provides a leak-tight seal between the NTC temperature sensor and its housing/tub/sump
• Helps prevent water seepage and moisture intrusion around the sensor opening
• Common symptoms of a failed seal: drips near the base, moisture in the leak tray, flattened/cracked ring, or a sensor that feels loose
• Good practice to replace when the NTC sensor is removed for service

• Disconnect power and shut off water supply before servicing
• Access the NTC sensor, remove the old O-ring, and clean mating surfaces
• Lightly moisten the new O-ring with water; seat it evenly to avoid pinching, then reinstall the sensor fully
• Run a brief test cycle and inspect for leaks

The Control Module Front Cover is an OEM part for Bosch dishwashers. This front cover protects the internal control board governing all dishwasher functions.

Causes of a bad control module front cover can include cracked or broken plastic from overtightening, damage due to impact or handling, or warping over time.

Symptoms of a bad control module front cover include:

• Lights and controls malfunctioning or not responding
• Water or debris entering the control area
• Loose or missing front cover exposing internal parts
• Damage allowing for short circuits or shock hazards

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This replacement foot is the leveling support at the base of your appliance. It helps set the height and keep the unit stable and level, reducing wobble, vibration, and noise for smoother, quieter operation.

• Supports the appliance base and provides solid floor contact
• Allows height/leveling adjustment as designed by the unit
• Helps correct rocking, vibration, walking, or door misalignment caused by an unlevel appliance
• Replace if the foot is cracked, missing, worn, or stripped and won't hold adjustment

• Disconnect power; shut off water supply if applicable
• Protect flooring and have a helper steady or move the unit
• Remove the damaged foot; install the new foot per the mounting style (threaded or push-in)
• Adjust height to level the cabinet and stability at all corners

Screw: 8-16 x 3/8 inch.

This genuine OEM part is a circulation pump motor for dishwashers. The circulation pump motor distributes water to the spray arm to allow the dishwasher to properly do its job. Over time, the circulation pump motor can become overworked to the point of becoming inoperable. Luckily, replacing the pump motor is not as difficult a job as it might seem. To begin the repair, turn off the power supply and shut off the water supply valve. Remove the screws that secure the lower access panel. Disconnect the water supply line from the inlet valve. Then proceed to remove the mounting screws from the junction box cover. Take note of the wires' orientation. Remove the screws that hold the bracket. Disconnect the drain hose from the sink or garbage disposal. Open the dishwasher door and remove the mounting screws. Pull the dishwasher away from the cabinet and unsnap the covers from the hinge ropes. Disconnect the ropes. Remove the screws securing the upper door panel. Carefully tilt the dishwasher back and detach the fill hose from its retaining clip disconnecting the hose from the sump. Uninstall the circulation pump and align the pump with the seal and sump. Tighten the clamp and transfer the wires from the old pump to the new one. Proceed to reinstall the panels that were uninstalled.This replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador dishwashers.

Replacement spray arm that restores water distribution for better rinse coverage and more even cleaning. Installs in the dishwasher tub to re-establish spray patterns and water flow lost to cracks or wear. What it does:

• Rotates and directs high-pressure jets of water to rinse and loosen food soils from dishes and cookware
• Restores proper spray coverage when the original arm is cracked, clogged, warped, or not spinning freely
• Helps reduce spots and missed areas by re-establishing even water distribution across racks
• Works with the dishwasher's pump and tubing to maintain normal wash performance

• Disconnect power and turn off the water supply before beginning any service
• Remove lower rack and any retaining clip or cap to access the spray arm; note orientation for reassembly
• Inspect and clear spray holes of debris before installing; ensure the arm spins freely after installation
• Do not overtighten mounting hardware; replace any damaged clips or seals for a secure fit

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

For mating terminal use WP94614.

For mating terminal use [AP31136300].

Color: light gray. Measures about 3 inches high by 2 inches deep.

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

This sump collects and channels dishwasher wash water into the wash pump, helping maintain proper drainage and reduce leaks at the tub-to-pump connection. Replace a cracked or damaged sump to restore correct water flow and sealing. What it does

• Directs wash water from the tub into the wash pump and drain system.
• Houses the pump inlet and seals the pump-to-tub interface.
• Prevents leaks by providing a secure seal between the tub and pump assembly.
• Common symptoms: pooling water in the tub, dishwasher not draining, leaks from the base, or unusual pump noise/vibration.

• Disconnect power and turn off the water supply before starting any repair.
• Handle carefully; inspect and replace any worn gaskets or seals when installing the new sump.
• Access typically requires removing lower access panels and the lower dish rack.
• After installation, test for leaks and proper drain operation before returning the appliance to normal use.

This is the right side hinge plate. For left side use 00298567.

This rear pump housing is the dishwasher's molded enclosure that supports the drain/pump assembly and channels wash and drain water. Replacing a damaged housing restores proper water flow and helps stop leaks. What it does:

• Houses and aligns the drain/pump components and motor coupling
• Channels water between sump, pump and drain lines to ensure proper draining
• Prevents leaks by sealing the pump assembly area when intact
• Can cause noisy pump operation or failure to drain if cracked or broken

• One rear pump housing

• Disconnect power and turn off water supply before starting; drain any standing water
• Inspect associated seals, gaskets, impeller and mounting hardware; replace if worn
• Handle carefully to avoid damaging mating surfaces; test for leaks after reassembly

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area