Weg555sobs01 Parts

This replacement bumper cushions and protects the appliance door or panel, helping stop metal-on-metal contact, reduce noise, and prevent chipping or wear. Simple, low-profile part that restores smooth, quiet door operation. What it does:

• Cushions door or panel to prevent hard impacts and protect finishes
• Reduces rattling and vibration-related noise during operation
• Helps the door close more softly and sit flush with the cabinet
• Prevents premature wear where edges contact the cabinet

• Disconnect power to the appliance before starting any repair.
• Inspect the damaged bumper and surrounding area, then remove the old bumper by hand or with a non-marring tool.
• Press the new bumper into the original mounting location until fully seated; no special tools normally required.
• If the bumper mounts to a clip or bracket that's damaged, replace the bracket.

This oven door gasket seals the oven cavity to keep heat and moisture in for even cooking and energy efficiency. A worn or damaged gasket can cause heat loss, longer cook times, or visible smoke/odor. What it does:

• Creates a tight seal between the oven door and cavity to retain heat and moisture
• Helps maintain consistent bake and roast temperatures for even cooking
• Reduces heat escaping that can trigger longer cook cycles or cycling issues
• Limits smoke and food odors from leaking into the kitchen

• Disconnect power and allow the oven to cool completely before servicing
• Remove the door per the manufacturer instructions if needed to access the gasket channel
• Inspect the gasket channel for debris and clean before installing the new gasket for a proper seal
• The gasket is fully seated along the door perimeter and check for pinched or twisted sections

This replacement screw restores secure fastening for appliance panels and components, helping stop loose parts and rattling so controls and panels stay aligned. Use when original screws are missing, stripped, or damaged. What it does:

• Secures panels, trim, control boards, brackets, or components to the appliance frame
• Stops rattling, vibration noise, and loose or misaligned parts caused by missing or damaged fasteners
• Replaces stripped, corroded, or missing screws to restore proper fit and function
• Matches OEM fit and threading for straightforward hardware replacement when the correct screw is identified

• Turn off power and unplug the appliance before accessing internal components
• Use the correct screwdriver or bit to avoid stripping the head; do not force mismatched drivers
• Tighten until snug—do not overtighten, which can strip threads or crack plastic
• Keep removed hardware organized and verify the replacement screw matches the original before installation

This surface ignitor lights the burner on compatible gas cooktops and ranges, restoring reliable spark ignition for normal burner operation. Replace a broken or weak ignitor to help restore consistent ignition and safer cooking. What it does:

• Generates the spark that lights the burner when the control is turned on
• Helps ensure quick, consistent ignition and reduces repeated clicking or delayed lighting
• Commonly replaces cracked, burned, or non-sparking ignitors
• Works with the cooktop's existing valve and electronic control to initiate flame

• Always disconnect power and shut off the gas supply before removing or installing the ignitor
• Handle the ceramic and electrode tip carefully—these components are fragile and can crack if dropped
• Reuse existing mounting hardware unless replacement is specified

This mounting bracket secures appliance components to the cabinet or chassis, restoring proper alignment and reducing movement. It's a direct-fit structural support used where panels or assemblies need a stable attachment point. What it does:

• Secures panels, trim or internal assemblies to the appliance cabinet to prevent shifting or sagging
• Restores proper alignment to reduce vibration, rattling or scraping noises
• Helps maintain door and panel fit for correct operation and appearance
• Used when a broken, bent or missing bracket causes loose or misaligned parts

• Disconnect power and water before starting any repair
• Verify bracket orientation and location against the appliance before tightening
• Use original mounting hardware when possible; inspect screws or clips and replace if worn

This replacement door glass is the clear window panel in the appliance's door. It restores a clear view and the door's protective barrier when the original glass is cracked, shattered, or hazed.

• Forms the transparent viewing window within the door assembly
• Supports proper door integrity and sealing when installed with existing trim/gaskets
• Replaces cracked, shattered, or scratched glass to remove sharp edges and restore appearance
• Common symptoms: spiderweb cracks, complete shatter, clouding/fogging, or a loose/rattling panel

• Disconnect power before servicing; allow it to cool completely
• Wear cut-resistant gloves and eye protection; handle glass carefully on a padded work surface
• Remove the door and separate panels; note screw locations and orientation
• Transfer any brackets, trim, or seals from the old glass and tighten fasteners evenly without over-torquing

Replace a damaged or missing gas burner knob to restore smooth, precise flame control and a clean, finished look. This knob attaches to the surface burner valve stem so you can turn the burner on and adjust heat levels.

• Attaches to the surface burner valve stem to select Off/ignite/heat settings
• Restores positive feel and control when the original knob is cracked, stripped, or loose
• Helps ensure accurate flame adjustment during cooking
• Common symptoms: knob broken, missing, wobbly, or spins without turning the valve

• Disconnect power and shut off gas before servicing
• Pull the old knob straight off the valve stem
• Align the new knob with the valve stem and press straight on until fully seated
• Verify smooth rotation and proper Off position after installation

The Door handle assembly is an OEM part for Whirlpool ranges. It is a component that includes both the door handle for convenient access, as well as the vent responsible for safely removing heat, smoke, and odors from the oven cavity.

Causes of a bad door handle and vent assembly can include wear from continuous use, heat exposure warping plastic components, or damage from impacts over time. Grease and food debris buildup can also deteriorate vent fan motors and air channels.

Symptoms of a bad assembly include:

• Difficulty opening or closing the oven door
• Excessive smoke or burned food smells
• The vent fan not operating or exhausting properly
• Internal components like springs or bearings becoming loose

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The Range Oven Door Glass is an OEM replacement part for Whirlpool ranges. This panel serves as a protective layer for the inner components of the oven door. It helps insulate the oven cavity, keeping the heat inside during cooking while preventing the external surface of the door from becoming too hot to touch.

Causes of a bad oven door include:

• Accidental impacts or mishandling
• Cracked or shattered glass
• Fogging or condensation between the glass layers

A damaged or worn-out outer panel can occur due to accidental impacts, scratches, or regular wear and tear. If you notice dents, scratches, or discoloration on the door panel, it may be time to replace it.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This orifice controls the flow of gas to a burner, helping produce the correct flame for safe, consistent cooking and baking. It replaces a worn or damaged gas metering jet to restore proper burner performance. What it does:

• Meter gas flow to a specific burner for correct flame size and heat output
• Helps maintain steady ignition and even cooking when functioning properly
• Commonly used when a burner shows a weak, uneven, or no flame
• Also replaces corroded or clogged jets that restrict gas flow

• Turn off the gas supply and power to the appliance before beginning work
• Use appropriate tools and avoid overtightening; match the replacement to the original part number
• Inspect for debris or corrosion and clean mating surfaces before installation

This door hinge secures and guides the active refrigerator door so it opens and closes smoothly while maintaining proper alignment. Durable replacement hinge restores correct door movement and helps prevent sagging or misalignment. What it does:

• Provides the pivot point and structural support for the active refrigerator door
• Keeps the door aligned for a proper seal and even gaps
• Commonly replaces hinges that cause door sagging, rubbing, or difficulty closing
• Works with the door assembly hardware to maintain smooth operation

• Disconnect power to the appliance and remove food/items from the door before starting.
• Support the door while removing and installing the hinge to prevent injury or damage.
• Reuse original mounting screws; tighten securely but avoid overtightening.
• After installation, check door alignment and adjust as needed for a proper seal.

This replacement grate kit restores a stable, level surface for gas cooktop cookware and improves burner access and heat distribution. Designed to replace worn, cracked or misshapen grates so pots and pans sit securely. What it does:

• Replaces damaged or warped cooktop grates so cookware rests evenly
• Restores proper spacing and support for burners and cookware
• Helps maintain consistent flame exposure at each burner
• Reduces rocking, slipping, and uneven heating caused by damaged grates

• For safety, shut off the gas supply and allow the cooktop to cool completely before beginning.
• Lift out old grates and set the new grates into position — no tools typically required.
• Inspect burner caps and heads for proper placement before testing burners.

A surface ignitor that produces the spark needed to light gas burners on compatible ranges and cooktops. Replaces a worn or failed ignitor to restore reliable ignition and consistent burner lighting. What it does

• Creates the spark at the burner to ignite gas when the control is turned on.
• Commonly used when burners click but fail to light or when a specific burner never ignites.
• Works with the cooktop's ignition system to provide consistent, repeatable sparking.
• Fits into the burner assembly and connects to the appliance's existing wiring and mounting.

• One surface ignitor (quantity: 1)

• Disconnect power to the appliance and shut off the gas supply before starting any service.
• Handle the ignitor by the ceramic/insulated areas; avoid touching the tip with bare hands to prevent contamination or damage.
• Confirm correct fit and secure all wiring connections; test ignition on a safe flame setting after reinstalling.

This end cap panel is a replacement trim piece that restores the finished edge and protects the appliance cabinet where panels meet. It helps maintain a clean look and keeps edges covered after repair or panel replacement. What it does

• Covers and protects the outer edge of a cabinet or control panel section to prevent exposed edges and wear
• Restores a flush, finished appearance after removing or replacing surrounding panels
• Helps keep dirt and moisture from reaching internal edges and seams
• Matches OEM fit and attachment points for reliable alignment

• One end cap panel

• Designed to snap or screw into existing mounting points — handle gently to avoid cracking plastic
• Turn off and unplug the appliance before removing nearby panels
• Inspect adjacent clips or fasteners and replace if damaged to ensure secure fit
• No special tools typically required; a screwdriver and trim tool may be helpful

Color: Black