Shv46c Parts

This factory screw secures select Bosch/BSH appliance components. Use it to replace a missing or damaged fastener so panels, brackets, or trim stay tight and rattle-free during operation.

• Tightens and holds appliance parts such as panels, brackets, or trim in place
• Helps correct issues like loose or vibrating panels caused by a missing/stripped screw
• Maintains proper fitment after service or disassembly
• Torx T20 drive head helps resist cam-out during tightening

• Unplug power and shut off any water supply before servicing
• Use a T20 Torx driver; hand-start to avoid cross-threading
• Do not overtighten—snug to manufacturer torque guidance if available
• Replace any additional missing or damaged fasteners for even clamping

Small replacement O-ring that seals the dishwasher aqua sensor assembly to maintain a watertight seal and help ensure reliable sensor operation. Fits the sensor housing to reduce leaks and protect internal electronics. What it does:

• Seals the aqua/sensor housing to prevent water from escaping the sensor area
• Helps maintain accurate sensor readings by keeping the sensor dry and properly seated
• Commonly replaced when you see water pooling or dripping near the sensor assembly
• Used during aqua-sensor, pump, or housing repairs where the original seal is damaged

• Always disconnect power and turn off the water supply before starting repairs
• Replace the O-ring only when the sensor or housing is disassembled; inspect mating surfaces for damage or debris
• Ensure the O-ring is seated evenly in its groove before reassembly to avoid pinching or leaks

This is the right side hinge plate. For left side use 00298567.

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

This sump collects and channels dishwasher wash water into the wash pump, helping maintain proper drainage and reduce leaks at the tub-to-pump connection. Replace a cracked or damaged sump to restore correct water flow and sealing. What it does

• Directs wash water from the tub into the wash pump and drain system.
• Houses the pump inlet and seals the pump-to-tub interface.
• Prevents leaks by providing a secure seal between the tub and pump assembly.
• Common symptoms: pooling water in the tub, dishwasher not draining, leaks from the base, or unusual pump noise/vibration.

• Disconnect power and turn off the water supply before starting any repair.
• Handle carefully; inspect and replace any worn gaskets or seals when installing the new sump.
• Access typically requires removing lower access panels and the lower dish rack.
• After installation, test for leaks and proper drain operation before returning the appliance to normal use.

Bushing included. To order bushing separately use 00165296. This is the left side hinge. For right side hinge use 00263119.

This is the left side hinge plate. For right side use 00298570.

This electrical control switch completes or interrupts the power circuit that runs a specific appliance function, restoring on/off control for responsive operation and safer use. What it does:

• Acts as the user-activated or circuit-activated on/off control for a discrete function
• Restores power flow when the switch is made, allowing the associated component or cycle to run
• Common symptom: appliance function won't start or respond when the control is pressed or activated
• Common symptom: intermittent operation or no power to a given feature

• One switch

• Disconnect power to the appliance before attempting any service to prevent shock
• Access and replacement steps vary by model; follow the appliance service manual or schematic for safe disassembly
• Handle connectors carefully and confirm secure wiring/terminal seating after installation

The Tube Dishwasher is an OEM component for Bosch dishwashers. It is responsible for circulating water throughout critical spray arms during different cycles. 

Causes of a bad tube dishwasher can include mineral buildup reducing the tube diameter over time, physical damage from scraping dishware against the pipes, or wear from normal vibration/motion.

Symptoms of a bad tube dishwasher include:

• Incomplete spray coverage in hard-to-reach areas  
• Soft or spotty cleaning performance in certain sections
• Puddles or leaks at the tube installation points
• Dirty or stagnant water unable to circulate properly

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This clamp secures a wooden or custom exterior panel to the appliance door, restoring proper panel alignment and reducing rattling or looseness. Designed to match the OEM bracket location and fit. What it does:

• Holds the decorative wood panel firmly against the dishwasher door frame
• Prevents the panel from shifting, sagging, or vibrating during cycles
• Restores even door fit and helps maintain the door's seal and appearance
• Works at the bracket attachment point to stabilize panel-to-door connection

• Disconnect power to the appliance before beginning any work
• Remove the outer door panel per the service manual to access the clamp location
• Inspect surrounding clips and screws; replace any damaged fasteners for a secure fit

This sump clamp secures the dishwasher sump/drain assembly to the tub, keeping the seal and pump assembly held in place to prevent leaks and movement. It's a small but essential fastener for a watertight sump connection. What it does:

• Holds the sump/drain housing tightly against the tub to maintain a proper seal
• Prevents the sump assembly from shifting during operation, which can cause leaks or noise
• Helps stop water from leaking under the machine when the pump runs
• Supports proper alignment of the drain/pump components for reliable draining

• One sump clamp

• Disconnect power and water supply before starting any repair
• Access the sump area by removing the lower access panel or toe kick and tilting the machine as needed
• Inspect the sump seal/gasket and replace if cracked or damaged when replacing the clamp
• Tighten clip until secure but avoid forcing or deforming the sump housing; test for leaks after reassembly

This shaft for the float switch is the replacement shaft that secures and guides the dishwasher float to accurately detect water level, helping the appliance fill and shut off properly. Direct-fit design replaces the worn or broken float shaft. What it does

• Guides the float so the level-sensing switch can detect low or high water levels.
• Prevents overfilling by ensuring the float actuates the water-level switch reliably.
• Commonly replaces a cracked, bent or missing shaft that causes inconsistent fill, continuous filling, or water-level errors.

• One replacement float switch shaft.

• Disconnect power to the appliance before starting any repair.
• Remove the access panels and float assembly per your model's service instructions to reach the shaft.
• Inspect the float and switch for damage; replace only the failed components as needed.
• Reassemble carefully and test fill/stop operation before returning the appliance to service.

This actuator assembly operates the dishwasher's top rack mechanisms to enable proper rack movement and adjustment. Replacing a worn or broken top-rack actuator restores reliable rack travel and prevents misalignment during cycles. What it does:

• Drives or releases the top rack adjustment/advance mechanism so the rack moves and positions correctly.
• Stops binding or uneven rack travel caused by a failed actuator.
• Helps prevent scraping, jamming, or unusual noises from the top rack area when loading or during cycles.
• Works as the mechanical linkage between the rack and the dishwasher's internal drive components.

• Disconnect power and water supply before starting any repair.
• Follow OEM disassembly steps for access—usually involves removing the top rack and inner paneling to reach the actuator.
• Inspect surrounding mounts and linkages; replace any damaged clips or screws to ensure secure operation.