Wrs322fd Parts

This door hinge mounts at the bottom of the freezer door, supporting its weight and providing the pivot point for smooth operation. Replacing a worn hinge restores proper alignment and sealing to help prevent frost and temperature issues.

• Supports the freezer door at the lower pivot for smooth opening and closing
• Helps maintain door alignment so the gasket seals correctly
• Wear can lead to sagging, rubbing, or gaps along the hinge side
• Helps resolve poor sealing, frost buildup, or the door popping back open

• Disconnect power and remove the base grille before servicing
• Support the door to prevent dropping; mark hinge position for easier realignment
• Remove hinge screws; transfer any shims/spacers from the old hinge to the new one
• Reinstall, tighten fasteners, and check door swing and gasket contact; adjust as needed

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

Made by Whirlpool. This kit includes 15 feet of copper tubing, saddle valve, teflon tape, and tubing connector. Use this kit to connect your refrigerator ice maker to water supply (usually your water shut off valve under the kitchen sink).

This factory screw secures appliance components, panels, and brackets. Replace a missing, stripped, or corroded fastener to restore a snug fit, reduce rattles and vibration, and keep assemblies properly aligned.

• Secures panels, brackets, and internal components in place
• Helps maintain correct alignment and clearances
• Replaces damaged, rusted, or missing screws
• Can help reduce rattling, vibration, or loose-fitting parts

• Disconnect power and shut off water/gas before servicing
• Match this screw to the original location; replace like-for-like
• Start threads by hand and use the correct driver to avoid cross-threading
• Tighten snugly; do not overtighten, especially into plastic or thin sheet metal

This outer cabinet housing provides structural support and protection for internal components, helping maintain panel alignment and prevent damage from dust, moisture, or impact — replace a damaged housing to restore fit and protection. What it does:

• Supports and secures internal parts and exterior panels to keep components properly aligned.
• Protects wiring, controls and mechanical parts from dust, moisture and accidental contact.
• Helps reduce vibration and rattling by maintaining proper cabinet fit.
• Commonly replaced when the housing is cracked, warped, rusted or no longer secures internal components.

• Disconnect the appliance from power (and water supply if applicable) before beginning any work.
• Remove access panels and fasteners; support the assembly during removal to avoid damage to attached parts.
• Inspect and replace any worn gaskets, clips or fasteners; reuse parts only if undamaged.

Size; 8-18 x 1/2 inch.

Approximate measurement: 13.5" x 9.5"

This genuine OEM return spring restores proper return/tension for the appliance component it connects to, helping controls, latches or hinges snap back into place. Replacing a worn spring can stop sticking, sagging or failed return action. What it does:

• Provides tension to return a lever, latch or door component to its resting position
• Restores crisp return action when a control or hinge feels loose or fails to snap back
• Helps reduce rattling or intermittent contact caused by a weak or broken spring
• Functions quietly once replaced, improving normal operation of the affected mechanism

• Disconnect power and gas before servicing; follow appliance-specific safety instructions
• Springs can be under tension — use proper tools and caution to avoid injury or part damage
• Compare the old spring to the new one for correct length and end type before installation

This ice door replaces the chute cover that opens and closes during ice dispensing, helping keep cold air in the freezer and preventing spills. Restores proper ice flow and helps stop warm air and odors from entering the ice bin. What it does:

• Acts as the moving cover for the ice dispenser chute to control ice release
• Helps maintain freezer temperature by sealing the dispenser opening when closed
• Prevents moisture, debris, and kitchen odors from entering the ice compartment
• Can resolve symptoms like ice jamming, sticky or non-closing dispenser door, or unusual freezer air exchange

• One ice door (single chute cover) as shown

• Disconnect power to the appliance before beginning any work
• Remove ice bin and any obstructing shelves or panels
• Handle plastic parts carefully to avoid cracking; use proper tools for fasteners
• If door does not align after install, check linkage/hinge and adjust per instructions

This freezer shelf mounting cup fits into the liner opening to support the ribbed freezer shelf post, keeping the shelf level and secure. Replace cracked or missing cups to restore proper shelf support and prevent sagging.

• Supports the ribbed freezer shelf post and anchors it in the liner
• Helps keep the shelf level and properly positioned
• Replaces cracked, worn, or missing cups
• Common symptoms: shelf tilts, won't stay in place, rattles, or falls

• Unplug the refrigerator before starting
• Remove the freezer shelf; carefully pry the old cup straight out of the liner opening to avoid damage
• Press the new cup fully into the opening until flush; reinstall the shelf post into the cup
• Verify the shelf is seated and level before loading items

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

The Door-Ice is an OEM part for Whirlpool refrigerators. It provides access to the freezer compartment where ice is stored and produced. The door is fitted with a durable gasket and hinges to open and close securely whilst retaining cool air inside.  

Causes of a bad door can be damage to the gasket seal from over closing, cracks or punctures in the door compromising insulation, or worn or loose hinges allowing air flow.

Symptoms of a bad freezer door include:

• Difficulty opening and closing or failure to latch securely
• Accumulation of frost or ice buildup along door edges
• Cooler air leakages observed around the door seal

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This condenser fan motor bracket secures the condenser fan motor to the appliance chassis, keeping the cooling fan stable so it can move air across the condenser for proper cooling performance and prevent wobble or contact. What it does:

• Holds the condenser fan motor in the correct position so the fan blades clear surrounding components.
• Stabilizes the motor to reduce vibration and noise caused by a loose or damaged mount.
• Helps maintain proper condenser airflow to avoid overheating or reduced cooling.
• Can be replaced when the original bracket is bent, cracked, or broken and no longer supports the motor.

• Disconnect power before starting any repair to avoid electric shock.
• Verify motor and fan assembly alignment when reinstalling the bracket; secure mounting hardware snugly but do not overtighten.
• Inspect related fasteners and fan components for wear and replace as needed.

This clip kit secures small panels, wiring harnesses, or trim on compatible Whirlpool appliances to prevent rattling and keep components in their intended position. It restores proper fit and helps reduce noise from loose parts. What it does:

• Holds wiring harnesses and cables in place to prevent chafing or contact with moving parts
• Secures panels, trim, or hoses so assemblies stay aligned and quiet
• Reduces rattling, buzzing, or vibration caused by loose components
• Keeps parts positioned during normal use and transport

• Disconnect power (unplug or shut off breaker) before starting any repair
• Use basic hand tools; avoid forcing clips into place to prevent breakage
• Replace any damaged clips with the exact kit to ensure proper fit
• Re-check that fastened parts are secure and that there are no pinched wires before restoring power

This air diffuser cover directs and protects airflow within the appliance, restoring proper air distribution and sealing the diffuser opening. It replaces a cracked, missing, or worn cover to help maintain consistent performance. What it does:

• Covers and protects the air diffuser/vent opening from debris and damage
• Directs airflow for consistent circulation where required by the appliance
• Helps reduce air leaks that can cause uneven temperature or performance
• Replaces damaged or missing covers that may rattle or allow debris entry

• One air diffuser cover

• Disconnect power to the appliance before beginning service
• Remove any retaining screws or clips and carefully snap or slide the old cover out
• Install the replacement by aligning tabs or screw holes and securing per the OEM fit

Color: White. Size: 13 oz. Spray paint primer. can.