Wdf530paybo Parts

This cover screw secures appliance panels and covers, keeping components protected and aligned. Replace missing, stripped, or corroded screws to restore a tight fit and help eliminate rattles, gaps, or panels that won't stay in place.

• Attaches an access cover or panel to the appliance frame
• Helps maintain proper alignment to protect internal components
• Replaces missing, stripped, or rusted hardware
• Typical signs: loose or rattling panel, cover won't stay secure, damaged or rounded screw head

• Disconnect power before servicing
• Support the panel while removing and installing screws to prevent misalignment
• Start threads by hand to avoid cross-threading; do not overtighten
• Use a matching driver bit to avoid damaging the screw head

The Detergent Dispenser Bracket is an OEM replacement part for Whirlpool dishwashers. Located inside the dishwasher tub along the edge, this bracket securely holds the entire detergent dispenser assembly in place. 

Causes of a bad bracket may be normal wear and tear over time, damage from overloading dishes, or accidental impact affecting the integrity of the plastic.

Symptoms of a bad detergent dispenser bracket include:

• Loose or unstable detergent dispenser  
• Detergent not dispensing or leaking
• Clanking noises coming from inside the tub
• Visible cracks, breaks, or deformations in the bracket 

This OEM Whirlpool part is also compatible with KitchenAid, Jenn-Air, Amana, and some Kenmore and Maytag models.

The Hinge Brace is an OEM replacement part for Whirlpool dishwashers. It serves as a supportive bracket anchoring the dishwasher door hinge assembly firmly in place.Note: This part may be different from your original. If your original part was a flat plastic vapor barrier, the new design is a wire. It is a factory design change, the old design is no longer available.

Over time, the hinge brace can degrade due to constant use, heavy loads on the door, or accidental impacts. A faulty hinge brace can result in misalignment or difficulty in operating the dishwasher door.

Symptoms of a bad hinge brace include:

• Loose or unstable door that does not close securely
• Gaps appearing around the door seal during wash cycles
• Broken hinge components from added stress and tension on the door
• Difficulty fully opening or closing the dishwasher door

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The Middle Spray Arm is an OEM replacement part for Whirlpool dishwashers. It is an integral component responsible for thoroughly washing dishes in the middle rack. Through its specially designed spray nozzles, the middle spray arm provides precise coverage for optimal cleaning.  Color: light gray. It measures approximately 19 inches wide.

Causes of a bad middle spray arm can include clogging or mineral buildup that blocks the spray nozzles over time. Damage, such as bent or broken arms, is another potential cause.

Symptoms of a bad middle spray arm include: 

• Dirty dishes remaining in the middle rack even after a cycle  
• Noticeable decrease in water pressure to the middle rack
• Spray from nozzles only partly hitting intended dish surfaces
• Arm mobility issues that prevent rotation during the cycle

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers.

The Wheel is an OEM part for Whirlpool dishwashers. This wheel attaches to the dishwasher rack, facilitating smooth and easy movement of the rack in and out of the dishwasher.  

Causes of damage to the Wheel can range from normal wear and tear, which eventually wears down the plastic, to overloading the rack with dishes, which can cause excessive stress and breakage.  

Symptoms of a failing Wheel include:

• The dishwasher rack jams or becomes difficult to move.
• A wheel falls off or appears visibly broken or damaged.
• The rack tilts or becomes unstable due to a missing or damaged wheel.
• Noises such as scraping or thumping when the rack is moved.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement dishrack restores secure loading and proper spacing so wash water reaches every item. Replacing a bent or rusty rack helps prevent tipped dishes and marks from flaking rust, and keeps loading/unloading smooth when the rack rollers are intact.

• Holds plates, bowls, and cups in place during wash and rinse cycles
• Maintains spacing for spray coverage and drying airflow
• Rolls in and out along the rails when paired with functional rack rollers
• Common symptoms include broken or bent tines, flaking coating or rust, items tipping, or difficulty sliding the rack

• Disconnect power to the dishwasher before servicing
• Open the door, pull the rack forward, release rack stops/end caps if present, and slide the old rack off the rails
• Transfer any reusable accessories from the old rack to the new rack as required by your model
• Slide the new rack onto the rails, reinstall rack stops, and verify smooth travel before running a cycle

The Hex-Head Screw is an OEM replacement part for use in Whirlpool dishwashers. This metal screw measures approximately ¾ inch long. Its primary purpose is to secure the dispenser bracket in place, ensuring stable operation. This hex-head screw is designed for use with compatible hexagonal tools. This makes installation and removal straightforward. This part is sold individually and is guaranteed to fit your dishwasher door panel. This screw is compatible with select Whirlpool brand models including Amana, Crosley, Estate, Inglis, Jenn Air, Kenmore, Kitchen Aid, and Maytag.

The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.

Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.

Symptoms of a bad power cord include:

• The dishwasher not turning on or completing cycles
• Warm or hot power cords during operation
• Frayed, cracked, or exposed copper wiring

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This overfill control float sits in the dishwasher tub and rises with the water level to signal the float switch to stop filling. Replacing a cracked or sticking float helps prevent leaks and recurring fill issues. What it does:

• Rises with the water level to actuate the float switch and stop the inlet valve
• Helps prevent overfilling and water leaking from the door
• A float stuck in the UP position can cause no fill or short fill
• A float stuck DOWN or damaged can allow overfilling

• 1 overfill control float

• Disconnect power and turn off water before servicing
• Remove the lower rack; lift out the old float from its guide and clear any debris in the well
• Insert the new float, ensuring it moves freely and reliably actuates the switch when raised

This wheel mount assembly fits the dishwasher's upper rack track and provides the roller that lets the rack glide in and out. Replacing a worn or broken mount restores smooth movement and keeps the rack aligned on the rails. What it does:

• Supports and guides the upper rack along the side rails
• Replaces cracked, missing, or seized rollers that make the rack hard to slide
• Helps prevent the rack from popping off the track or sitting unevenly
• Can reduce scraping or squeaking noises when moving the rack

• One upper rack wheel mount assembly

• Disconnect power to the dishwasher before servicing
• Open the door and remove the upper rack by releasing the rail stops
• Depress the locking tab to remove the old wheel mount from the rail; align and snap the new assembly into place
• Reinstall the rack and rail stops; check for smooth rack travel

This power cord connects your appliance to a household outlet. Replacing a worn or damaged cord restores safe, reliable power and can help resolve no-power or intermittent power issues caused by a compromised lead.

• Delivers electrical power from the outlet to the appliance
• Replaces cords with cracked, frayed, or heat-damaged insulation or a damaged plug
• Helps when the unit won't power on or loses power when the cord is moved
• Addresses visible scorching, arcing, or melting on the cord or plug

• Disconnect power before servicing; verify no voltage is present
• Note wire positions or take a photo before removal; match to the same terminals on install
• Use the proper strain relief/clamp and route away from sharp edges, moving parts, and heat sources
• Confirm the ground connection is secure; do not modify the plug

Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This pocket-style door handle provides the recessed grip used to open and close the appliance door. Replacing a cracked or missing handle restores a clean look and a secure, comfortable grasp for everyday use. What it does:

• Provides a built-in finger pocket for reliably opening and closing the door
• Replaces a broken, cracked, loose, or missing handle
• Helps resolve difficulty gripping the door or sharp/rough edges from damage
• Maintains proper look and prevents stress on adjacent trim or panels

• 1 pocket-style door handle

• Disconnect power to the appliance before servicing.
• Open the door and remove the screws/clips retaining the old handle; note orientation and placement.
• Reuse the existing fasteners/brackets as required and align the new handle carefully.
• Tighten fasteners snugly without overtightening; verify smooth door operation.

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

This heater terminal nut fastens the heating element's electrical connector to its stud, keeping the connection tight under heat and vibration. Replacing a worn or missing nut restores safe contact and consistent heating performance.

• Secures the wire/ring terminal to the heater stud for a solid electrical connection
• Helps prevent arcing, discoloration, and heat damage from a loose connection
• Signs include a loose terminal, burnt odor, or melted/charred insulation at the heater connection

• Disconnect power and allow the appliance and element to cool completely before service
• Photograph wiring for reference; remove old hardware and clean the terminal
• Inspect the ring terminal, insulators, and stud; replace any heat-damaged components
• Start threads by hand to avoid cross-threading; snug with the correct nut driver—do not overtighten