Wmh2175xvb-2 Parts

This thermistor is a refrigerator temperature sensor that monitors internal air temperature so the control board can regulate cooling. Replaces a failed sensor to help restore accurate temperature readings and more consistent cooling. What it does:

• Senses internal refrigerator temperature and sends a variable resistance signal to the control board
• Helps the control system cycle the compressor and fans correctly for stable temperatures
• Commonly replaced when refrigerator runs too cold, too warm, or has irregular cooling cycles
• Can address temperature-error codes or defrost control issues when the sensor is faulty

• Disconnect power to the appliance before inspecting or replacing the sensor
• Handle the sensor and wiring harness carefully to avoid damage to the probe or connectors
• Install in the original sensor mounting location and secure wiring away from moving parts

This base is the appliance's lower cabinet section that supports internal components and helps stabilize the unit. It restores a solid foundation so the appliance sits level and protects internal parts from floor contact and debris. What it does:

• Provides structural support for the appliance's internal assemblies and controls
• Helps stabilize the unit and reduce excessive vibration or rocking
• Protects wiring, motors and other components from contact with the floor
• A damaged or cracked base can cause noisy operation, misalignment, or uneven sitting

• Disconnect power (and gas if applicable) before beginning any repair
• Follow the OEM service manual for disassembly and reassembly steps
• Replacement may require removing the cabinet and/or drum; having a second person helps with lifting and alignment
• Inspect and reuse original fasteners only if undamaged; replace any worn mounting hardware

This replacement screw is a general-purpose fastener used to secure exterior panels, trim, or internal components on compatible Whirlpool appliances. It restores proper fit and reduces rattles or loose parts for a safer, more reliable appliance. What it does:

• Secures panels, trim pieces, or mounting brackets to keep components in place
• Prevents vibration-related noise and movement caused by missing or loose fasteners
• Helps maintain alignment of control panels and exterior housings
• Replaces stripped, corroded, or lost screws to restore original fit

• Use the correct screwdriver or bit to avoid stripping the head
• Match screw length and thread engagement with the original for a secure fit
• Tighten to snug only; over-tightening can strip threads or crack panels
• Disconnect power before performing repairs on electrical components

This wire harness assembly routes power and control signals between the appliance's main control and its components to restore reliable electrical connections. It replaces a damaged or intermittent wiring assembly to help components receive proper power and signals. What it does

• Connects the main control to heating elements, sensors, switches, or other components depending on appliance model
• Restores lost or intermittent power/signal paths caused by frayed, burned, or broken wires
• Helps resolve symptoms like components not powering, intermittent operation, or electrical arcing at connection points
• Maintains correct wire routing and connector fit for safe operation when installed properly

• Disconnect all power (unplug or switch off breaker) before beginning work
• Photograph existing routing and connector locations to ensure correct reinstallation
• Route harness without pinching; secure with original clips or ties and avoid heat sources

This replacement mounting plate secures internal components so the appliance operates quietly and stays aligned. Replacing a damaged or bent plate helps stop rattling, prevent part movement, and restore proper fit between adjoining parts. What it does:

• Provides a stable mounting surface for nearby components and fasteners
• Prevents parts from shifting or vibrating during operation
• Helps eliminate rattling or noise caused by a loose or bent plate
• Restores correct alignment where the original plate was damaged or deformed

• One replacement plate

• Disconnect power (unplug appliance or turn off circuit) before starting any repair
• Wear gloves and eye protection; edges may be sharp
• Use correct fasteners and torque to avoid bending the new plate;

This stainless-finish door handle restores a solid, comfortable grip for opening and closing the appliance door. Replace a cracked, loose, or worn handle to keep the door operating safely while maintaining a matching stainless appearance.

• Provides a secure handhold to open and close the door
• Restores safe, reliable access when the original handle is cracked, loose, or missing
• Matches stainless-finish appliances for a consistent look
• Common signs: wobbling handle, broken mounting points, difficulty opening the door

• Disconnect power before servicing; allow any hot surfaces to cool
• Access the handle mounting screws; on many models, the inner door panel or trim must be removed
• Transfer any end caps, spacers, or trim from the original handle if required
• Tighten screws evenly and verify alignment and proper door operation after installation