Wrs571cidmoo Parts

A direct-replacement electrical socket that restores a secure connection for a single appliance component. Replacing a worn or damaged socket helps stop intermittent power, flickering lights, or loss of function in affected circuits. What it does:

• Provides a secure electrical connection between the appliance wiring and the component it serves.
• Holds and aligns the mating connector or bulb so contacts meet reliably.
• Restores consistent power transfer when a brittle, corroded, or loose socket causes intermittent operation.
• Common symptom: component or light works intermittently, only when jostled, or not at all.

• One replacement socket

• Always disconnect power (unplug appliance or shut off breaker) before inspecting or replacing electrical parts.
• Inspect surrounding wiring and connector for heat damage; replace harnesses if insulation is compromised.
• Use basic hand tools to remove and reinstall; ensure contacts are fully seated and fasteners are secure.

This short electrical wire jumper completes a circuit between adjacent connector pins to restore power or signal continuity where a dedicated harness jumper is required. It's a simple replacement for worn, broken, or missing jumpers. What it does

• Bridges two connector points to complete a circuit or bypass a failed trace
• Restores power or signal flow to components that rely on a jumper connection
• Can resolve intermittent connections caused by damaged or corroded wiring
• Used where a short lead is needed to replace a missing or compromised factory jumper

• Disconnect power to the appliance before servicing to avoid shock or damage
• Verify correct connector orientation and secure fit; avoid forcing terminals
• Route jumper clear of moving parts and hot surfaces to prevent wear or melting

This trim pan is a molded replacement trim piece that restores the lower exterior appearance and helps channel minor drips away from the appliance base. It provides a clean, finished look and replaces damaged or missing trim. What it does:

• Replaces a cracked, warped or discolored lower trim that affects appearance
• Helps direct incidental moisture away from the cabinet base
• Restores the factory fit and finish at the appliance front/bottom
• Prevents sharp edges or gaps that can catch dirt or debris

• Disconnect power to the appliance before starting work to avoid electrical hazard
• Basic hand tools are typically required; remove fasteners or clips holding the old trim and snap or screw the replacement into place
• Handle plastic trim carefully to avoid scratching; align clips or tabs before applying pressure
• If you encounter unexpected corrosion or additional damage, stop and inspect for related repairs

This is a control board assembly for a refrigerator. This part acts as the hub of many critical functions that affect the refrigerator's performance. It manages temperature control, as well as fan control, ensuring the refrigerator keeps a consistent, safe temperature. It also ensures the refrigerator defrosts appropriately.If the refrigerator is no longer managing its temperature properly, if it runs constantly, or if it never defrosts, the control board may need to be replaced. When replacing the main control board, first ensure the refrigerator is unplugged from the wall, and that all food is safely stored elsewhere. A nut driver set and protective gloves should be worn when completing this repair.This main control board works for Whirlpool, Maytag and Kenmore refrigerators, and it is sold as a single item. This part is directly sourced from the manufacturer, and is an authentic OEM replacement part.

This cover corner replaces a missing or damaged corner trim piece to restore the refrigerator's interior/exterior finish and help keep shelves and bins seated properly. It provides a clean, finished look and protects edges from wear. What it does:

• Replaces the corner trim/filler that covers panel edges or joins interior liners
• Helps keep adjoining panels, shelves or bins aligned and reduces gaps
• Restores appearance after chipping, cracks or impact damage

• Designed for drop-in or snap-on installation; verify fit against the appliance before final assembly
• Use basic hand tools; avoid excessive force which can crack plastic parts
• Disconnect power if removing interior panels or working near electrical components

This 1/4-20 screw is a direct replacement fastener used to secure appliance panels, brackets, and assemblies. It restores proper fit and prevents rattling or loose components for safe, reliable operation. What it does:

• Fastens panels, mounting brackets, and components in place
• Replaces missing or stripped screws that cause loose or rattling parts
• Maintains alignment of assemblies to prevent wear and vibration
• Works wherever a 1/4-20 machine screw is specified by the manufacturer

• Disconnect power and follow the appliance manufacturer's safety instructions before servicing
• Use the correct-size driver or socket to avoid stripping the head
• Do not overtighten; snug until secure to avoid damaging threads or components
• If the original screw was rusted or seized, apply penetrating lubricant and use proper extraction tools

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

This aerosol spray paint restores the graphite finish on appliance surfaces for quick, low-effort cosmetic touch-ups. Use it to cover small chips, scratches and scuffs so the exterior looks uniform again. What it does:

• Matches graphite appliance finishes for spot repairs and touch-ups
• Covers visible chips, scratches and minor surface scuffs
• Restores a uniform appearance on painted metal appliance surfaces
• Helps protect exposed metal from surface corrosion after repair

• Clean and dry the surface; remove grease, dirt and loose paint before spraying
• Shake can well and test spray on a scrap piece or inconspicuous area first
• Apply in light, even coats from a recommended distance; allow coats to dry between passes
• Use in a well-ventilated area, keep away from heat/open flames, and follow all safety and disposal instructions on the can

This wire harness routes power and control signals between the appliance control and components to restore reliable electrical connectivity. It replaces damaged or burned wiring to help resolve intermittent operation and loss of function. What it does:

• Provides organized, insulated wiring to connect the control board to heaters, motors, sensors and switches.
• Restores continuity where frayed, pinched or burned wires cause faults or shorts.
• Common symptoms this can address: control panel unresponsive, appliance won't start, intermittent power or components not operating.
• Designed to follow factory routing and connector positions for correct fit and electrical function.

• Disconnect all power before replacing any wiring; verify power is removed at the breaker or unplug the appliance.
• Take photos or mark connector positions before removal to ensure correct reconnection.
• Avoid pulling on individual wires; remove and install at the connector housings to prevent terminal damage.
• If wiring is severely corroded or connectors damaged, inspect adjoining components and replace per service manual.

This replacement water dispenser valve tube routes water from the dispenser valve to the dispenser outlet so your appliance can deliver water and ice correctly. It restores a proper, leak-free flow path for the dispenser. What it does:

• Connects the dispenser valve to the dispenser outlet, directing water flow for dispensing and ice-making functions
• Replaces cracked, pinched, or deteriorated tubing that can cause leaks or weak/blocked water flow
• Helps stop visible leaks under the dispenser area and restore normal dispensing performance
• Compatible with factory valve connections and dispenser fittings when the OEM tube is specified

• One replacement water dispenser valve tube

• Disconnect power and shut off the water supply before starting work
• Inspect matching fittings and clamps; reuse only if undamaged — replace clamps if corroded
• Route the tube following factory routing to avoid kinks and ensure secure connections

This clip kit secures small panels, wiring harnesses, or trim on compatible Whirlpool appliances to prevent rattling and keep components in their intended position. It restores proper fit and helps reduce noise from loose parts. What it does:

• Holds wiring harnesses and cables in place to prevent chafing or contact with moving parts
• Secures panels, trim, or hoses so assemblies stay aligned and quiet
• Reduces rattling, buzzing, or vibration caused by loose components
• Keeps parts positioned during normal use and transport

• Disconnect power (unplug or shut off breaker) before starting any repair
• Use basic hand tools; avoid forcing clips into place to prevent breakage
• Replace any damaged clips with the exact kit to ensure proper fit
• Re-check that fastened parts are secure and that there are no pinched wires before restoring power

A small replacement pin that secures the flipper emitter assembly, restoring correct movement and alignment so the flipper can engage and operate reliably. Ideal when the original pin is bent, worn, or missing. What it does:

• Holds the flipper emitter or lever in place so the mechanism can pivot correctly
• Restores proper movement when a loose or broken pin causes misalignment
• Helps stop clicking, scraping, or intermittent operation related to a damaged fastener
• Serves as a direct-fit replacement designed for the OEM emitter/lever assembly

• One replacement pin as shown

• Disconnect power to the appliance before beginning any repair
• Handle small parts carefully; keep screws and pins organized during disassembly
• Use basic hand tools; no special tools or adhesives are typically required

This grille fits over the drip tray to protect internal components and help catch spills, keeping the cooktop area cleaner and easier to maintain. It restores proper fit and appearance when the original grille is damaged. What it does:

• Covers and protects the drip tray from food and liquid spills
• Helps contain messes so spills are easier to wipe away
• Prevents debris from contacting components beneath the cooktop
• Addresses symptoms like visible damage, warped or missing grille, and recurring food buildup

• One grille/drip tray cover

• Disconnect power to the appliance before attempting any service
• Remove surrounding components to avoid damage
• Handle carefully to avoid bending or scratching the grille
• If hardware is not visible, verify if existing clips or screws are reused; only parts explicitly listed ship

Color: White. Size: 13 oz. Spray paint primer. can.

This steel rivet secures appliance panels and small components, restoring proper fit and preventing rattles or loose parts. It's a straightforward replacement when a worn or missing rivet causes instability. What it does

• Fastens sheet metal or trim pieces to the cabinet or internal brackets
• Restores secure mounting when a previous rivet has sheared or fallen out
• Stops panel vibration or rattling caused by a loose fastener
• Provides a permanent, non-threaded mechanical connection for components

• Replacement typically requires a rivet tool or rivet setter; drill-out may be needed to remove a broken rivet
• Match rivet type and length to the original for a secure fit
• Disconnect power and follow all safety precautions before accessing internal parts

This small retainer clip secures components in place to prevent shifting, vibration, or wire movement during appliance operation. Replacing a fatigued or missing clip restores a firm hold and helps eliminate rattles or intermittent connections.

• Holds parts, panels, or wiring securely to their mounting points
• Helps reduce vibration, noise, and wear from loose components
• Common fix when a panel, trim, or harness won't stay attached
• Symptoms can include rattling, loose wiring, or parts popping free

• Unplug the appliance before servicing; shut off water or gas if applicable
• Note original clip orientation and location before removal
• Use needle-nose pliers if needed to compress/position the clip
• Do not overtension; seat fully without deforming mating parts