Wtw5015lw Parts

This washer drive motor is the main component that powers the spin cycle of the appliance. When a washing machine stops spinning or washing, there could be several issues. If the buttons on the control panel are still responsive, most likely it is the drive motor. There could also be a burning smell coming from the washer when the drive motor malfunctions. Using a voltage meter is the only way to show where the problem lies. Unplug the washer and turn off the water supply before starting repairs. Drain all the water from the drain hose into a bucket. Remove the two screws at the base of the front panel, then remove the two screws at the top of the back panel. The top console should be removable at this point, and removing the two screws at the bottom outside corners of the back panel should allow the base to be separated. There are two metal clips attaching the pump to the motor. Unplug the connections from the motor and capacitor. Unscrew the two screws that fasten the motor in, and it should slide out. Reverse these instructions for installation of the new component.This Whirlpool washer drive motor is a genuine OEM replacement part sourced directly from Whirlpool. There are no other parts included with this listing. This part is compatible with Whirlpool and Kenmore appliances.

The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

The Transmission Gearcase is an OEM part for Whirlpool top-load washing machines. It houses the transmission components that control the spin speed via the motor during the extract cycle. Properly functioning gears are essential for removing water through centrifuge action.

Symptoms of a failing Whirlpool transmission gearcase include:

• Inability to spin clothes or reach appropriate RPMs  
• Noisy or grinding sounds from the transmission
• Vibrations felt through the cabinet during spin 

Causes can be worn gears, broken teeth or housing cracks from years of continuous operation. Consistent impacts can accelerate damage over time.

This OEM part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This bleach dispenser for a washing machine holds liquid bleach and releases it into the tub at the appropriate point in the cycle, helping dilute bleach and protect fabrics from contact with undiluted solution. What it does:

• Holds and meters liquid bleach until the machine calls for dispensing
• Helps ensure bleach mixes with water for even, diluted distribution
• Replace if cracked, clogged, or leaking
• Common symptoms include bleach not dispensing, bleach left in the cup, leaks around the dispenser area, or bleach spots on fabrics

• 1 bleach dispenser

• Disconnect power and turn off water before servicing
• Access and mounting vary by model; follow your service manual to reach the dispenser
• Detach hoses/clamps or fasteners, transfer any reusable hardware, and seat the new dispenser fully
• Reconnect, then run a test fill/rinse to check for proper dispensing and leaks

The Lid Lock Bezel (White) is an OEM replacement part for Whirlpool washers. The bezel provides an aesthetic covering for the lid lock mechanism located on top of the washer. 

Causes of a bad bezel can include normal wear and tear from repeated use of the washer lid over time. Scratches, cracks or splits in the plastic material are also possible from accidental impact or drops.

Symptoms of a bad bezel include:

• Cosmetic flaws like discoloration, scratches or cracks that diminish the appearance of the washer
• Looseness, rattling or misalignment of the bezel covering 
• Difficulty opening or closing the washer lid securely. 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

The Tub Ring is an OEM part for Whirlpool washing machines. It is an internal gasket or seal that fits securely around the outer rim of the washer tub. The tub ring works to create a watertight barrier, preventing leakage between the tub and other cabinet components like the agitator shaft or balancer. 

Causes of a bad tub ring can include warping due to heat exposure or tub filling impacts over time, cracks developing from heavy impacts or loads that stress the tub, or cuts and tears caused by debris lodged inside the ring.

Symptoms of a bad tub ring include: 

• Water leaks appearing around the tub or agitator shaft when in use
• Puddles or standing water found inside the washer cabinet 
• Difficulty getting the washer lid or door fully closed and secured
• Excessive moisture buildup inside non-tub areas 

It is also compatible with Maytag, KitchenAid, Amana, Roper, and select Kenmore models.

This leveling foot stabilizes and levels your appliance on uneven floors. It threads into the base so you can raise or lower a corner, reducing rocking and vibration for smoother, quieter operation and proper alignment.

• Provides precise height adjustment to level the cabinet
• Helps prevent wobble, walking, or rattling during use
• Supports stable operation and proper door alignment
• Replaces a missing, stripped, or damaged foot

• Disconnect power; shut off gas/water if applicable
• With help, carefully tilt or brace the appliance to access the foot
• Thread the new foot in by hand, then fine-adjust with a wrench until level and stable
• Ensure all feet contact the floor; recheck level after positioning

This product is a Whirlpool washer main control board sourced directly from the manufacturer. The control board rests behind the main knob assembly of the washer in the console. This component is the main control center for the appliance. Without a properly functioning control board, the washer will not operate efficiently. In cases of a complete shortage of the part, the washer will cease to work completely. Signs of a malfunctioning control board include, but are not limited to, a burning smell coming from the control board, an error message reading from the appliance, or certain functions operating intermittently. Always unplug appliances from their power sources before making any repairs. Use a flathead screwdriver to release the fastening clips located underneath the washing machine's front left and right corners. Pull the panel forward, exposing the main control board area. Unplug the control board from the wiring harnesses, and disconnect the air pressure tube. Finally, remove the small screws that secure the control board assembly. Prepare the new control board assembly for installation and follow these instructions in reverse.This part is a genuine OEM product and is sold individually. This product is compatible with Whirlpool, Crosley, Kenmore, Maytag, and Roper appliances.

This rotary encoder mounts behind the washer's cycle knob and tells the main control which setting you select. When it fails, selections may be erratic or unresponsive. Replacing it restores accurate, dependable cycle selection. What it does

• Detects the position of the cycle selector knob
• Sends selection signals to the main control board
• Enables precise cycle and option changes
• Common symptoms: knob turns but lights don't follow, random/incorrect selection, can't select a cycle, won't start

• One rotary encoder

• Disconnect power to the washer before servicing
• Access the control console and remove the knob/dial to reach the encoder
• Note orientation, unplug the harness, release tabs/screws, and swap in the new encoder
• Handle electronics carefully and avoid static discharge; verify knob-to-light tracking before reassembly

This replacement hose routes liquid or air between internal components, maintaining a secure, leak-resistant path. Replace a brittle, cracked, or clogged hose to prevent leaks and restore proper flow and sensing performance.

• Provides a sealed pathway between components such as the pump, tub, valve, drain path, or pressure system
• Helps maintain correct water flow or pressure/level sensing
• Common symptoms: leaks, kinks/cracks, standing water, slow/failed drain or fill, related error codes
• Restores reliable connections when used with properly seated clamps

• Disconnect power and shut off water supply before servicing; allow hot parts to cool
• Place towels or a shallow pan to catch residual water
• Note routing and clamp locations; transfer or replace clamps as needed and seat the hose fully on fittings
• Test for leaks with a short cycle and re-check all connections

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

This pump drain filter helps protect the appliance's drain pump by screening out debris before it enters the pump. A clean, intact filter supports proper draining and helps prevent clogs and pump damage.

• Screens debris before it reaches the drain pump
• Helps maintain proper draining performance
• May resolve issues like slow or incomplete draining, standing water, or drain-related noises
• Replacing a damaged or missing filter can reduce repeat clogs

• Unplug power and shut off water supply before service
• Access location varies by model; have towels ready for any residual water
• Note orientation of the old filter for correct placement
• After installation, check for leaks and run a brief drain cycle to verify operation

Note: Quantity of 1 pad, order as needed. Measures about 3.5" x 3.5".

This replacement screw secures panels, brackets, and internal components within your appliance. Replacing a missing or damaged fastener restores a tight fit, reduces vibration and noise, and helps keep parts properly aligned during operation.

• Fastens panels, trim, brackets, or internal components to the chassis
• Maintains proper alignment and stability during normal use
• Replaces missing, rusted, or stripped hardware
• Common symptoms: loose or rattling panels, vibration, difficulty fastening, or a visibly missing screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Match length and thread to the original; replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving hole is stripped, repair threads or replace the clip/nut before installing