We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Mounts the door hinge to your washer's front cabinet. Replace if bracket is bent, broken, or missing to restore proper door alignment and sealing.
Bought two new ones and screwed them in. Read more
This is the internal fill hose that connects the water inlet valve to the wash tub inside the washing machine, delivering cold water during the fill cycle. It is a rubber or reinforced hose with fittings on each end. Replace this hose if you notice leaking underneath or behind the washer, or if the machine is not filling properly with water.
Comes in a pack of four.
Installed the leg assembly and adjusted them to where the washer would not shake. Read more
Replace your broken or missing range clock knob. Mounts to the control panel for adjusting the built-in clock. Order a new knob if yours is cracked or worn.
Mounts to the washer's lower frame to secure components and maintain alignment. Replace if bracket is cracked, broken, rusted, or missing hardware.
Replaced leg mount and leg. Read more
A shoulder screw that secures appliance components and provides a precise pivot or spacer point. Replaces a missing or worn screw to restore alignment, reduce rattling, and keep panels and assemblies securely in place. What it does:
I had to remove the oven door, which I learned is made to come off without tools. Then took out the bottom by removing two screws and lifting. Removed the screws attaching the igniter, pulled wires thru back until I could get the connector and disconnect. When the new igniter arrived, I had to change the connector. I cut the one off the old one, and spliced to the new one using solder and shrink tubing. Just reverse the procedure to install. I replaced the screws with new ones. Read more
Secures hose connections to maintain watertight seals in your washer. Replace if you notice leaks or loose hoses during operation. Verify fit with model number.
Replacement mounting screw secures panels, brackets, and trim to the appliance frame. Needed when original screw is stripped, missing, or damaged.
If your oven overheats or shows temperature errors, this temperature probe restores accurate heat sensing. Simple DIY fix in 15 minutes or less.
Common sense and following directions from a tech, Read more
Replaces the front outer tub cover that houses the door boot seal and aligns the spin basket. Order a new cover if yours is cracked or worn from use.
The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more
This 10-32 x 3/8 machine screw secures appliance components. It keeps panels, brackets, and trim firmly attached so everything stays aligned and quiet during operation.
Sheet metal pan head screw secures panels, brackets, and components to appliance cabinets. Replace missing, stripped, or corroded screws to restore fit.
I ordered and replaced the old ignitor and the corroded mounting screws. Read more
Secures rubber hoses to fittings with constant spring tension to prevent leaks. Replace when rusted or weakened to maintain a tight seal. Confirm fit.
Hex head sheet metal screw secures appliance panels, brackets, and trim. Replace missing, stripped, or damaged screws to keep covers firmly attached.
This rotor assembly is the rotating half of your washer's direct-drive motor. It mounts to the rear of the tub and, working with the stator, spins the drum for wash and spin cycles to restore smooth operation.
Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.