Wfw79hebw0 Parts

Push-in nut that secures panels, trim, or small components to studs or shafts. Restores a firm, vibration-resistant fastener to help stop loose panels and rattling caused by a worn or missing nut. What it does:

• Secures panels, trim or small assemblies to mounting studs or shafts.
• Helps keep parts aligned and reduces vibration or rattling during operation.
• Common symptom: loose or shifting panels, audible rattling, or components that won't stay in place.
• Designed for a push-fit installation to replace worn or missing fasteners.

• Always disconnect power to the appliance before servicing.
• Push the nut fully onto a clean, undamaged stud until seated; replace damaged studs or mounting hardware.
• If needed, use pliers or a socket to press the nut on evenly—avoid deforming surrounding plastic or sheet metal.

This inner door panel restores the washer lid's interior finish and structural support, helping the lid close and seal properly. It replaces a cracked, dented, or cosmetically damaged inner door to improve appearance and function. What it does:

• Provides the interior surface and mounting points for the washer top lid assembly
• Restores proper lid alignment and helps the lid close smoothly
• Eliminates sharp edges or cosmetic damage from a cracked or dented inner door
• Helps maintain correct fit with the outer door and lid components

• One inner door panel

• Disconnect power and water supply before starting any repair
• Remove the outer lid and related fasteners to access and replace the inner panel
• Keep track of screws and clips; hand-tighten fasteners to avoid stripping

This retainer is a small mounting clip that secures internal components in place to prevent shifting and noise during operation. It restores proper alignment so panels or assemblies stay fastened and stable. What it does

• Holds a panel, trim, or internal component securely in its mounting location
• Prevents rattling, vibration noise, and loose or sagging parts
• Keeps connected parts aligned for reliable operation
• Commonly replaced when clip is cracked, broken, or missing

• One retainer clip

• Disconnect power before starting any repair
• Remove necessary panels or access covers to reach the damaged clip
• Replace the clip in the same orientation; avoid forcing parts to prevent damage
• If additional fasteners are damaged or missing, replace them as needed for a secure installation

This top panel is the exterior upper cover that protects internal washer parts and gives the appliance a finished look. It restores a secure mounting surface for the control area and helps keep water and debris out of the cabinet. What it does

• Covers and protects internal components at the top of the washer cabinet.
• Provides the mounting surface and alignment for the control console and lid.
• Restores appearance when the original panel is dented, cracked, or rusted.
• Reduces rattles or vibration caused by a loose or warped top.

• Disconnect power and water supply before starting any repair.
• Use basic hand tools; some screws or clips may need to be removed to lift the old panel.
• Handle edges carefully — metal panels can be sharp.
• Have a second person assist if needed to prevent bending or dropping the panel.

This dispenser handle assembly restores proper operation and control of your refrigerator's ice and water dispenser. It replaces a cracked, loose, or broken handle so you can dispense without difficulty and improve the dispenser's appearance. What it does

• Replaces damaged or cracked dispenser handle so the lever engages properly
• Provides a secure grip for activating the ice and water dispenser
• Helps stop wobbling or sticking that prevents consistent dispensing
• Restores alignment and tactile feedback for dispenser operation

• Disconnect power to the refrigerator before starting any work to avoid electrical hazard.
• Remove the old handle by accessing the dispenser trim and fasteners; retain mounting screws if reusing.
• Align the new handle, secure fasteners, and verify the dispenser lever moves freely and dispenses correctly.

This tub clamp secures a flexible seal or hose to the appliance's tub, maintaining a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop leaks and keep the tub joint stable during operation.

• Applies even clamping pressure around the tub connection
• Helps prevent water leaks at the tub-to-seal or tub-to-hose joint
• Restores proper fit when the original clamp is stretched, stripped, corroded, or missing
• Common symptoms: water at the base/front, loose seal or hose, visible clamp damage

• Disconnect power and turn off water before service
• Access the tub connection; remove the old clamp and inspect the seal/hose for wear
• Clean mating surfaces; seat the seal evenly, position the clamp, and tighten until snug without pinching the rubber
• Run a quick fill/drain test and check for leaks

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

This stator is the stationary motor component that creates the magnetic field needed for the washer's drive motor to operate. It restores motor function so the appliance can agitate and spin normally. What it does:

• Generates the magnetic field that interacts with the rotor to drive the motor.
• Enables proper agitation and spinning when the motor and rotor are functioning.
• Commonly replaced when motor runs poorly, makes unusual noises, or the washer fails to spin.
• Works as part of the motor assembly to maintain consistent motor performance.

• One stator

• Disconnect power and water supply before beginning any repair.
• Access typically requires removing the washer cabinet or motor housing; follow the service manual for your model.
• Inspect the rotor/motor and wiring for damage when replacing the stator.

This genuine mounting screw secures panels and components so assemblies stay aligned and rattle-free. Designed to replace worn or missing fasteners and restore proper fit and function. What it does:

• Secures panels, brackets or trim to prevent movement and vibration
• Restores proper alignment of assemblies that feel loose or shift
• Helps eliminate rattling, squeaks, or parts that fall away during use
• Matches OEM thread and head type for correct fit

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten which can strip threads or crack plastic
• Replace any additional damaged or missing fasteners for best results
• Disconnect power or follow appliance-specific safety steps before working near wiring or energized components

This transport cover secures internal components during shipping and service to prevent movement and damage. It helps keep parts aligned and reduces noise caused by loose components while the appliance is being moved. What it does:

• Holds internal components in place during transport to prevent shifting or impact damage
• Reduces rattles and vibration caused by unsecured parts
• Protects delicate assemblies from knocks during delivery or handling
• Helps maintain alignment of components until the appliance is installed

• One transport cover

• Disconnect power and water before servicing the appliance
• Remove all shipping brackets and covers per the owner's manual before normal operation
• Use manufacturer-specified fasteners and torque; do not force or modify the part

This small replacement clip secures panels, trim, or wiring so appliance components stay properly positioned and the unit operates quietly. A simple, low-cost part that prevents loose pieces from shifting or rattling during use. What it does

• Holds trim, panels or harnesses in place to prevent movement and noise
• Keeps wiring or small components secured to reduce wear from vibration
• Helps maintain proper alignment of plastic or metal assemblies
• Commonly used where a simple snap-in retainer is required

• One clip/retainer

• Disconnect power (and water if applicable) before servicing the appliance
• Inspect surrounding parts for damage; replace any cracked or broken mounting features
• Typically installs with pliers or by hand; avoid forcing to prevent breakage

The Console is an OEM part for Whirlpool washing machines. It houses the control panel and electronic components that operate the washer. The console provides an interface for selecting cycles and options while shielding internal mechanisms.

Symptoms of a bad console can include cracks, impact damage, or faulty electronic components like non-responsive buttons. 

 Causes of a bad console include normal wear and tear over time, moisture intrusion leading to corroded electronics, and accidental mishandling.

Symptoms of a bad console include:

• Buttons that do not work or selections that do not register  
• Loose or damaged door or interface paneling
• Error codes or cycling issues due to wire or component damage

Color: White

This Whirlpool replacement part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wire harness routes power and signal connections between an appliance's controls and components, restoring proper electrical continuity for normal operation. It replaces a damaged or worn harness to help resolve power and control issues. What it does:

• Provides the factory wiring connections between control boards, motors, and sensors
• Restores reliable power and signal paths when wiring is frayed, melted, or broken
• Can stop intermittent operation, failure to start, or control communication errors when caused by wiring faults
• Keeps wires organized and secured to prevent chafing and short circuits

• One complete wire harness as shown

• Disconnect all power (unplug or shut off breaker) before beginning work
• Transfer and align connectors exactly as removed; do not force mismatched plugs
• Route and secure the harness with existing clips or fasteners to avoid contact with hot or moving parts