Wsf263c3exf01 Parts

Replace worn refrigerator door hinge cam bushings to restore smooth door swing and proper alignment. Fixes doors that don't close fully or seal correctly.

Lower front grille that covers the base opening of your refrigerator. Replace if cracked, broken, or missing to restore a finished look.

This bearing nut secures a bearing and related rotating components on the shaft, keeping the assembly tight and aligned for smooth, dependable operation. Replacing a worn or stripped nut helps stop wobble, noise, and drive slippage.

• Locks the bearing/stack onto the shaft to prevent loosening
• Maintains alignment for smooth rotation and reduced vibration
• Helps restore consistent drive in shaft-driven assemblies
• Typical symptoms: loose or non-turning drive, rattling/grinding, or visible thread damage

• Disconnect power before servicing; shut off water if working near dispenser components
• Remove the related assembly to access the shaft; note part order for reassembly
• Hand-start the nut to avoid cross-threading; verify thread direction against the original
• Tighten securely; inspect the bearing, washers/spacers, and shaft for wear

Cracked or missing refrigerator light lens? This cover protects the bulb and diffuses glare in the fresh food section. Simple snap-in installation.

Supports and pivots your refrigerator door for smooth opening and flush closing. Replace if hinge is worn, damaged, or causing misalignment issues.

White refrigerator door hinge for side-by-side models. Replaces worn, cracked, or broken hinges that no longer support the door properly.

Molded plastic drawer for freezer compartment. Replace if cracked, warped, or broken to restore smooth sliding and keep frozen items organized.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

This replacement lid fits the refrigerator utility/bin drawer and restores a secure cover to keep stored items contained and organized. It replaces cracked, broken or warped lids so the bin functions as intended. What it does:

• Covers and protects items stored in the utility/bin drawer
• Replaces lids that are cracked, chipped or no longer latch properly
• Helps prevent items from shifting or falling into other compartments
• Restores a proper seal and alignment of the utility/bin cover

• Unplug or disconnect power to the appliance before servicing for safety
• Remove the bin/drawer per the manufacturer instructions to access the lid
• Align hinge tabs or mounting points and snap or fasten the lid into place
• Handle carefully; plastic edges or mounting points can be fragile during installation

White molded trim pan that restores the lower exterior appearance of your refrigerator. Replaces cracked, warped, or discolored trim pieces.

Fix ice not dispensing properly with this ice crusher blade. Replaces free-wheeling or worn blades on the auger assembly. DIY-friendly repair.

Main wire harness that routes power between the control board and components. Replace if wiring is damaged, burned, or connector clips are broken.

Fix ice that won't crush or dispense with this refrigerator crusher blade. Solves bent or damaged blades preventing ice from dispensing. Easy DIY repair.

Replace your cracked or cloudy dispenser light lens to restore clear illumination. Protects the bulb and improves visibility. Verify fit with your model.

This is a thermostat that monitors the temperature in the ice maker to signal when ice has fully frozen and is ready to be harvested. It acts as a thermal cutoff device to regulate the ice-making cycle. Replace this thermostat if the ice maker stops producing ice, runs continuously without cycling, or fails to eject ice at the proper time.

Door won't close or latch properly? This door cam guides the latch mechanism to restore secure door closure and prevent gaps or misalignment issues.