Wdt720padm Parts

This replacement screw secures appliance components, panels, and brackets. It restores a tight, reliable hold when an original fastener is missing or damaged, helping eliminate rattles, gaps, or shifting parts.

• Fastens two or more parts together inside the appliance
• Helps keep panels, brackets, or trim securely in place
• Can reduce vibration, rattling, or loose handles caused by missing/loose screws
• Replaces worn, stripped, or corroded fasteners

• Disconnect power and shut off water supply before servicing
• Match location and orientation to the original fastener
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to prevent stripping or cracking

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

This manifold channels wash water to the dishwasher's spray system for full coverage. Replacing a cracked or warped manifold restores proper water flow and wash performance while helping prevent leaks at the feed connection.

• Directs recirculated water from the pump to the spray arms/feed tube
• Maintains a sealed path to keep spray pressure consistent
• Damage can cause poor cleaning, weak spray, unusual noise, or internal leaks
• Cracks or broken tabs can leave spray arms misaligned or not spinning

• Disconnect power and turn off the water supply before servicing
• Open the tub; remove the lower rack and spray arm as needed for access
• Transfer any seals/O-rings or clips from the old part; seat all connections fully
• Run a short test cycle and check for leaks before reassembling

12 Ft in length

This main electronic control board governs the appliance's user interface and cycle functions, restoring responsive controls and correct operation when the original board fails. Replace a faulty control board to correct erratic or unresponsive behavior. What it does:

• Receives input from the console and sends control signals to relays, valves, motors and sensors.
• Restores normal cycle selection and timing when a failed board prevents the appliance from starting or completing cycles.
• Addresses symptoms like unresponsive or non-working buttons, blank or erratic displays, and unexpected program changes.
• Interfaces with safety and feedback sensors to coordinate appliance functions.

• Always disconnect power to the appliance before replacing the control board to avoid shock or damage.
• Handle the board by its edges and avoid touching circuit traces or components; the board is static-sensitive.
• Note connector locations or photograph wiring before removal to ensure correct reassembly.

This replacement mounting screw secures appliance components and panels. When original hardware loosens, strips, or goes missing, installing a new screw restores a snug, rattle-free fit and keeps assemblies properly aligned for reliable operation.

• Fastens brackets, covers, or internal components to the appliance frame
• Helps maintain alignment of panels, trims, and assemblies
• Replaces stripped or corroded hardware to reduce vibration, noise, or gaps
• Common signs it's needed: missing/loose screw, stripped head/threads, panel movement or rattling

• Disconnect power and shut off gas/water supplies before servicing
• Use the correct driver bit; start threads by hand to avoid cross-threading
• Repair/replace damaged clips or inserts before tightening
• Tighten snugly; avoid overtightening into plastic or thin sheet metal

Includes two screws, two clamps, and undercounter mounting brackets.

Color: White

This insulation pad installs in the factory location to isolate and cushion components or panels. It helps reduce vibration and limit unwanted heat transfer, supporting quieter operation and proper performance where the original pad was installed.

• Provides a thermal and acoustic barrier between parts or panels
• Helps minimize vibration and rattling noises
• Restores proper spacing/cushioning when the original pad is missing or deteriorated
• Replace if the pad is brittle, compressed, contaminated, or falling off
• Common signs include increased noise or rattles and localized hot spots or condensation

• Disconnect power (and gas/water, if applicable) before servicing
• Allow hot or cold surfaces to return to a safe temperature
• Note the original pad's location/orientation; remove old pad and clean the surface
• Install the new pad in the same spot without over-compressing; secure per the original method and verify clearances

Color: Grey

This overfill protector housing mounts in the dishwasher tub floor to guide the overfill float and position the switch actuator. Replacing a damaged housing helps stop leaks at the float opening and restores proper overfill protection.

• Guides the overfill float at the tub floor so it moves freely
• Allows the float to engage the overfill switch and stop water fill at high level
• Restores proper fit if the original housing is cracked, warped, or missing
• Typical symptoms include leaking near the float, overfilling, or inconsistent fill levels

• Disconnect power and shut off water supply before servicing
• Remove the toe panel and lower rack to access the float area
• You may need to lift out the float and remove the under-tub switch bracket to replace the housing; note part orientation
• After reassembly, run a brief fill and check for leaks at the float opening

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This replacement screw secures appliance panels and components so they stay tight and aligned. Replace a missing, rusty, or stripped fastener to restore a solid hold and reduce vibration or rattling during operation. What it does:

• Fastens and secures panels, brackets, trim, or internal components as specified for your model
• Replaces missing, corroded, or stripped hardware to restore a proper fit
• Helps prevent vibration, rattling, and misalignment caused by loose fasteners
• Addresses issues like a loose panel/handle or a screw head that's rounded off

• 1 screw

• Disconnect power; if applicable, shut off gas and water before servicing
• Use the correct driver size; start by hand to avoid cross-threading
• Tighten snugly—do not overtighten into plastic or thin sheet metal
• Keep track of original screw locations and lengths during reassembly

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken

The Insulation is an OEM replacement part for Whirlpool dishwashers. It is responsible for reducing noise and heat transfer during the dishwasher's operation. This insulation effectively dampens the sound generated by the dishwasher's motor, pump, and water spraying actions. It also helps to retain heat within the dishwasher, enhancing the drying performance and reducing energy consumption.

A bad insulation can occur due to wear and tear, water damage, or deterioration over time. If you notice symptoms such as increased noise levels during the dishwasher's operation, excessive heat escaping from the dishwasher, or reduced drying efficiency, it may be time to replace the insulation.

Symptoms of a bad insulation include:

• Increased noise levels during the dishwasher's operation
• Excessive heat escaping from the dishwasher
• Reduced drying efficiency

Repair your dishwasher by replacing the faulty or damaged insulation with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.