Shv4803uc Parts

Color: light gray. Measures about 3 inches high by 2 inches deep.

This sump collects and channels dishwasher wash water into the wash pump, helping maintain proper drainage and reduce leaks at the tub-to-pump connection. Replace a cracked or damaged sump to restore correct water flow and sealing. What it does

• Directs wash water from the tub into the wash pump and drain system.
• Houses the pump inlet and seals the pump-to-tub interface.
• Prevents leaks by providing a secure seal between the tub and pump assembly.
• Common symptoms: pooling water in the tub, dishwasher not draining, leaks from the base, or unusual pump noise/vibration.

• Disconnect power and turn off the water supply before starting any repair.
• Handle carefully; inspect and replace any worn gaskets or seals when installing the new sump.
• Access typically requires removing lower access panels and the lower dish rack.
• After installation, test for leaks and proper drain operation before returning the appliance to normal use.

This is the right side hinge plate. For left side use 00298567.

This rear pump housing is the dishwasher's molded enclosure that supports the drain/pump assembly and channels wash and drain water. Replacing a damaged housing restores proper water flow and helps stop leaks. What it does:

• Houses and aligns the drain/pump components and motor coupling
• Channels water between sump, pump and drain lines to ensure proper draining
• Prevents leaks by sealing the pump assembly area when intact
• Can cause noisy pump operation or failure to drain if cracked or broken

• One rear pump housing

• Disconnect power and turn off water supply before starting; drain any standing water
• Inspect associated seals, gaskets, impeller and mounting hardware; replace if worn
• Handle carefully to avoid damaging mating surfaces; test for leaks after reassembly

Bushing included. To order bushing separately use 00165296. This is the left side hinge. For right side hinge use 00263119.

An integrated door switch for dishwashers that senses when the door is closed and allows the machine to start. Replacing a worn or damaged switch restores normal operation and helps prevent cycles from running with an open door. What it does:

• Detects door-closed position and tells the control board the door is secure
• Enables the dishwasher to start cycles only when the door is properly latched
• Prevents operation or pauses cycles if the door is open or not fully closed
• Common symptom: dishwasher won't start or stops mid-cycle when the door is opened

• Disconnect power to the appliance before attempting any service.
• Access typically requires removing the inner door panel or toe-kick; handle the door carefully to avoid damage.
• Replace the switch and reconnect wiring exactly as removed; ensure connectors are fully seated.
• After installation, restore power and ensure the door registers closed and the unit starts normally.

This is the left side hinge plate. For right side use 00298570.

This clamp secures a wooden or custom exterior panel to the appliance door, restoring proper panel alignment and reducing rattling or looseness. Designed to match the OEM bracket location and fit. What it does:

• Holds the decorative wood panel firmly against the dishwasher door frame
• Prevents the panel from shifting, sagging, or vibrating during cycles
• Restores even door fit and helps maintain the door's seal and appearance
• Works at the bracket attachment point to stabilize panel-to-door connection

• Disconnect power to the appliance before beginning any work
• Remove the outer door panel per the service manual to access the clamp location
• Inspect surrounding clips and screws; replace any damaged fasteners for a secure fit

This sump clamp secures the dishwasher sump/drain assembly to the tub, keeping the seal and pump assembly held in place to prevent leaks and movement. It's a small but essential fastener for a watertight sump connection. What it does:

• Holds the sump/drain housing tightly against the tub to maintain a proper seal
• Prevents the sump assembly from shifting during operation, which can cause leaks or noise
• Helps stop water from leaking under the machine when the pump runs
• Supports proper alignment of the drain/pump components for reliable draining

• One sump clamp

• Disconnect power and water supply before starting any repair
• Access the sump area by removing the lower access panel or toe kick and tilting the machine as needed
• Inspect the sump seal/gasket and replace if cracked or damaged when replacing the clamp
• Tighten clip until secure but avoid forcing or deforming the sump housing; test for leaks after reassembly

This shaft for the float switch is the replacement shaft that secures and guides the dishwasher float to accurately detect water level, helping the appliance fill and shut off properly. Direct-fit design replaces the worn or broken float shaft. What it does

• Guides the float so the level-sensing switch can detect low or high water levels.
• Prevents overfilling by ensuring the float actuates the water-level switch reliably.
• Commonly replaces a cracked, bent or missing shaft that causes inconsistent fill, continuous filling, or water-level errors.

• One replacement float switch shaft.

• Disconnect power to the appliance before starting any repair.
• Remove the access panels and float assembly per your model's service instructions to reach the shaft.
• Inspect the float and switch for damage; replace only the failed components as needed.
• Reassemble carefully and test fill/stop operation before returning the appliance to service.

This actuator assembly operates the dishwasher's top rack mechanisms to enable proper rack movement and adjustment. Replacing a worn or broken top-rack actuator restores reliable rack travel and prevents misalignment during cycles. What it does:

• Drives or releases the top rack adjustment/advance mechanism so the rack moves and positions correctly.
• Stops binding or uneven rack travel caused by a failed actuator.
• Helps prevent scraping, jamming, or unusual noises from the top rack area when loading or during cycles.
• Works as the mechanical linkage between the rack and the dishwasher's internal drive components.

• Disconnect power and water supply before starting any repair.
• Follow OEM disassembly steps for access—usually involves removing the top rack and inner paneling to reach the actuator.
• Inspect surrounding mounts and linkages; replace any damaged clips or screws to ensure secure operation.

A small replacement magnet plunger that secures top-rack components and helps maintain proper alignment and operation. Use this part when the top-rack magnet is damaged, loose, or no longer holds as intended. What it does:

• Provides magnetic retention for top-rack assemblies and related components
• Restores proper alignment and engagement of the top-rack magnet interface
• Can reduce rattling or shifting of the top rack caused by a worn or missing magnet
• May be needed if the original plunger is cracked, corroded, or detached

• One magnet plunger

• Designed for top-rack application only; confirm correct orientation before installing
• Turn off power to the appliance and follow all safety guidelines before servicing
• Use basic hand tools; avoid forcing components to prevent breakage