Taws700e Parts

Washer lid hinge attaches the lid to the cabinet, allowing smooth opening and closing. Replace if cracked, rusted, broken, or causing lid misalignment.

This clutch spring cap retains and protects the clutch spring in your washer's drive/clutch assembly, maintaining proper tension. Replacing a worn or missing cap helps the clutch engage smoothly and reduces slipping and noise during spin.

• Secures the clutch spring within the clutch assembly to prevent movement or dislodging
• Maintains correct spring preload for consistent clutch engagement
• Can help reduce clutch slip that appears as weak/no spin, slow spin ramp-up, or intermittent spinning
• Common signs of trouble: rattling or scraping near the drive, burning smell, or a visibly damaged/missing cap

• Unplug the appliance and shut off water before servicing
• Access the clutch per your model's service procedure; removing the gearcase/transmission and clutch may be required
• Carefully relieve spring tension and note the orientation of the spring and cap before removal
• Inspect the spring, clutch lining, and related hardware; replace any worn components during reassembly

Knurled pin secures knobs or dials to control shafts in washers. Replace if the original is missing, worn, or damaged to stop loose or spinning knobs.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Leaking washer during drain cycle? This drain hose clamp secures the connection to prevent water leaks and hose pull-off from vibration or pressure.

For mating terminal use WP94614.

For mating terminal use [AP31136300].

Size: 10-24 x 3/8 inch.

This pressure switch is a factory-replacement control that senses air/pressure changes and helps the dryer run correct cycles and safety functions. It restores proper pressure detection so the dryer can heat and cycle as intended. What it does:

• Detects air/vacuum pressure changes to signal the dryer control for cycle and safety operations
• Helps ensure normal heating and timed cycles by allowing the control to confirm airflow/vent conditions
• Common symptom linkage: dryer won't heat, won't start, runs too long, or displays pressure/airflow-related fault codes
• Works with the dryer's vent/air sensing system

• One pressure switch

• Disconnect power before servicing to avoid shock or injury
• Inspect hoses and venting for blockages; replace damaged vacuum/air hose when installing this switch
• Handle connectors and terminals gently; ensure secure electrical connections and correct routing of pressure hose

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area

Replacement shaft sleeve bushing for washers. Fits over rotating shafts to reduce friction and protect surfaces. Replace when worn, cracked, or missing.

Washer won't spin or vibrates excessively? This spring damper assembly cushions the drum during spin cycles, reducing vibration for smooth operation.

This syphon breaker prevents dirty drain water from being siphoned back into the dishwasher, helping maintain proper draining and protect wash water from contamination. It's a direct-replacement drain air-break for compatible dishwashers. What it does:

• Stops backflow/siphoning from the household drain into the dishwasher
• Helps maintain proper drain performance and prevents wastewater re-entry
• Can reduce odors and cloudy or soiled dishes caused by contaminated wash water
• Works as part of the dishwasher's drain plumbing to preserve wash hygiene

• Disconnect power to the appliance and turn off water supply before servicing
• Replace only with identical part and ensure correct hose routing and secure clamps
• Inspect adjacent drain hoses and connections; replace damaged hoses or clamps as needed

Secures shafts and pulleys in your washer to prevent axial movement. Replace when worn or damaged to restore proper alignment. Confirm fit with model.

Drain hose nozzle that attaches to the end of your washer's drain hose. Replace if cracked, broken, or missing to ensure proper hose connection.

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.