Shv863wd3n Parts

This electronic control unit is the appliance's main circuit board, directing programs, user inputs, and power to components. Replacing a failed board restores responsive controls and consistent cycle operation when the original is damaged or malfunctioning.

• Interprets user inputs and sensor signals to run the selected program
• Controls timing and power delivery to motors, valves, heaters, and indicators
• Stores operating logic and coordinates cycle steps
• Typical failure symptoms include unresponsive controls, won't start or advance, intermittent shutdown, error codes, or flickering lights

• Disconnect power before servicing; also shut off gas
• Use ESD protection; handle the PCB by the edges to avoid static damage
• Photograph wiring and move connectors one at a time; secure seating
• Location and setup vary by model; for any required programming or calibration

This sump screw secures the dishwasher's sump or sump cover to the tub, keeping the assembly tight and leak-resistant. Replace a missing, stripped, or damaged screw to restore a proper seal and stable mounting.

• Fastens the sump or sump cover to the dishwasher tub
• Helps maintain a watertight seal to reduce leaks
• Keeps filter/sump components aligned and secure
• Replaces missing, stripped, or damaged hardware
• Helps address leaks or rattling around the sump area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack and filters to access the sump area
• Ensure mating surfaces and seals are clean and properly seated
• Tighten snugly by hand; do not overtighten to avoid stripping

The Screw is an OEM replacement part for Bosch dishwashers. Hundreds of screws hold the appliance panels and internal mechanisms securely in place. Consistent, protective enclosures ensure long-lasting performance.

Causes of a bad screw can include stripped threads from repeated tightening/loosening during repairs. Corrosion posing integrity risks may develop if water penetrates screw heads over time. 

Symptoms of a bad screw include: 

• Panels or racks that rattle or come loose during operation
• Gaps appear that allow residual moisture to seep within
• Internal components shifting position from the original assembly
• Loose wiring susceptible to abrasion posing electrical hazards

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Divertor Motor is an OEM part for Bosch dishwashers.  This part controls the direction of water flow within the unit. This motor directs the water to different spray arms based on the selected wash cycle, ensuring efficient cleaning by optimizing water usage and spray intensity. 

Causes of damage to the divertor motor can include regular wear and tear, exposure to water and detergent over time, and electrical issues such as wiring problems or faults in the control board.

Symptoms of a failing Divertor Motor include:

• Inadequate water distribution during cycles, which can lead to uneven cleaning results.
• The dishwasher making unusual noises, such as humming or grinding, which may indicate a struggle in the motor function.
• Certain wash zones receiving little to no water, affecting the appliance's overall performance.
• Error codes displayed on the dishwasher panel that relate to water circulation problems.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Cup Rack is an OEM part for Bosch dishwashers. It is designed to fit inside the dishwasher tub and provide storage for cups, mugs, and other drinking vessels during the wash cycle.

Causes of a bad cup rack can include broken or missing prongs, cracks in the plastic that compromise stability, or difficulties with the rack sliding smoothly in and out of the tub.

Symptoms of a bad cup rack include:

• Cups and mugs not drying properly or falling over during the cycle
• Difficulty loading and removing cups from the rack
• Excessive noise or vibration coming from the cup rack area
• Inability to secure the cup rack fully inside the tub

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This protective cover sheet mounts to the appliance's frame to shield and support nearby components. Replacing a damaged or missing panel helps keep wiring and mechanisms protected and securely mounted, reducing vibration and preventing premature wear.

• Shields internal components from debris, moisture, and accidental contact
• Helps maintain proper alignment and support of adjacent assemblies
• Can reduce rattling or vibration when correctly secured
• Replace if bent, cracked, corroded, or missing

• Disconnect power (and water supply if applicable) before servicing
• Wear cut-resistant gloves; panel edges can be sharp
• Note and retain original fasteners/clips for reuse
• Route wires and seals carefully to avoid pinching; align panel before tightening fasteners

This support is a factory replacement component that holds and stabilizes a specific part within your appliance so it stays aligned and secure. Replacing a cracked or missing support restores proper fit and helps prevent noise or binding.

• Provides structural support and alignment for the designated component
• Keeps parts seated securely to minimize movement and vibration during use
• A damaged or missing support can cause looseness, rattling, sagging, or misalignment
• Restores proper fit and function when the original is cracked, warped, or broken

• Disconnect power and shut off any gas/water supplies before servicing
• Refer to your model's parts diagram to identify location and orientation
• Install using the appliance's existing screws or clips; avoid overtightening to prevent damage
• Wear cut-resistant gloves; beware of sharp edges and pinch points

This lock clamp secures an appliance component or assembly so it stays properly seated during operation. Replacing a worn or missing clamp helps restore a stable, rattle-free fit and reliable performance. What it does:

• Holds mating parts together to prevent shifting or vibration
• Helps maintain correct alignment of the secured component
• Can resolve issues where a part won't stay attached or seated
• Restore normal operation when the original clamp is broken or missing

• One lock clamp

• Disconnect power (and shut off water/gas if applicable) before servicing
• Note the clamp's original orientation; take a photo to aid reassembly
• Seat the component fully, then engage the clamp securely without over-stressing it
• Reassemble and test for a firm, stable fit before returning the appliance to service

This replacement spring restores proper tension in the specific mechanism it supports, helping the connected component operate smoothly. A worn or broken spring can cause weak action, poor latching, or parts that won't return or stay in position.

• Provides controlled tension/return force for moving parts per your model's design
• Helps doors, lids, latches, or dispenser mechanisms open/close or release reliably
• Symptoms of failure can include weak or uneven tension, components not staying shut/open, or sluggish operation
• Replace if the spring is stretched, broken, deformed, corroded, or missing

• Disconnect power and shut off water supply before servicing
• Note the spring's orientation and anchor points; take a photo for reference
• Use needle-nose pliers for removal/installation and avoid over-stretching
• If your model uses paired springs, replace both to maintain balanced tension

This temperature sensor (NTC) monitors wash temperature and reports it to the control so the cycle heats and advances correctly. Replacing a faulty sensor can restore proper cleaning performance and normal cycle times. What it does:

• Measures water temperature and sends resistance changes (NTC) to the control
• Helps the control regulate heating and cycle progression
• Failure symptoms can include no/insufficient heat, extended cycles, or poor drying
• May trigger a temperature-sensor fault (e.g., E11 on some models)

• 1 temperature sensor

• Disconnect power and turn off water supply before servicing
• Access is typically at the sump/heat-pump area; remove the toe-kick/lower panel as needed
• Expect some residual water; place a towel or tray to catch drips
• Ensure the sensor seats fully and the seal is in good condition to prevent leaks

The Spray Head is an OEM replacement part for Bosch dishwashers. It directs pressurized water along the dish racks, targeting every inch of dishware and cookware. Consistent coverage cleans thoroughly without waste.   

Symptoms of a bad spray head can include clogged nozzles, inconsistent patterns, or spray heads that do not oscillate and rotate properly through cycles. Mineral deposits pose blockage risks over time.

Causes of a bad spray head include:

• Uneven or skipped areas of spray coverage inside the machine
• Rotating/oscillating mechanisms that jam or continuously stick  
• Nozzles fully or partially blocked reducing water pressure
• Head assembly detaching from water tub wall or bracket

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Frame is an OEM part for Bosch dishwashers that provides support and organization for your cutlery, offering a designated space for your forks, knives, spoons, and other utensils. 

A bad frame can occur due to wear and tear, accidental damage, or exposure to harsh chemicals. Signs of a faulty frame include cracks, broken sections, or difficulty in smoothly sliding the drawer in and out.

Symptoms of a bad frame include:

• Cracks or broken sections in the frame 
• Difficulty in sliding the cutlery drawer in and out
• Unorganized or unstable storage of cutlery 

Replace your damaged or worn-out frame with this genuine OEM Bosch part to restore your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

The Handle is an OEM part for Bosch dishwashers. It provides the surface for securely grasping and maneuvering the dishwasher door during opening and closing. 

Causes of a bad handle can include wear and tear from ongoing grasping motions. Repeated lifting and adjusting of the door places stress on handle components over time.

Symptoms of a bad handle include:

• Looseness, wobbling or detachment from the door assembly
• Sharp edges, cracks or splits compromising a firm grip
• Reduced ability to precisely guide the door into position

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This replacement holder secures internal components in place to maintain proper alignment and reduce movement-related noise and wear. Use it when the original holder is cracked, deformed, or no longer holds parts firmly. What it does:

• Secures and supports internal assemblies to keep components correctly positioned.
• Reduces rattling, vibration and movement that can occur from loose parts.
• Replacing a worn or broken holder can prevent parts from shifting and causing intermittent operation.
• Use when the existing holder is visibly damaged, cracked, or fails to hold components tightly.

• Always disconnect power (and water, if applicable) before accessing the appliance.
• Remove surrounding panels, racks, or trim as needed for clear access.
• Reinstall using the original fasteners or clips; ensure correct orientation and secure fit without forcing parts.

This factory screw secures select Bosch/BSH appliance components. Use it to replace a missing or damaged fastener so panels, brackets, or trim stay tight and rattle-free during operation.

• Tightens and holds appliance parts such as panels, brackets, or trim in place
• Helps correct issues like loose or vibrating panels caused by a missing/stripped screw
• Maintains proper fitment after service or disassembly
• Torx T20 drive head helps resist cam-out during tightening

• Unplug power and shut off any water supply before servicing
• Use a T20 Torx driver; hand-start to avoid cross-threading
• Do not overtighten—snug to manufacturer torque guidance if available
• Replace any additional missing or damaged fasteners for even clamping

This holder is the mounting piece that secures a specific component inside your appliance. Replacing a cracked or missing holder restores proper support and alignment so the assembly stays stable and works as designed.

• Secures and supports the designated part in place
• Maintains alignment to help prevent vibration or rubbing
• A damaged holder can lead to loose or misaligned components
• Common symptoms: cracked/broken plastic, missing tabs, or the part no longer staying clipped/anchored

• Disconnect power and shut off water/gas before servicing
• Refer to your model's parts diagram for exact location and orientation
• Reuse original screws/clips/seals if they are not supplied with the replacement
• Do not overtighten fasteners into plastic; hand-snug to avoid stripping