Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Color: clear. Measures about 3 inches in diameter.
Troubleshot the oven by checking the broiler which worked good (same fuel valve). After reading the some tips about troubleshooting the Glow Ignitor I could see the broiler ignitor got white hot and the oven ignitor only got bright orange (orange to red causes intermittent ignition or mini explosions). Watched the how to video and it was good information. You should be observant about which openings in the back of the oven as to where the two wires are coming out of. My oven is over 12 years... Read more
If your range has a strong burning smell or won't power on, the terminal block may be heat-damaged. This insulated connector restores safe power flow.
Replaced it with the part I got from you. Read more
This contact spade is a push-on electrical terminal used to connect an appliance wire lead to a component's blade. Replacing a worn or heat-damaged connector restores a secure fit and consistent power flow.
Full disassembly of removable tray into top plate (stainless) and lower pan taking care not to loose fasteners. Removal of terminal blocks using lubrication on rusted screws and, if necessary, drill out technique. Unclip wires from edges of the tray on both sides without losing the clips for future re-use. Top plate is now completely free of connections and may be cleaned/scrubbed separately in advance of re-assembly. Unfasten spade insulation block (located in the front of the tray) after... Read more
Replace cracked, broken, or shattered inner door glass on your oven. Installs between door panels in the window frame assembly. Reuses existing frame.
Removed 3 screws on top of door, 3 screws on bottom if door which released glass front. Then removed 4 nuts on sheet metal window cover to get to window. To get to the broken glass there was one tab on the corner of the window frame that had to be bent upward to loosen the frame. Removed the broken glass, slid in the new glass, re tightened the frame and put everything back together. It took me a little longer than it should have because I forgot the reverse order for putting it back... Read more
This is a blower wheel used in the downdraft exhaust ventilation system of a range or cooktop. It mounts on the motor shaft and draws smoke, steam, and cooking odors down and out through the vent ductwork. Replace this part if the exhaust fan is noisy, vibrating excessively, or not moving air effectively despite the motor running.
I replaced the downdraft fan and fan motor of my 25 year old JennAire C301 cooktop. The issue was getting the fan/motor assembly out in such a tight place. I had to first remove the fan cover, cut the wires, then the assembly came out. Putting back wasn't as tough although getting the cover back on (over the motor) was a bit of a strain. Wired it back, turned it on, and was thrilled. Now I'll replace the knobs and burners and we're back in business. Read more
This part is a grill element that is used on a cooktop. The element is responsible for supplying heat to the cooking area of the cooktop. If the element is not lighting up orange or red when it is turned on, it will need to be replaced. This part may need to be replaced over time due to normal wear and tear on the appliance. Some users may also notice that the element is not heating evenly or works intermittently. If this is the case, this is a genuine OEM replacement part that is made out of high-quality materials. Unplug the range from the electrical outlet and allow the cooktop ample time to cool down before trying to replace it. Wear work gloves for safety during this process.This part is compatible with cooktops that are manufactured by Jenn-Air and Maytag. It is sold individually and comes from the manufacturer.
Ordered all the parts needed, replaced them and the Jenn Air worked just fine. Read more
Straight flat oven rack installs inside your oven to provide level support for cookware. Replace bent, discolored, or missing racks for smooth loading.
I forgot to remove the racks when I cleaned the oven. I've done it twice before and could reshine them but this time I opted for replacement and a downdraft filter while I was ordering. They look great. Read more
Factory fastener secures appliance panels, brackets, and internal components. Replace worn, stripped, or missing screws to restore tight fit and alignment.
Fixed my self Read more
This motor isolator is a vibration-damping grommet that cushions the motor mount to reduce noise and prevent metal-to-metal contact. Replacing worn isolators helps keep the motor seated correctly and the appliance running quieter and smoother.
Ordered three isolators and changed all of them. Sounds like new. Read more
Fixes ovens that won't heat or show F8/F9 error codes. This relay switches power to heating elements and fans. Moderate DIY repair with multimeter.
I first tested and replaced the temperature sensor. Since this is a slide-in range, I managed to pull it out just enough to access the back without disconnecting the downdraft and gas line. (For wall models this would not be the case.) Unfortunately, that did not do it. Next I replaced the lower heating element because it was a little below the ohms level it should be at. No go. So far, both of these were pretty easy to do and were relatively inexpensive so I wasn't too frustrated. Then I... Read more
Color: Black. Instruction sheet included.
Removed rocker switch,made up jumper so the compactor could be used while awaiting replacement switch. The part came 2 days later and was installed in less tha 5 minutes. Unit working like new again. Thanks for the great service!! Read more
Screw: 8-16 x 3/8 inch.
A shoulder screw that secures appliance components and provides a precise pivot or spacer point. Replaces a missing or worn screw to restore alignment, reduce rattling, and keep panels and assemblies securely in place. What it does:
I had to remove the oven door, which I learned is made to come off without tools. Then took out the bottom by removing two screws and lifting. Removed the screws attaching the igniter, pulled wires thru back until I could get the connector and disconnect. When the new igniter arrived, I had to change the connector. I cut the one off the old one, and spliced to the new one using solder and shrink tubing. Just reverse the procedure to install. I replaced the screws with new ones. Read more
If your oven overheats or shows temperature errors, this temperature probe restores accurate heat sensing. Simple DIY fix in 15 minutes or less.
Common sense and following directions from a tech, Read more
Hex head sheet metal screw secures appliance panels, brackets, and trim. Replace missing, stripped, or damaged screws to keep covers firmly attached.
Replacement fastening screw for securing trim, panels, and brackets inside appliances. Use when original screw is missing, stripped, or damaged.
I pulled out the old housing and unplugged the motor. It pretty much came out in pieces. Remove the plastic from the motor, then had to take a pair of vice grips to hold the spindle in place to remove the auger. Remove what was still attached to the old Housing. Cleaned everything up and put the whole unit back together. The motor looked like it was somewhat cooked but still worked, so I ordered a new motor and auger to replace it. Because this fridge is 24 yrs old, Appliancepartspros... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.