Tfx20jr Parts

Specs: 8-18 AB IHW 5/8 S

Ice storage bin holds and stores ice produced by the refrigerator's ice maker so cubes are ready for dispensing and stay contained. Replaces cracked, broken, or missing bins to restore normal ice storage and delivery. What it does:

• Collects and stores ice made by the ice maker so cubes are available for dispensing.
• Guides ice toward the dispenser/auger area and helps prevent ice from spilling into the freezer.
• Restores proper ice containment when the original bin is cracked, warped, or missing.
• Helps reduce ice clumping and jams caused by broken or misaligned storage containers.

• Disconnect power to the refrigerator before removing or installing the ice bin.
• Remove shelves or drawer(s) as needed for access; lift out the old bin carefully to avoid damaging the ice maker or dispenser components.
• Align tabs and guides on the new bin and slide into place without forcing; listen for the bin to seat properly.
• After installation, restore power and run the ice maker/dispenser through a test cycle; discard the first batch of ice after reinstallation.

This kit restores your refrigerator's automatic defrost, melting frost from the evaporator so airflow and temperatures stay consistent. Use it when frost builds up and cooling performance drops in the fresh food section. What it does:

• Heats the evaporator coil during the defrost cycle to melt frost and ice
• Bimetal thermostat opens to end defrost at the correct temperature, preventing overheating
• Helps maintain proper airflow between freezer and refrigerator compartments
• Common signs include heavy frost on the back freezer wall, warm refrigerator section, or long run times with poor cooling

• 1 defrost heater and 1 defrost termination thermostat

• Unplug the appliance before service; wear cut-resistant gloves—edges can be sharp
• Remove freezer shelves/bin and rear panel to access the evaporator; photograph wiring for reference
• Clip the new thermostat to the same tubing location/orientation as the original and ensure firm contact
• Route wiring like the original, avoid damaging fins, reinstall the rear cover for proper airflow, and allow up to 24 hours for temps to stabilize

Size: 10-16 ab.

According to GE you must also replace part number WR17X4341 auger when replacing this part.

This freezer door light switch turns the interior freezer light on and off when the door opens and closes, restoring proper illumination so you can see contents clearly and avoid wasting food. What it does:

• Activates the freezer interior light when the door opens; deactivates it when the door closes.
• Replaces a worn, stuck or intermittent switch that causes the light to stay on, not turn on, or flicker.
• Fits into the door or cabinet frame mounting and connects to the existing wiring harness for direct replacement.

• Disconnect power to the appliance before starting any repair to prevent shock.
• Typically snaps into place and connects to the factory wiring harness; no special parts required.

Includes 12 screws. Size: 8-18 ab.

Replacement bucket seal that fits around the refrigerator ice bucket to restore a snug fit and help keep ice contained while reducing frost, spills and water pooling. What it does

• Seals the ice bucket to the cabinet/shelf to help keep ice from spilling or shifting.
• Reduces frost build-up and melting around the ice bin area.
• Helps prevent minor water pooling from melting ice.
• Restores proper fit so the bucket sits flush and operates as intended.

• Disconnect power to the appliance before beginning any service.
• Remove the ice bucket and carefully peel out the old seal; clean the mounting surface of ice, debris and residue.
• Press the new seal into place, making sure it is fully seated and oriented correctly around the bucket.

This spacer is a small mounting support used to maintain proper clearance and alignment between refrigerator panels, doors, or components. It helps reduce rubbing, vibration, and noise by restoring correct spacing and fit. What it does:

• Keeps panels, trim, or components spaced correctly to prevent metal-on-metal contact and wear
• Helps align doors and panels for a flush fit and smoother operation
• Reduces vibration and rattling caused by misaligned parts
• Used wherever a fixed clearance or gap is required during reassembly

• Disconnect power to the appliance before beginning any service that requires panel or component removal
• Inspect mating surfaces for damage or debris before installing the spacer; replace any damaged fasteners
• Install in the same orientation and location as the original spacer; do not overtighten mounting hardware

Size: 8-32 t. Includes 12 screws.

Replacement screw that secures panels, trim and internal brackets to keep appliance components stable and rattle-free. Use when originals are missing, stripped, or broken to restore proper fit and safe operation. What it does:

• Secures panels, control housings, trim and small brackets so parts stay aligned and stable.
• Replaces missing or damaged fasteners that cause rattling, vibration, or loose assemblies.
• Keeps electrical and mechanical components properly positioned for reliable operation.
• Intended as a direct replacement where the OEM screw specified for the application is required.

• Disconnect power and unplug the appliance before starting any repair.
• Use the correct screwdriver or bit and seat the screw squarely to avoid stripping the head or threads.
• Do not overtighten—stop when snug to prevent damage to panels or plastic components.
• Keep removed screws organized; replace only with the identical OEM screw for proper fit.

This is a replacement 8-18 x 9/16 machine screw used to secure internal and external appliance components. It restores proper fastening and helps stop rattling or loose panels caused by worn or missing fasteners. What it does

• Secures panels, brackets, or small assemblies to prevent movement and vibration
• Replaces stripped, corroded, or missing screws that can cause rattling or misalignment
• Helps maintain electrical and mechanical connections by holding parts in proper position
• Appropriate where an 8-18 thread size and 9/16" length are required

• Replacement screw

• Disconnect power to the appliance before accessing internal components
• Use the correct driver to avoid stripping the screw head and ensure proper torque
• Do not overtighten; snug until secure to avoid damaging threads or parts

This boot auger motor drives the auger inside the ice dispenser boot to move ice from the bin to the dispenser chute. Replaces a failed motor to restore normal ice dispensing and reduce jams. What it does:

• Rotates the auger inside the dispenser boot to push ice forward for dispensing
• Helps prevent ice buildup by moving packed cubes during dispense cycles
• Stops working when motor windings or gears fail, causing no ice to dispense or intermittent dispensing
• Works with the dispenser drive and auger assembly to transfer ice from the bin to the chute

• One boot auger motor

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the freezer/refrigerator door trim and dispenser housing; follow OEM service instructions
• Inspect related components (auger, coupler, wiring) and replace if damaged

Package of 12

This dart clip is a small plastic retainer that secures wiring, tubing or trim inside your appliance to prevent rubbing and movement. It helps keep internal components in the correct position for reliable operation and reduced vibration. What it does:

• Secures wiring, harnesses or small tubing to chassis or panels to prevent abrasion
• Keeps trim and lightweight panels held in place to reduce rattling and noise
• Prevents loose components that can interfere with moving parts
• Common symptom of a failed clip: loose wires, rubbing noises or panels that don't stay aligned

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access may require removing panels or trim; keep fasteners organized for reassembly
• Replace only the damaged clips; push-fit design usually snaps into place by hand or with pliers
• If routing or securing wiring, ensure wires are not pinched and have proper clearance from moving or hot parts