Shx7er55uc Parts

This genuine water inlet routes household water into the appliance's fill system, helping ensure consistent water delivery and a secure, leak-resistant connection. Replacing a worn or damaged inlet restores proper filling performance and helps prevent leaks at the entry point. What it does:

• Connects the supply line to the unit and directs water into the fill system
• Helps maintain a watertight seal at the water entry connection
• Supports proper fill by working with the appliance's control and fill components
• Common symptoms: no or slow fill, dripping/leak at the inlet connection, visible cracks or mineral buildup on the fitting

• 1 water inlet

• Disconnect power and turn off the water supply before servicing
• Place a towel or pan to catch residual water when removing the old part
• Note the orientation; reinstall existing seals/clips in their original positions if applicable
• Tighten fittings snugly without overtightening; restore water and check for leaks before use

This temperature sensor (NTC) monitors wash temperature and reports it to the control so the cycle heats and advances correctly. Replacing a faulty sensor can restore proper cleaning performance and normal cycle times. What it does:

• Measures water temperature and sends resistance changes (NTC) to the control
• Helps the control regulate heating and cycle progression
• Failure symptoms can include no/insufficient heat, extended cycles, or poor drying
• May trigger a temperature-sensor fault (e.g., E11 on some models)

• 1 temperature sensor

• Disconnect power and turn off water supply before servicing
• Access is typically at the sump/heat-pump area; remove the toe-kick/lower panel as needed
• Expect some residual water; place a towel or tray to catch drips
• Ensure the sensor seats fully and the seal is in good condition to prevent leaks

This genuine replacement bearing supports the washer drum for smooth, stable rotation and helps reduce noise and vibration caused by worn or damaged bearings. Restores proper drum alignment for quieter operation. What it does:

• Supports the inner drum so it spins smoothly and stays aligned
• Reduces grinding, rumbling, squeaking or knocking noises from the drum
• Helps prevent excessive drum wobble that can damage seals or the tub
• Used when worn bearings cause rough rotation, metal-on-metal noise, or visible drum play

• Disconnect power (and water if applicable) before starting any repair
• Replacing this bearing typically requires partial disassembly of the washer/drum assembly and specialty tools
• Inspect shaft/hub, seals, and surrounding components for wear and replace if damaged

The Frame is an OEM part for Bosch dishwashers that provides support and organization for your cutlery, offering a designated space for your forks, knives, spoons, and other utensils. 

A bad frame can occur due to wear and tear, accidental damage, or exposure to harsh chemicals. Signs of a faulty frame include cracks, broken sections, or difficulty in smoothly sliding the drawer in and out.

Symptoms of a bad frame include:

• Cracks or broken sections in the frame 
• Difficulty in sliding the cutlery drawer in and out
• Unorganized or unstable storage of cutlery 

Replace your damaged or worn-out frame with this genuine OEM Bosch part to restore your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

The Levelling Foot is an OEM replacement part designed specifically for Bosch dishwashers. It works to properly position and stabilize the appliance for balanced and smooth operation. Causes of a bad levelling leg/foot can include general wear and tear over time. 

Symptoms of a bad levelling foot include: 

• An unbalanced or unstable dishwasher during use
• Rocking or shifting of the unit on an uneven surface 

This genuine OEM Bosch part restores proper alignment and support of the dishwasher to ensure optimal performance and noise reduction. This Bosch part can also be used on Thermador and Gaggenau appliances.

This factory bearing supports a rotating component inside your appliance, reducing friction so it turns smoothly and quietly. Replacing a worn bearing helps restore proper motion and can reduce noise and wear in the related assembly. What it does:

• Provides low-friction support for a rotating shaft or arm
• Helps maintain smooth, aligned rotation
• Common wear signs: grinding/squealing noises, wobble or excess play, rough/sticking rotation, or visible damage
• A failed bearing can accelerate wear on connected parts

• 1 bearing

• Disconnect power; shut off water or gas before servicing
• Note orientation and any spacers/clips before removal; transfer in the same order
• Inspect mating seals, clips, or shafts and replace if worn
• Do not lubricate unless specified by the manufacturer; keep contact surfaces clean

The Indicator Light is an OEM part for Bosch dishwashers. It serves as a visual cue, providing important status updates and notifications related to the dishwasher's operation.

Causes of a malfunctioning Indicator Light can stem from issues with the control board or wiring harness that powers the light, or the light itself burning out due to age or electrical surges.

Symptoms of a bad Indicator Light include:

• The light not illuminating at all, even when it should be on
• Flickering or dimming of the light during operation
• The wrong indicator light turning on or staying on inappropriately

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This replacement foot is the leveling support at the base of your appliance. It helps set the height and keep the unit stable and level, reducing wobble, vibration, and noise for smoother, quieter operation.

• Supports the appliance base and provides solid floor contact
• Allows height/leveling adjustment as designed by the unit
• Helps correct rocking, vibration, walking, or door misalignment caused by an unlevel appliance
• Replace if the foot is cracked, missing, worn, or stripped and won't hold adjustment

• Disconnect power; shut off water supply if applicable
• Protect flooring and have a helper steady or move the unit
• Remove the damaged foot; install the new foot per the mounting style (threaded or push-in)
• Adjust height to level the cabinet and stability at all corners

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

The Fine Filter is an OEM part for Bosch dishwashers. It is designed to trap small food particles and debris before they can clog other areas of the dishwasher.

The fine filter is positioned inside the dishwasher tub and spray arms to act as a preliminary filter. It helps keep the wash and rinse zones free of obstructions to allow for the best cleaning performance.

Causes of a faulty fine filter are normal product usage over time, accumulation of stubborn food or mineral deposits, and occasional damage from sharp dish edges

Symptoms of a bad fine filter include:
Buildup of muck or grime that cannot be cleaned
Torn or damaged mesh that no longer traps particles
Improper drainage or water not circulating as it should
This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Dishwasher Hinge Lever is an OEM replacement part for Bosch dishwashers. This hinge lever is crucial for the operation of the dishwasher door, supporting smooth movement as it opens and closes. It works alongside the door springs to provide balanced tension, ensuring that the door stays securely in place when opened or closed. 

Over time, hinge levers may wear out due to regular use, strain from overloading the door, or corrosion from prolonged exposure to moisture. A damaged hinge lever can disrupt the door’s movement, leading to issues with opening, closing, or improper sealing of the dishwasher door.

Symptoms of a bad Dishwasher Hinge Lever include:

• Difficulty opening or closing the dishwasher door
• The door dropping open without resistance
• A loose or sagging door that won’t stay securely in place
• Unusual noises when moving the door 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Replacement push-button for the appliance control panel that restores tactile action and appearance. Use when the original button is cracked, worn, stuck, or missing to recover normal button operation. What it does

• Acts as the visible actuator on the control panel, engaging the underlying switch or membrane.
• Restores button feel and appearance so commands register correctly when the original is damaged.
• Useful when a button is cracked, chipped, stuck, or missing and won't return or press reliably.
• Does not include internal switch or electronics unless otherwise specified on the product page.

• Always unplug the appliance or disconnect power at the breaker before attempting any repair.
• Remove the control console or trim to access the button; keep track of small screws and clips.
• Gently disengage plastic tabs or clips to remove the old button; avoid forcing parts to prevent breaking surrounding trim.
• Test button function before reassembling the console; if the underlying switch still fails, further disassembly or a switch replacement may be required.

Replacement door hinge that restores proper door alignment and smooth opening/closing for compatible Bosch appliances. Simple, direct support for the door pivot to reduce sagging, uneven closing, and noisy operation. What it does:

• Supports the appliance door pivot and maintains correct door alignment during use.
• Helps stop door sagging, uneven gaps, and doors that don't close or latch reliably.
• Restores smooth opening and closing and reduces hinge-related noise.
• Works as the mechanical pivot/connection between the door and cabinet frame.

• Turn off power and disconnect the appliance (and water supply if applicable) before starting any repair.
• Support the door while removing/installing the hinge to prevent damage or injury.
• Use the original mounting hardware or manufacturer-recommended fasteners; tighten securely but avoid overtightening.
• After installation, check door alignment and operation; adjust as needed per manufacturer instructions.

Spring-style hose clamp that secures flexible water hoses to fittings on select appliances, helping maintain a leak-tight connection at hose joints. Keeps hoses seated to reduce leaks and ensure reliable water flow. What it does:

• Holds flexible inlet, drain, or circulation hoses tightly on barbed fittings and nipples.
• Prevents leaks and water loss at hose connections by maintaining steady clamp pressure.
• Common signs it needs replacement: dripping or pooling near hose connections, a loose or wobbly hose, or visible clamp corrosion or deformation.
• Small, inexpensive part that restores a secure hose connection when the original clamp has failed.

• Always disconnect power and shut off the water supply before servicing appliance plumbing.
• For spring-style clamps, use pliers to open the clamp, position it over the hose, and release slowly so it seats properly; ensure the hose is fully pushed onto the fitting.
• Inspect the hose and fitting for damage; replace the hose if cracked or excessively worn before installing a new clamp.
• Wear eye protection when compressing or releasing spring clamps to avoid injury from sudden release.

Trim strip that finishes and protects an appliance edge while helping hold panels or seals in place. Replacing a damaged strip restores a clean fit and reduces gaps, vibration, and exposure to sharp edges. What it does:

• Covers and protects exposed metal or panel edges — symptom: visible edge damage or chipping.
• Helps secure panel or seal edges to maintain proper fit — symptom: loose or gapped panels.
• Reduces noise and vibration between parts — symptom: rattling or buzzing during operation.
• Helps limit moisture or debris intrusion where panels meet — symptom: dampness or dirt accumulation along seams.

• Disconnect power to the appliance before starting any work; follow lockout/tagout if applicable.
• Remove the old strip and any adhesive or fasteners; inspect the mounting surface for damage.
• Align the replacement strip, then press or snap it into position; some applications may require clips or screws.