Shv863wd3n Parts

The Leveling Leg is an OEM component specifically designed for Bosch dishwashers. This leg works to stabilize and balance the dishwasher evenly on any floor surface. 

The leveling leg is responsible for ensuring the dishwasher remains level during operation. Proper leveling is crucial for preventing excess vibration or noise, as well as allowing the dishwasher door to align correctly. 

Symptoms of a bad leveling leg can include:

• The dishwasher rocking or shuffling across the floor over time
• Excessive vibration or noise during wash cycles  
• The dishwasher door not closing or sealing properly
• Difficulty leveling the dishwasher 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers.

The Installation Set is an OEM part for Bosch brand dishwashers. It includes all the necessary mounting brackets and hardware required to securely install the dishwasher into the cabinetry cavity beneath the kitchen counter. 

Symptoms of a bad mounting set include:

• Loose fit of the dishwasher in the opening that allows side-to-side movement 
• Visible gaps around the perimeter of the unit once installed
• Sagging or inability to fully open or close the dishwasher door

Causes of a bad mounting set can include broken mounting brackets, corroded or damaged hardware, or missing screws, washers, or fittings that compromise a tight mounting installation. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers.
 

The Indicator Light is an OEM part for Bosch dishwashers. It serves as a visual cue, providing important status updates and notifications related to the dishwasher's operation.

Causes of a malfunctioning Indicator Light can stem from issues with the control board or wiring harness that powers the light, or the light itself burning out due to age or electrical surges.

Symptoms of a bad Indicator Light include:

• The light not illuminating at all, even when it should be on
• Flickering or dimming of the light during operation
• The wrong indicator light turning on or staying on inappropriately

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This factory fastener secures panels, brackets, and internal components in your appliance. Replacing a missing or damaged screw restores a snug fit, reduces vibration and rattles, and keeps assemblies properly aligned during service or reassembly.

• Anchors panels, trim, and internal parts to the appliance frame or subassemblies
• Helps prevent vibration, buzzing, and loose or shifting components
• Ideal replacement for lost, stripped, or corroded hardware
• Common symptoms include loose panels, gaps, rattling noises, or parts that won't stay secured

• Disconnect power and shut off water or gas before servicing
• Match this screw to the original and replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; use the correct driver and do not overtighten
• Inspect the mating clip/insert; replace if stripped or damaged for a secure hold

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

Replacement push-button for the appliance control panel that restores tactile action and appearance. Use when the original button is cracked, worn, stuck, or missing to recover normal button operation. What it does

• Acts as the visible actuator on the control panel, engaging the underlying switch or membrane.
• Restores button feel and appearance so commands register correctly when the original is damaged.
• Useful when a button is cracked, chipped, stuck, or missing and won't return or press reliably.
• Does not include internal switch or electronics unless otherwise specified on the product page.

• Always unplug the appliance or disconnect power at the breaker before attempting any repair.
• Remove the control console or trim to access the button; keep track of small screws and clips.
• Gently disengage plastic tabs or clips to remove the old button; avoid forcing parts to prevent breaking surrounding trim.
• Test button function before reassembling the console; if the underlying switch still fails, further disassembly or a switch replacement may be required.

This replacement worm gear is a small plastic drive gear that transmits rotational motion between the motor and driven components, restoring normal gear-driven movement and reducing slipping or grinding. What it does:

• Transfers torque from the motor to the mating gear or gearbox for proper mechanical operation
• Replaces worn, stripped, or damaged worm teeth that cause slipping or loss of drive
• Stops grinding, clicking, or intermittent movement when the gear is the fault
• Helps restore smooth, consistent operation of the driven mechanism when installed correctly

• One worm gear

• Disconnect power to the appliance before beginning any repair
• Inspect mating gears and shafts for wear; replace worn parts to prevent repeat failure
• Use OEM-approved lubricant only where specified; do not force or overtighten mating components

This holder secures internal components to keep assemblies aligned and stable, reducing vibration and wear. It's a simple replacement that restores proper fit where a broken or missing clip causes loose panels or noisy operation. What it does

• Secures and aligns panels or wiring harnesses inside the appliance
• Prevents rattling, vibration, and misalignment caused by damaged or missing clips
• Helps maintain proper component spacing to avoid wear or interference
• Restores secure attachment after breakage or plastic fatigue

• Disconnect power and water before starting any repair
• Remove access panels or trim to reach the damaged clip—keep fasteners organized
• Press or snap the holder into place; replace any broken tabs before reassembling
• If plastic anchors are damaged, replace them with matching OEM clips

This replacement hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal. Replacing a worn clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place for reliable operation.

• Applies clamping force to hold a hose on a barb or stub connection
• Helps prevent leaks at hose joints
• Common symptoms: water leaking at a hose connection, hose slipping off, poor fill or drain performance
• Replace when the original is loose, corroded, distorted, or lost tension; also recommended when installing a new hose

• Disconnect power and shut off water supply before servicing
• Expect some residual water; protect the work area
• Note the clamp's position/orientation; use appropriate hand tools for the clamp style
• Ensure the hose is fully seated and clamp is secure; run a test cycle and check for leaks

This insulating part installs in the specified location to help reduce heat transfer between internal spaces and exterior panels. Replacing a worn or missing insulator helps protect nearby components and maintain proper operating temperatures.

• Provides a thermal barrier to limit heat transfer to surrounding panels and wiring
• Helps prevent scorching or heat damage to adjacent components
• Restores proper insulation where the original has deteriorated or is missing
• Common signs of failure: visible damage or fraying, burnt odor, or unusually hot exterior areas

• Disconnect power and allow the appliance to cool completely before servicing
• Wear gloves and eye protection; insulation fibers can irritate skin and eyes
• Match the original orientation/placement; do not over-compress the material
• Keep insulation clear of vents, heating elements, fans, and moving parts

This suspension damper stabilizes the tub/drum by absorbing movement and vibration during operation. Replacing a worn damper helps reduce shaking and noise, improving spin performance and overall machine stability. What it does:

• Absorbs and controls tub/drum movement to reduce vibration and noise
• Helps prevent banging, "walking," or out-of-balance shutdowns during spin
• Can address excessive shaking, rattling, and longer spin times
• Restores smoother, more controlled operation when the original damper is worn

• One suspension damper

• Disconnect power and turn off water supply before servicing
• Access location varies by model; support the tub/drum to relieve load before removal
• Note orientation and reuse existing mounting hardware if new fasteners aren't provided
• After installation, re-level the appliance and run a test cycle to verify stability

This holder/retainer secures its mating part in the correct position inside the appliance, preventing unwanted movement and ensuring consistent operation. Replace a cracked or missing holder to restore a solid, factory fit and reliable performance.

• Supports and locks the attached component or rack/accessory in place
• Helps prevent vibration, rattling, or misalignment during use
• Typical signs of failure: broken tabs, visible cracks, looseness, or the part no longer staying secured
• Restores proper positioning of the related component for consistent function

• Disconnect power at the breaker; shut off water supply if applicable
• Note the holder's orientation; take a photo before removal
• Reuse existing screws/fasteners if none are supplied with the part
• Seat fully until it clicks/locks; do not overtighten into plastic

This outer door panel replaces the exterior shell of a dishwasher door to restore appearance and protect internal components. It provides a clean, finished surface and helps maintain proper door alignment and sealing. What it does:

• Replaces a dented, scratched, or corroded exterior door surface to improve appliance appearance.
• Protects internal door components from damage and moisture exposure.
• Helps the door close and latch properly by restoring the correct outer panel alignment.
• Reduces drafts or gaps caused by a damaged outer shell that can affect door sealing.

• Disconnect power and shut off water before starting any repair.
• Keep track of all screws, clips, and insulation layers during disassembly for correct reassembly.
• Use appropriate tools and avoid bending the panel when aligning and fastening.

This push button set replaces the worn or damaged control buttons on compatible Bosch appliance control panels, restoring tactile feedback and reliable user input for cycle selection and control functions. What it does:

• Replaces broken, cracked, or missing push buttons that prevent normal panel operation
• Restores proper tactile feel for selecting cycles, options, and other controls
• Helps eliminate buttons that stick, don't depress fully, or fail to register presses
• Improves appearance of the control panel when original buttons are faded or discolored

• Disconnect power to the appliance before beginning any repair to avoid shock or damage
• Typically installs from the front of the control panel; may require removing the outer panel or trim
• Handle buttons gently—do not force; align clips or posts before pressing into place