Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Size: 10-12 a. Includes 12 screws.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
This locking clip secures a mating part—often a control knob—onto its shaft on select laundry appliances. Replacing a worn or missing clip restores a tight fit so controls stay in place and operate as intended during use.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Double-style bushing supports the washer lid hinge pin. Replace worn or cracked bushings to restore smooth, quiet lid operation and proper alignment.
Not hard when you have videos and a mechanical background....piece of cake.... Read more
Cushions where the washer lid meets the top panel to soften closure and protect the finish. Replace worn, cracked, or missing bumpers to reduce noise.
The problem was most likely the evaporator fan motor but it could have been a bad blade, loose parts or bad motor mounts. Hard to tell without taking everything apart and inspecting. Since fridge was 17 years old I decided to order the entire evaporator fan assembly as shown in the parts diagram including fan blade, motor brackets, motor, motor mounts, screws, etc. Getting to the assembly involved removing the ice maker unit plus the entire rear inside of the freezer section. Parts cost around... Read more
Adjustable leveling leg threads into washer base to stabilize cabinet and reduce vibration. Replace if cracked, broken, or missing for proper support.
Took the old leveling legs out and put the new ones in Read more
Replaces a cracked or leaking wash tub to restore water containment and drum support. Fixes leaks, rubbing noises, and vibration. Confirm fit by model.
I ordered a new mode selector and new tub bearing. Upon disassembly, I noticed that the plastic outer tub had actually heated up around the tub bearing and tub seal area, such that the new tub seal did not fit tightly. I ordered a replacement outer tub, and reassembled all the new parts. During assembly, I installed the new tub seal upside down, but recognized it while re-watching the how-to video. I pulled the assembly back off and flipped the seal over, then reassembled it again. I also put... Read more
Plastic bushing that fits inside your washer's lid hinge for smooth pivoting. Replace if worn, cracked, or causing lid misalignment and squeaking.
Secures the drive pulley to the transmission shaft in top-load washers. Replace if the original nut is backing off, stripped, or missing.
Size: 14-10 a trt 7/8 s.
Replaced the hub nut, tub bearing split ring, tub seal, hub washer and agitator coupler. I watched multiple times the APP video. It was extremely helpful and I would not have attempted this without seeing the video. I had a lot of trouble getting the hub nut off. I used an 1 5/8" 6 point strike box wrench and a 4# hammer to get it off. I sprayed it with WD 40 5 or 6 times over of the course of a week to let it soak. I finally got it off. Had I known that the shaft is not round I would have... Read more
12-pack of inlet hose washers for washers and washer dryer combos. Replace cracked, worn, or missing washers to prevent leaks at water connections.
I called on your service, a person on the phone name Mr.Berry ask what the matter was . I told him the said a water valve should fix it . it sure was the right fix. thank you guys and thank you Mr. Berry. john m Read more
Fixes washer not spinning fast enough or motor failure. This 2-speed direct drive motor restores proper agitation and high-speed spin cycles. Moderate DIY.
Size: 8-32 t. Includes 12 screws.
Mounting screw for refrigerators, dryers, and washers. Replaces lost, stripped, or corroded screws during repairs or part installations.
Piece of cake...replaced bearing support and bearing glides. Video helped. Only issue is unclear about what glides need to be ordered and where they go. Had to look at another sight video. Grey glides go on top and nylon glides go on each side at the bottom. So you order two grey and two white glides. You also need a TORX driver to get the control panel free. So this and a Phillips Head #2 screwdriver and you are home free. Read more
This shipping bar assembly secures the oven door and internal components during transport to prevent movement and damage. Replacing a damaged or missing shipping bar helps ensure the range or oven door stays protected while moving the appliance. What it does:
Snap-in plastic clip cover that conceals fasteners and secures panels on your top-load washer. Replace if broken or missing to restore appearance.
A single replacement screw used to secure appliance panels, trim, and internal brackets so components stay aligned and reduce rattling. Simple, direct-fit fastener for restoring proper mounting and stable operation. What it does: