T36ib800sp/50 Parts

This foot installs at the appliance base to support and level the unit. Replacing a worn or missing foot restores stability, reduces vibration and rattling, and makes accurate leveling easier.

• Provides a stable contact point between the appliance and the floor
• Allows height adjustment during leveling
• A damaged or missing foot can cause wobbling, uneven operation, vibration, or noise
• Common signs include cracking, deformation, or a loose/stripped attachment

• Disconnect power and shut off any utilities before servicing
• Carefully tip or raise the appliance to access the base; use a helper and proper supports
• Install the new foot and adjust height to level the unit
• Verify stability front-to-back and side-to-side after re-leveling

This heating element is the dishwasher heater assembly that warms wash water and helps the dry cycle perform properly. Replacing a failed heater restores water temperature control and improves cleaning and drying results. What it does:

• Heats wash water so detergents and sanitizing cycles work effectively
• Supports the dryer/tub warming stage to reduce residual moisture on dishes
• Common symptoms: dishwasher doesn't heat, dishes remain cold or wet, or cycles take longer than normal
• Works as the OEM heater assembly designed for compatible Bosch dishwashers

• Disconnect power (and water, if applicable) before servicing to avoid shock or injury
• Access typically requires removing the lower access panel or dishwasher base; follow OEM service instructions
• Inspect mounting hardware and seals; replace any damaged clips or gaskets to prevent leaks

This replacement fixture is the factory mounting housing that secures its paired component inside your appliance. Replacing a damaged or missing fixture restores proper support and alignment for reliable, rattle-free operation.

• Provides the mounting structure to hold the associated part in the correct position
• Helps protect connections from strain and vibration
• Common signs it's needed: cracked or broken housing, loose fit, rattling, or the attached part won't stay in place/intermittently works
• Direct-fit replacement built to match the original form and connection points

• Disconnect power to the appliance before service; shut off gas or water if applicable
• Access location varies by model; refer to your service manual and document wire routing/fastener locations
• Transfer any screws, clips, seals, or wiring from the original if they are reused
• Do not overtighten fasteners into plastic; check for a secure, even fit before reassembly

The Water Inlet is an OEM component specifically designed for Bosch refrigerators featuring internal water filtration and dispensing systems. It serves as the entry point for unpurified water into the appliance.

The water inlet utilizes precise engineering to thread securely onto liquid supply lines. Its feed line transport capacity is rated to withstand regular high-pressure pulses from large filtered volumes. 

Causes for inlet replacement typically relate to normal wear at the threaded fitting connection over time. Loosening can affect water tightness and risk leak development.

Symptoms of a failing water inlet include:

• Water leakage around the inlet fitting 
• Loose inlet face or threads requiring tightening
• Diminished water flow rates into the refrigerator 

 This OEM Bosch replacement part is also compatible with Thermador, Gaggenau, and some Kenmore refrigerator models utilizing matching water system architectures. Reinstallation restores a tight seal and reliable supply transport functionality.
 

Replacement retaining pin that secures appliance components so panels, hinges or linkages stay connected. Use this direct-fit hardware to restore proper alignment and reduce looseness, rattling or separation caused by a missing, bent or worn pin.

• Secures mating parts like hinges, levers or shafts to prevent separation and play
• Common symptom: loose or rattling door/panel or misaligned assembly where the original pin is missing or damaged
• Typical use: keeps pivot points and small assemblies aligned for proper operation
• Metal fastener designed for a simple, local replacement

• Disconnect power (and water, if appliance type requires) before servicing
• Remove any obstructions and note original orientation before removing the old pin
• Use appropriate hand tools; do not force parts—if fit is tight, inspect mating components for damage

This gutter heating heating element helps prevent ice dams and keeps gutters and downspouts clear so melting water can drain away. It's a direct-replacement service part used in compatible Bosch systems to reduce ice buildup. What it does

• Provides localized heat to gutters and downspouts to help melt snow and ice
• Helps reduce ice dam formation that can cause overflow or water backup
• Restores proper drainage when frozen buildup is the cause of gutter blockage
• Commonly used when you see visible ice on gutters, water backing up, or slow roof drainage

• One gutter heating element assembly

• Intended for installation by an experienced DIYer familiar with appliance electrical work
• Disconnect power to the appliance and associated circuits before servicing
• Follow OEM wiring and mounting instructions; use appropriate outdoor-rated wiring and fasteners
• Inspect connections and weather seals after installation and test operation before finalizing

This small replacement clip secures a mating part in its proper position inside the appliance. Replacing a cracked or missing clip restores a snug fit, helps prevent vibration, and keeps components correctly aligned for dependable performance.

• Holds an attached component securely in its bracket or mounting point
• Helps eliminate looseness and rattling caused by a weakened or missing clip
• Maintains alignment to support proper operation and reduce wear
• Common symptoms: broken/missing clip, loose or wobbly part, rattling noises

• Disconnect power; turn off water or gas supply before servicing
• Note the original clip's orientation and take a reference photo before removal
• Avoid over-bending the new clip; replace any deformed mating parts
• Test operation before reassembling covers or panels

This is a mounting fixing kit used to secure specific dishwasher components. It replaces worn or missing hardware so parts stay firmly in place and the appliance operates as intended.

• Secures designated parts to prevent loosening, rattling, or misalignment
• Helps resolve issues like loose panels or components shifting during cycles
• Useful when original fasteners are stripped, corroded, or lost
• Restores proper fitment after service or replacement of related parts

• Disconnect power and turn off water before servicing
• Keep track of original hardware locations for correct reassembly
• Hand-start screws to avoid cross-threading; tighten to snug, do not overtighten
• Address corrosion or damage present on mating parts before installation

This condenser fan circulates air across the condenser coil to help remove heat from the refrigerator, improving cooling efficiency and preventing compressor overheating. It replaces a worn or damaged condenser blower assembly. What it does:

• Moves air over the condenser coil to dissipate heat from the refrigeration system
• Restores proper condenser airflow when the original fan is seized, noisy, or not spinning
• Helps prevent excessive compressor run time and warm cabinet temperatures caused by poor condenser cooling
• Rubber mounts reduce vibration and noise transfer to the cabinet

• One condenser fan assembly with rubber mounting grommets

• Disconnect power to the appliance before starting and follow all safety precautions
• Access often requires removing the rear lower service panel or toe-kick; keep track of fasteners
• Handle the fan blade and motor carefully to avoid bending blades or damaging the shaft
• After installation, verify unobstructed blade rotation and test the unit for normal operation

This door hinge secures and guides an appliance door, restoring stable, smooth opening and closing. Use it to replace a broken, bent, or worn hinge so the door hangs correctly and seals as intended. What it does:

• Provides a pivot point so the door opens and closes smoothly
• Restores proper door alignment and prevents sagging or dragging
• Helps the door form a proper seal to maintain temperature and function
• Fits the factory mounting locations for a direct replacement

• One door hinge

• Disconnect power and empty the door before starting; support the door while removing mounting screws
• Use appropriate hand tools and keep fasteners for reuse unless new hardware is provided
• Tighten screws securely but avoid over-torquing to prevent damage

This is a replacement dryer complete assembly designed to restore drying function and structure for compatible Bosch laundry units. It provides the main cabinet and drum enclosure needed for normal tumbling and airflow. What it does

• Houses the drum and internal components so clothes can tumble during the drying cycle
• Provides the enclosure and mounting points for the blower, heating system, and controls
• Restores proper airflow pathways to help the dryer heat and vent as intended
• Helps eliminate issues caused by damaged or severely warped cabinet or drum housings

• One complete dryer assembly as shown

• Disconnect power before servicing
• Follow factory service manual for alignment, seal, and vent reconnection steps
• Inspect and replace any worn seals, ducts, or mounting hardware as needed during installation

This factory repair set provides the factory-specified components needed to restore proper operation of compatible Bosch appliances. It replaces worn or damaged service parts so the appliance can perform as intended. What it does

• Replaces the original service components supplied in the repair set to restore normal function.
• Helps stop symptoms caused by worn parts, such as loose fittings, intermittent operation, or minor leaks when those parts are affected.
• Restores proper alignment or mounting where included components secure moving parts.
• Useful when troubleshooting issues traced to the specific assembly the kit services.

• Disconnect power and, if applicable, water supply before beginning any repair.
• Follow the manufacturer's service instructions and use only the supplied components.
• Inspect surrounding parts for wear; replace additional damaged components as needed.

This ice maker assembly replaces the refrigerator's frozen-water harvesting module so your freezer can produce and dispense ice reliably. Restores automatic ice production when the original unit fails. What it does:

• Collects and freezes water, then cycles to eject ice cubes into the storage bin
• Triggers the fill valve to allow water into the mold during the harvest cycle
• Helps stop intermittent or complete ice production when the ice maker is worn or failed
• Can resolve issues like no ice production, small or misshapen cubes, or frequent cycling

• Disconnect power and shut off the refrigerator water supply before starting
• Handle the unit and connectors gently to avoid damaging the fill valve and wiring
• Confirm freezer temperature is within the manufacturer's recommended range for ice production after installation

This insulating part is a factory replacement insulation panel that helps limit heat transfer and dampen noise inside the appliance cabinet for reliable operation and quieter cycles. Use it to restore proper thermal/sound control after damage or removal. What it does

• Replaces worn, torn, or missing insulation to reduce heat loss and help maintain internal temperatures.
• Dampens operational noise from motors and pumps for quieter appliance cycles.
• Protects surrounding components from direct heat exposure.
• Helps the appliance reach and hold proper operating conditions more efficiently.

• One insulating panel as shown.

• Inspect surrounding clips and fasteners; replace any that are damaged before installing the new panel.
• Position the panel carefully to avoid compressing or folding the insulation; secure per original mounting points.
• Disconnect power before accessing the appliance interior and follow all safety precautions.
• If adhesive was used on the original, use heat- and appliance-rated adhesive or fasteners as specified by the manufacturer.

This operating module is the user-interface control board assembly that manages cycle selection and user commands, helping your appliance respond correctly to button presses and display status information. It restores control functionality when the interface fails. What it does:

• Receives and processes user inputs from buttons or touch controls so the appliance can start and change cycles.
• Sends signals to the main control and other components to execute selected functions.
• Can resolve symptoms like unresponsive controls, missing or incorrect display information, or inability to select cycles.
• Works as the interface layer between the user and the appliance's main electronics.

• Disconnect power to the appliance before starting work to avoid shock or damage.
• Handle the module carefully and avoid touching exposed circuitry; use anti-static precautions where possible.
• Some disassembly of the control panel is typically required; keep fasteners and small parts organized.

This rail guides a dishwasher rack so it slides smoothly in and out, restoring proper rack alignment and reducing jams. It's a direct-fit replacement when an original rail is bent, worn, or broken. What it does

• Guides the rack on its rollers to keep it level and aligned during loading and unloading
• Prevents the rack from binding or derailing while extending or retracting
• Helps restore smooth rack movement if the original rail is bent, cracked, or worn
• Works with the rack rollers and end stops to maintain safe, consistent operation

• One replacement rail

• Basic tools are usually all that's required; verify rail orientation before removing the old part
• Remove the affected rack and rollers as needed to access and replace the rail
• Inspect rollers and end stops while servicing; replace any damaged components for best results
• Disconnect power to the appliance before performing any service that exposes wiring or electrical components