Wm2020cw Parts

This is a spider arm assembly for washing machines. Another name for the spider is the rear tub support because it provides support for the outer tub. The spider has three legs that are approximately 10 inches long each. washing machines might need a new spider arm assembly if it is very noisy, if it shakes excessively while running, if the drum is emitting burning smells at high speeds, or if it is smoking. If upon visual inspection, the spider arm assembly is rusted or corroded, it will need to be replaced. The dryer drum may appear to have cracks, but this is how it is manufactured during the casting process. This is a genuine LG part and is an OEM part sourced directly from the manufacturer. It is sold individually. This specific spider arm assembly is compatible with washing machines that are LG and Kenmore manufacture.

This Screw (drawing) is a factory fastener used to secure appliance panels and components. Replacing a stripped, corroded, or missing screw restores a tight fit, reduces vibration, and helps keep assemblies correctly aligned.

• Secures panels, brackets, and mounting points as specified by the manufacturer
• Replaces screws that are lost, damaged, corroded, or stripped
• Helps address rattling, vibration, or loose-fitting parts caused by missing hardware
• Maintains proper alignment and stability of the assembly

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to its original location; start threads by hand to avoid cross-threading
• Use the correct driver; tighten snugly without over-torquing into metal or plastic
• Refer to your model's parts diagram to correct location and quantity

This Power Cord Assembly restores a secure, grounded connection from your wall outlet to the washer's internal power circuit. Replace a frayed or failed cord to resolve no-power issues and maintain safe operation. What it does:

• Delivers AC power from the wall outlet to the washer's internal power circuit (line filter/control)
• Provides a proper equipment ground path for the cabinet
• Replaces damaged or overheated cords that can cause power loss
• Common symptoms include: washer has no power, won't start, intermittent power when the cord is moved, or visible cord/plug damage

• 1 power cord assembly

• Disconnect the washer from power before servicing and verify the outlet/breaker are in good condition
• Access cord connections by removing the rear or top panel per your model's service information
• Note original routing and strain relief; reinstall clips/guides the same way to prevent chafing
• Secure the ground connection and fully seat all terminals; keep wiring clear of sharp edges before testing

The Drawer Front Panel Assembly is the complete replacement front for a pull-out drawer. It restores a clean look and solid handle support so the drawer opens and closes smoothly and sits flush again. What it does:

• Attaches to the drawer frame to provide the finished outer front
• Supports handle mounting and helps keep the drawer aligned
• Common fix for a cracked or dented front, broken mounting tabs, or a loose/missing panel
• Can help resolve a drawer that won't close flush or feels wobbly

• 1 drawer front panel assembly

• Disconnect power before servicing; remove items from the drawer to reduce weight
• Remove the handle and mounting screws; support the panel as you lift it off the drawer
• Transfer any reusable hardware from the old panel; align the new panel and tighten fasteners evenly
• Test drawer operation and fit; adjust as needed per service information

This hose clamp secures a rubber hose connection to prevent leaks where the hose meets its fitting. A tight, uniform seal helps maintain proper water flow and keeps the appliance operating reliably.

• Provides a tight, 360-degree seal around the hose barb/fitting
• Helps correct issues like water leaks at the hose connection point
• Maintains correct hose attachment during operation and vibration
• Step-less ear design distributes clamping force evenly

• Unplug power and shut off water supply before servicing
• Note clamp orientation and hose routing before removal
• Use appropriate ear-clamp pincers or pliers to compress the clamp evenly
• Check the hose and fitting for wear; replace if cracked or deformed

This inlet hose channels household water to the appliance's fill system. Replacing a worn or leaking hose restores proper water flow and helps protect floors and internal components from water damage.

• Directs water from the household supply to the unit's inlet/fill assembly
• Maintains a watertight path to prevent drips and leaks
• Replaces hoses that are cracked, swollen, kinked, or mineral-fouled
• Common symptoms: leaks at fittings or beneath the unit, slow or no fill, intermittent filling, or water-related error messages

• Disconnect power and turn off the water supply before servicing
• Place a towel or pan to catch residual water and relieve line pressure slowly
• Route the hose without kinks; ensure sealing surfaces and/or washers are clean and properly seated
• Secure connections per the OEM design (compression fitting or clamp); restore water and check carefully for leaks on the first run

This multi-wire harness connects the washer's control system to multiple components. Replacing a damaged harness restores reliable power and signal routing and can help resolve intermittent operation, error codes, or no-spin/no-drain conditions caused by broken or burnt wires.

• Distributes electrical power and control signals between the PCB and components such as the motor, drain pump, inlet valves, sensors, and door lock
• Provides factory-terminated, keyed connectors and correct routing paths for secure, plug-in connections
• Typical failure symptoms: won't start or intermittent operation, component-related error codes, no spin/drain/fill, or visible heat damage to wires/connectors
• Using the exact harness maintains proper connector types and lengths for your appliance's design

• Disconnect power and turn off water supply before servicing
• Access the harness by removing panels as needed; take photos to document original routing and connections
• Transfer plugs one at a time; match keyed connectors and do not force them into place
• Secure the new harness under factory clips and away from sharp edges or moving parts; test operation before reassembly

This gasket does not include the port. For the gasket with a port order MDS33059402.

This washer rotor assembly mounts on the direct-drive motor and works with the stator to turn the basket. Replacing a worn rotor restores smooth tumbling and full spin performance when the drum won't turn or makes harsh scraping noises.

• Works with the stator to create the magnetic drive that spins the wash basket
• Helps when the washer won't spin or tumble, or only reaches a weak/erratic spin
• Can reduce grinding/scraping noises from the rear of the tub
• Addresses slippage from worn splines or a damaged magnet ring on the rotor

• Disconnect power and turn off water before servicing
• Access the rotor at the back of the tub; remove the rear cover if present
• Support the rotor, remove the center bolt, and pull the rotor straight off; magnets are strong
• Align splines, seat the new rotor fully, start the bolt by hand, and tighten to the manufacturer's specification

Replacement knob assembly that restores control and precise selection of settings on your appliance. Fits the original control shaft and provides a secure grip for adjusting temperature, cycle, or power settings. What it does

• Restores user control when the original knob is cracked, melted, stripped, loose, or missing.
• Provides a clear indicator/pointer for accurate selection of settings.
• Matches original fit and function to prevent slipping or uneven engagement with the control shaft.
• Helps resolve symptoms like a knob that won't turn, slips on the shaft, or has a broken pointer.

• Always disconnect power to the appliance before servicing; shut off gas supply for gas ranges.
• Typically installs without tools—remove the old knob by pulling it straight off, then press the new knob onto the control shaft.

Comes in a pack of four.

This door hinge bracket mounts the hinge to the washer's front cabinet, keeping the door aligned so it closes and seals properly. A bent or broken bracket can lead to door sagging, poor latching, or leaks at the door.

• Secures the door hinge to the washer's front panel/cabinet
• Supports door weight to maintain alignment
• Helps preserve proper door-to-gasket contact for sealing
• Typical symptoms: door sags or rubs, won't close/latch, or water leaks at the door

• Disconnect power and shut off water before servicing.
• Support the door before removing hinge/bracket screws to prevent strain.
• Transfer the hinge to the new bracket and reinstall using existing hardware.
• Align the door and ensure latch engagement and gasket seal before fully tightening.

This inlet hose supplies fresh water from the household line to the dishwasher. Replace a damaged or leaking hose to help restore proper filling and prevent water leaks during operation.

• Channels water from the supply valve to the dishwasher's inlet
• Common failure signs: leaks under or behind the unit, fill errors, slow or no fill
• Helps resolve intermittent water supply issues caused by a kinked or cracked hose

• Unplug power and shut off the water supply before starting
• Place a towel or pan to catch residual water when disconnecting
• Check for leaks after installation and tighten connections as needed

The door boot gasket seals the opening between your front-load washer's door and outer tub, keeping wash water contained. Replace it if the boot is torn, deformed, or heavily mildewed to restore a reliable, watertight seal.

• Forms a watertight seal between the outer tub and door opening
• Prevents leaks from the front of the washer during wash and spin
• Flexible design maintains the seal as the drum moves
• Common failure signs: water on the floor at the front, dripping at the door, visible rips/cracks, or the boot pulling loose

• Unplug the washer and turn off water supply; wear gloves to avoid sharp edges
• Access the boot by removing panels as required for your model; note hose positions and alignment
• Release the outer and inner retaining clamps/springs and remove the old gasket
• Seat the new gasket evenly, align indexing features/ports, reinstall clamps securely, and run a quick test for leaks

This hose connector joins two internal water lines inside your washer to create a secure, leak-resistant connection. Replacing a worn coupler helps stop drips and keeps water moving properly during fill, wash/recirculation, and drain cycles.

• Joins two hoses inside the appliance for a tight, reliable seal
• Helps maintain proper water flow during operation
• Replace if cracked, deformed, or if hoses slip off despite clamp tension

• Unplug the washer and turn off water supply; expect some residual water
• Access the hose junction and note hose routing and clamp positions
• Fully seat hoses onto the connector and secure clamps behind the hose bead
• Reassemble and run a short test cycle while checking for leaks

This inlet hose is the internal water line for your dishwasher, routing fresh water from the fill valve into the wash system. Replacing a brittle or leaking hose restores reliable filling and helps protect floors and cabinetry from water damage.

• Channels incoming water from the inlet valve to the tub/sump
• Maintains proper fill level and flow at the start of each cycle
• A cracked, kinked, or loose hose can cause leaks or slow/no fill
• Restores correct water delivery and helps prevent water damage

• Disconnect power and shut off the water supply before servicing
• Pull the dishwasher forward for access; place a towel or pan to catch residual water
• Note the original routing and clamp positions; transfer clamps and avoid kinks
• Restore water, run a quick fill cycle, and check all connections for leaks