Need Help?
Call
Replacement mounting screw for securing panels, trim, and internal components in appliances. Needed when original screws are stripped, lost, or damaged.
Replacement ice bin for side-by-side refrigerators. Holds and delivers cubed ice from the freezer dispenser. Replace if cracked, broken, or missing.
6 - 10 pl flp 1/2 s
Replaced water line & both damaged dispenser parts. Read more
Replacement mounting screw for refrigerator panels, brackets, and hardware. Secures loose components and reduces rattling from missing or stripped screws.
Replace thimble on bottom ,stop door bk,cam closure, ff bk slove the problem thanks for your input everything went well. Read more
Bottom freezer drawer handle end cap for refrigerators. Replaces cracked, broken, or missing caps that cover the handle ends. Restores appearance.
Replacement pivot that supports and aligns refrigerator doors or drawers. Needed when original pivot is cracked, broken, or worn, causing misalignment.
When we inspected the first time we found that Plactic had broken from the spiral part that for wards the ice. Also there were cracks in two places of other parts. There was a hole in the bottom of the bin. The new spiral was assembled and two new parts were replaced with help from the video and the diagram and the unit worked well. Two months later, ice maker would not forward any ice though the bin was full. We emptied the bin sand have ordered a new part or two in hopes that they will... Read more
Closes and protects the end of your refrigerator's mullion air duct on the door jamb. Replace this cap if cracked, broken, or missing to maintain a finished appearance.
Panel mounting screw for refrigerators. Secures access panels, trim pieces, and internal brackets. Replace lost, stripped, or corroded fasteners.
Installed new stainless steel pan replacing broken original plastic pan and installed new rubber grommets for the compressor Read more
Mullion air duct that directs airflow between refrigerator compartments. Replace if cracked, broken, or missing to restore proper air circulation.
Fix frost buildup on evaporator coils or a freezer that keeps icing up. This defrost heater assembly melts accumulated ice to restore proper cooling.
After reviewing a number of testimonials and your videos from your APP.com site I determined my most likely problem was either the defrost heater, thermostat, timer or possibly all three. The real challenge now began. Getting to the specific parts with my specific model number was a real challenge. It was not as easy as removing the light guard and 5 screws since my model had two Track Cant Shelf vertical rails restricting the removal of the back panel. Also, these rails could not be removed... Read more
Usually ships within 4 - 14 days
Internal water storage reservoir for refrigerator dispensers. Installs inside the fresh food compartment. Replace if cracked, leaking, or split.
This part was easy to install by following the directions from other users here. As long as you get the right hoses connected in the right places, everything else was straight forward. Takes a few minutes for the tank to initially fill and pressurize and clear the air in the line and then you're on your way to clean fresh water! Read more
Secures water and drain tubing to prevent leaks, noise, and vibration. Replace if loose, cracked, or missing. Confirm fit with your model number.
Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,... Read more
This solenoid saddle is a small mounting bracket that secures a refrigerator solenoid in the correct position. By preventing movement and misalignment, it helps the linked mechanism engage smoothly and consistently.
Easy fix once I found the problem. Broken solenoid sleeve. Part cost $2.58 + shipping. 10 minute repair. Read more
Ice crusher not working or slow crushed ice production? This helix front feeds ice to crushing blades. Moderate DIY repair—replace with auger for best results.
This was a very easy repair, the on-line video at AppliancePartsPros.com was helpful. The Helix was spinning freely (meaning, the Auger Blade was not holding it in place on the Auger). Pulling the assembly apart was a snap, and very logical (the video is perfect if you get lost). The family is now enjoying both crushed and cubed ice - and the redesign of the Auger Blade seems to prevent clogging in the ice shoot. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.