Spe53u55uc/42 Parts

This fixing kit is a replacement set of mounting hardware used to secure appliance components or panels. It restores a tight, aligned fit when original fasteners are lost, stripped, or damaged. What it does:

• Secures panels or components to the appliance frame
• Replaces missing or worn hardware to restore proper fastening
• Helps correct looseness, rattling, or minor misalignment
• Supports proper fit after service or part replacement

• One fixing kit

• Disconnect power (and shut off water/gas if applicable) before servicing
• Match each fastener to the original location and orientation
• Hand-start threads to avoid cross-threading; tighten evenly without overtightening
• Refer to the model's service documentation for any specified sequence or torque

This genuine water inlet routes household water into the appliance's fill system, helping ensure consistent water delivery and a secure, leak-resistant connection. Replacing a worn or damaged inlet restores proper filling performance and helps prevent leaks at the entry point. What it does:

• Connects the supply line to the unit and directs water into the fill system
• Helps maintain a watertight seal at the water entry connection
• Supports proper fill by working with the appliance's control and fill components
• Common symptoms: no or slow fill, dripping/leak at the inlet connection, visible cracks or mineral buildup on the fitting

• 1 water inlet

• Disconnect power and turn off the water supply before servicing
• Place a towel or pan to catch residual water when removing the old part
• Note the orientation; reinstall existing seals/clips in their original positions if applicable
• Tighten fittings snugly without overtightening; restore water and check for leaks before use

This repair set renews the hinge pivot components so the door opens smoothly and closes squarely. Replacing the worn hardware helps maintain proper alignment and a tight gasket seal for consistent performance. What it does:

• Replaces worn hinge pin/bushing hardware to restore door support
• Helps fix a door that sags, scrapes, or won't close flush
• Can reduce clicking, squeaking, or grinding at the hinge
• Helps the door seal make full contact to prevent warm air leaks

• 1 repair set

• Disconnect power; if applicable, turn off the water supply
• Remove items from the door; support the door and lift it off the hinge
• Install the new hinge hardware in the original orientation
• Reinstall and align the door; verify gasket seal and adjust leveling if needed

Replacement silverware basket with integral handle in dark gray. Holds forks, knives and spoons in the lower dishwasher rack to keep utensils upright for better cleaning and easier loading, removal and transport. What it does:

• Holds and separates flatware to reduce nesting and promote water flow during wash cycles.
• Integrated handle makes it easy to lift the basket in and out of the rack for loading or unloading.
• Keeps small items from falling through the rack and reduces rattling during operation.
• Replace the basket if it is cracked, broken, or if utensils no longer stay securely in place.

• Installs in the lower dishwasher rack by sliding or snapping into existing rack slots; typically requires no tools.
• Make sure the basket sits level and the handle moves freely before running the dishwasher.
• Inspect for cracks or sharp edges and replace if damaged to avoid utensil loss or interference with spray action.
• Disconnect power first; this part itself does not require electrical work.

The Handle is an OEM part for Bosch dishwashers. It provides the surface for securely grasping and maneuvering the dishwasher door during opening and closing. 

Causes of a bad handle can include wear and tear from ongoing grasping motions. Repeated lifting and adjusting of the door places stress on handle components over time.

Symptoms of a bad handle include:

• Looseness, wobbling or detachment from the door assembly
• Sharp edges, cracks or splits compromising a firm grip
• Reduced ability to precisely guide the door into position

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Levelling Foot is an OEM replacement part designed specifically for Bosch dishwashers. It works to properly position and stabilize the appliance for balanced and smooth operation. Causes of a bad levelling leg/foot can include general wear and tear over time. 

Symptoms of a bad levelling foot include: 

• An unbalanced or unstable dishwasher during use
• Rocking or shifting of the unit on an uneven surface 

This genuine OEM Bosch part restores proper alignment and support of the dishwasher to ensure optimal performance and noise reduction. This Bosch part can also be used on Thermador and Gaggenau appliances.

This replacement foot is the leveling support at the base of your appliance. It helps set the height and keep the unit stable and level, reducing wobble, vibration, and noise for smoother, quieter operation.

• Supports the appliance base and provides solid floor contact
• Allows height/leveling adjustment as designed by the unit
• Helps correct rocking, vibration, walking, or door misalignment caused by an unlevel appliance
• Replace if the foot is cracked, missing, worn, or stripped and won't hold adjustment

• Disconnect power; shut off water supply if applicable
• Protect flooring and have a helper steady or move the unit
• Remove the damaged foot; install the new foot per the mounting style (threaded or push-in)
• Adjust height to level the cabinet and stability at all corners

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

The Fine Filter is an OEM part for Bosch dishwashers. It is designed to trap small food particles and debris before they can clog other areas of the dishwasher.

The fine filter is positioned inside the dishwasher tub and spray arms to act as a preliminary filter. It helps keep the wash and rinse zones free of obstructions to allow for the best cleaning performance.

Causes of a faulty fine filter are normal product usage over time, accumulation of stubborn food or mineral deposits, and occasional damage from sharp dish edges

Symptoms of a bad fine filter include:
Buildup of muck or grime that cannot be cleaned
Torn or damaged mesh that no longer traps particles
Improper drainage or water not circulating as it should
This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Door Seal is an OEM part for Bosch dishwashers. This part is responsible for creating a watertight seal around the dishwasher door, keeping water contained within the dishwasher and preventing it from leaking onto the floor.

A bad door seal can occur due to wear and tear, exposure to heat and chemicals, or accidental damage. Signs of a faulty door seal include visible cracks, tears, or a loose fit around the dishwasher door.

Symptoms of a bad door seal include:

• Water leaking from the dishwasher door  
• Wet or damp areas around the dishwasher 
• Inefficient cleaning or rinsing 

Replace your worn-out or damaged dishwasher door seal with this genuine OEM Bosch part to restore your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

The Dishwasher Hinge Lever is an OEM replacement part for Bosch dishwashers. This hinge lever is crucial for the operation of the dishwasher door, supporting smooth movement as it opens and closes. It works alongside the door springs to provide balanced tension, ensuring that the door stays securely in place when opened or closed. 

Over time, hinge levers may wear out due to regular use, strain from overloading the door, or corrosion from prolonged exposure to moisture. A damaged hinge lever can disrupt the door’s movement, leading to issues with opening, closing, or improper sealing of the dishwasher door.

Symptoms of a bad Dishwasher Hinge Lever include:

• Difficulty opening or closing the dishwasher door
• The door dropping open without resistance
• A loose or sagging door that won’t stay securely in place
• Unusual noises when moving the door 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Replacement door hinge that restores proper door alignment and smooth opening/closing for compatible Bosch appliances. Simple, direct support for the door pivot to reduce sagging, uneven closing, and noisy operation. What it does:

• Supports the appliance door pivot and maintains correct door alignment during use.
• Helps stop door sagging, uneven gaps, and doors that don't close or latch reliably.
• Restores smooth opening and closing and reduces hinge-related noise.
• Works as the mechanical pivot/connection between the door and cabinet frame.

• Turn off power and disconnect the appliance (and water supply if applicable) before starting any repair.
• Support the door while removing/installing the hinge to prevent damage or injury.
• Use the original mounting hardware or manufacturer-recommended fasteners; tighten securely but avoid overtightening.
• After installation, check door alignment and operation; adjust as needed per manufacturer instructions.

This genuine replacement seal provides a watertight connection where components join, helping prevent leaks and maintain normal appliance performance. Use when an old or damaged seal allows water to escape or pooling occurs. What it does:

• Creates a tight seal between mating parts to stop water leaks
• Restores proper sealing at appliance joints or hose connections
• Helps prevent water damage and reduces the chance of intermittent leaks
• Commonly replaced when a seal is cracked, flattened, or missing

• Turn off power and water supply before replacing the seal.
• Clean and dry mating surfaces thoroughly before installing the new seal.
• Ensure correct orientation and proper seating so the seal sits evenly in the groove.
• Inspect adjoining parts for wear; replace damaged components to ensure a proper seal.

The Adapter is an OEM part for Bosch dishwashers. It is used to connect the dishwasher water inlet hose to the internal water supply component. Proper sealing and connections are critical for leak-free dishwasher operation.

Causes of a bad hose adapter can include mineral buildup interfering with the seal, cracks developing from repeated heating and cooling cycles, or accidental damage during hose handling.

Symptoms of a bad hose adapter include:

• Water leaks at the hose connection point
• Mineral deposits or residue left around the area
• Reduced water pressure or flow to internal components
• Inability to establish a tight seal when connecting the hose

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This sealing is a molded rubber gasket that provides a watertight barrier where two appliance components meet, helping prevent leaks and water damage. It's a direct-fit replacement when the original seal is cracked or worn. What it does:

• Creates a watertight seal to help prevent leaks during operation
• Restores proper sealing where the original gasket has become brittle, torn, or flattened
• Helps maintain appliance performance by keeping water inside the wash/tub area
• Reduces risk of water damage to cabinetry or floors from failing seals

• One sealing

• Disconnect power and water supply before beginning any repair
• Verify mating surfaces are clean and dry; remove any old sealant or debris for a proper fit
• Inspect the replacement for damage before installing and align evenly to avoid pinching