Wm1163xvs1 Parts

Fix standing water, loud pump noise, or continuous filling in your washer. This drain pump motor assembly restores water removal. Moderate DIY repair.

This rotor assembly is the rotating half of your washer's direct-drive motor. It mounts to the rear of the tub and, working with the stator, spins the drum for wash and spin cycles to restore smooth operation.

• Couples with the stator to drive the inner tub during wash and spin
• Helps resolve no- or slow-spin complaints
• Can address a drum that won't turn or turns intermittently
• May reduce grinding/clicking from the rear caused by damaged rotor magnets

• Unplug the washer and turn off water supply before servicing
• Access from the rear; remove the center bolt and pull the rotor straight off the shaft
• Magnets are strong—keep fingers clear; align splines/keyway on reinstallation
• Tighten the center bolt securely and inspect the stator and sensor while open

This is the rubber door boot gasket (bellow) that creates a watertight seal between the front-loading washer drum and the door opening. It flexes during the wash cycle to contain water while allowing the drum to move. Replace this seal if you notice water leaking from the door area, visible tears or holes in the rubber, or mold and mildew buildup that cannot be cleaned.

Fix PE error codes and water overfilling issues with this pressure switch. Monitors tub water level to control fill and drain cycles. 30-minute DIY repair.

Replace your washer's door boot seal if you notice water leaks around the door or visible cracks in the rubber. Maintains watertight seal on front-load washers.

This is a rubber gasket that seals the washing machine tub to prevent water from leaking during wash and spin cycles. It fits around the tub opening and maintains a watertight barrier. Replace this seal if you notice water leaking from around the tub area, or if the gasket appears cracked, hardened, or deformed.

Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.

Fix a washer that won't fill with water or fills too slowly. This water inlet valve assembly controls water flow and prevents leaks. Direct fit.

This knob assembly replaces a worn or broken control knob so you can reliably set and adjust appliance settings. It restores a secure, easy-to-turn interface for the appliance's control shaft. What it does:

• Fits onto the control shaft to allow manual selection of settings and temperatures.
• Replaces cracked, stripped, or loose knobs that no longer grip the control shaft.
• Helps resolve issues where the control won't turn smoothly or slips while changing settings.
• Restores tactile feedback for accurate user control.

• Disconnect power to the appliance before removing or installing the knob.
• Pull the old knob straight off the control shaft.
• Align the knob's internal splines with the control shaft and push until fully seated.
• If knob does not seat or control still slips, inspect shaft splines and replace damaged components as needed.

This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:

• Fits over standard appliance leveling legs to raise or lower each corner
• Helps stabilize machines to prevent rocking and uneven operation
• Reduces vibration and noise caused by unlevel appliances
• Useful when installing, moving, or re-leveling washers and dryers

• Turn legs slowly and adjust one corner at a time until the appliance sits level.
• Unplug the appliance (and shut off gas supply for gas dryers) before performing major moves or checks.
• Use caution to avoid pinching fingers when lowering legs; keep hands clear of pinch points.
• Check for damaged feet or mounting hardware and replace as needed.

This accessory assembly is a genuine replacement component that restores the appliance's accessory fit and function. It installs in the accessory area to secure and connect related parts for reliable operation. What it does:

• Replaces a damaged or missing accessory assembly to restore proper attachment and alignment
• Secures accessory components so controls and moving parts operate smoothly
• Commonly used when accessories are loose, broken, or no longer seating correctly
• Helps prevent rattling, misalignment, or intermittent accessory-related issues

• Disconnect power (and water, if applicable) before starting any repair
• Basic hand tools are typically required; follow the appliance's service manual for exact steps
• Keep fasteners and small parts organized during removal and reassembly

This hinge spring restores proper tension to the door so it opens and closes smoothly and stays aligned. Replacing a fatigued spring helps prevent sagging or slamming and supports a consistent, reliable door close.

• Provides the return tension/counterbalance for the door hinge mechanism
• Assists smooth opening/closing and helps the door stay properly aligned when latched
• Helps maintain consistent closing force over time
• Failure symptoms include: door drops quickly, won't stay aligned or fully closed, weak/squeaking spring action

• Disconnect power before service; allow any hot surfaces to cool
• The hinge and spring are under tension—support the door and release/install tension carefully
• Note spring orientation and hole positions before removal; match them on installation
• Access may require removing trim or the door; keep fasteners organized for reassembly

Does not come with a hose or filter. These have to be purchased separately

These non-skid pads attach to the bottom of the washer's leveling legs to prevent the machine from sliding or walking across the floor during operation. They are made of durable rubber or similar grip material. Replace them if your washer vibrates excessively, moves out of position during spin cycles, or if the existing pads are worn, cracked, or missing.

Washer door won't stay closed or latch properly? This door latch hook secures your washer door, preventing accidental openings during cycles. Quick DIY fix.

Washer won't spin or agitate? A faulty stator assembly disrupts the magnetic field needed to drive the motor. Restores normal drum rotation.