Wd330aeb/Xaa Parts

Base bracket that holds the leveling foot at the washer cabinet. Replace if cracked, broken, or missing to restore stability and prevent rocking or vibration.

This drain hose cap seals and secures the refrigerator defrost drain outlet so meltwater is directed into the drain hose instead of pooling in the cabinet. Replaces a worn or damaged cap to help stop interior leaks and water buildup. What it does:

• Seals the defrost drain outlet to prevent water from spilling into drawers or onto shelves.
• Guides defrost/meltwater into the drain hose and toward the drain pan.
• Helps reduce odors and pests entering through an open drain opening.
• Fits onto the drain outlet to replace cracked, missing, or loose caps.

• Disconnect power before working inside the refrigerator to avoid electrical hazard.
• Remove shelves and drawers as needed to access the drain outlet; clear any visible debris or ice first.
• Press the cap firmly onto the drain outlet/hose until fully seated; avoid excessive force or prying tools.
• After installation, pour a small amount of warm water down the drain to confirm proper flow and seating.

Mounts to the washer's lower frame to secure components and maintain alignment. Replace if bracket is cracked, broken, rusted, or missing hardware.

This small structural bracket supports the "leg" of an interior shelf or drawer assembly in compatible refrigerators. It helps keep shelves level and stable so bins slide smoothly and contents stay secure during everyday use. What it does:

• Supports the corner/leg of an interior shelf, cover, or drawer rail
• Helps maintain level alignment and prevents wobble or sagging
• Restores stability if the original piece is cracked, warped, or missing
• Common symptoms: shelf or drawer sags, binds, or rattles; poor fit/alignment

• 1 supporter leg

• Disconnect power and remove food from the affected area before starting
• Remove the shelf/drawer and note fastener locations or locking tabs
• Transfer any reusable screws/clips and seat the new supporter fully
• Reinstall components, ensuring the shelf/drawer sits level and moves freely

This is a flexible rubber bellows that connects the dryer exhaust outlet to the external vent duct on a combination washer/dryer unit. It channels hot, moist air out of the dryer section and helps absorb vibration during operation. Replace this bellows if it is cracked, torn, or collapsed, which can cause poor drying performance, excessive lint buildup, or moisture leaking inside the unit.

Secures the leveling foot to the washer base. Replace if cracked, stripped, or missing to restore a solid mounting point for proper leveling and stability.

Secures rubber hoses to fittings with constant spring tension to prevent leaks. Replace when rusted or weakened to maintain a tight seal. Confirm fit.

Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.

This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:

• Fits over standard appliance leveling legs to raise or lower each corner
• Helps stabilize machines to prevent rocking and uneven operation
• Reduces vibration and noise caused by unlevel appliances
• Useful when installing, moving, or re-leveling washers and dryers

• Turn legs slowly and adjust one corner at a time until the appliance sits level.
• Unplug the appliance (and shut off gas supply for gas dryers) before performing major moves or checks.
• Use caution to avoid pinching fingers when lowering legs; keep hands clear of pinch points.
• Check for damaged feet or mounting hardware and replace as needed.

Does not come with a hose or filter. These have to be purchased separately

Pivot hanger assembly that supports and stabilizes washer components. Replace if worn, damaged, or causing misalignment to restore smooth movement.

This is a door lock and switch assembly that secures the washer door during operation and signals the control board that the door is properly closed. It prevents the door from being opened while the drum is spinning and allows the wash cycle to begin. Replace this assembly if the washer won't start, displays a door lock error code, the door won't lock or unlock, or the cycle stops unexpectedly.

This shaped handle cap covers the end of a dishwasher door handle to restore a finished look and protect the handle connection. It keeps the door appearance consistent and hides the fastener area for a clean, finished fit. What it does:

• Replaces a damaged, cracked or missing handle end cap to restore appearance
• Covers and protects the handle mounting point from dirt and wear
• Prevents sharp edges or exposed fasteners on the door handle
• Matches the original profile so the handle closes and looks correct

• High-level replacement; may require removal of the door trim or handle screws—refer to your model's service instructions
• Disconnect power and water to the appliance before starting work to avoid injury
• Handle with care to avoid scratching painted surfaces; use appropriate trim tools if needed
• If fasteners are damaged, inspect and replace them with OEM-recommended hardware

This metal hook mechanism secures the washing machine door in the closed position during wash cycles for safe operation. It engages with the door strike to create a tight seal and prevent the door from opening while water is present. Replace if the door won't latch securely, pops open during cycles, or won't unlock after washing.

Replace a damaged, frayed, or worn power cord assembly. This part restores the electrical connection between your appliance and wall outlet.