Wm2hm101 Parts

This tub-to-pump hose connects the washer's outer tub to the drain pump, carrying water out during the drain cycle. Replace it to resolve leaks or drain errors caused by cracks, splits, or internal blockages.

• Routes wash water from the outer tub to the drain pump
• Flexible bellows section helps prevent kinking and accommodates tub movement
• Failure signs: water leaking under the washer, slow/no draining, drain-related error codes, or visible cracks/soft spots
• Often needed after clamp corrosion, physical damage, or age-related deterioration

• Unplug the washer and turn off water supply; drain any remaining water from the tub/hoses
• Access location varies by model; remove panels as needed to reach the hose and clamps
• Use pliers to release spring clamps; note routing and clamp orientation before removal
• Seat the hose fully on fittings, secure clamps, and test with a short drain/rinse cycle to check for leaks

Replaces the front outer tub cover that houses the door boot seal and aligns the spin basket. Order a new cover if yours is cracked or worn from use.

This is a plastic lifter baffle that mounts inside the dryer drum. It tumbles and lifts clothes as the drum rotates, promoting even airflow and efficient drying. Replace this part if it is cracked, broken, or missing, which can result in clothes bunching together, uneven drying, or loud thumping noises during operation.

Snaps into open holes on washer cabinet to restore finished appearance and keep out dust and lint. Replace missing or damaged caps. Confirm fit with your model number.

Fix a blank, dim, or flickering display panel with this washer control board. Restores front-panel settings and status indicators when controls stop responding.

Locking pin for shock absorber.

Fix excessive washer vibration and loud spinning with a new balance weight. Stabilizes the tub during spin cycles. Moderate DIY repair for most models.

Secures the door boot to the front panel, creating a watertight seal. Replace if the boot shifts, separates, or leaks during cycles. Verify fit with your model.

Fix washer that won't start, shows error codes, or stops mid-cycle. This main control board manages all wash functions. Moderately difficult repair.

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

Pivot hanger assembly that supports and stabilizes washer components. Replace if worn, damaged, or causing misalignment to restore smooth movement.

Replacement wire harness for washers. Restores electrical connections between components when original wiring is damaged, frayed, or corroded. Direct fit.

This spring-tank is the replacement spring assembly used to restore proper door balance and movement. It helps the appliance door open and close smoothly and prevents sudden drops or heavy lifting. What it does

• Provides counterbalance tension for the appliance door to control opening and closing motion
• Reduces sagging or slamming of the door caused by worn or broken springs
• Restores smooth, even movement when the door feels heavy or uneven
• Works as a direct-fit replacement when the original spring assembly fails

• One spring-tank

• Disconnect power and water to the appliance before starting any repair
• Handle spring components carefully; springs are under tension and can cause injury if released unexpectedly
• Use proper tools and follow manufacturer instructions or a service manual for safe removal and installation

Interior support trim that secures the door assembly and provides a finished surface inside your washer door. Replace when cracked, damaged, or worn.

Rear housing panel that shields internal components and maintains airflow. Replace this outer cover if cracked, broken, or missing to restore protection.