Wtw8700xw2 Parts

The Hose is an OEM part for Whirlpool washing machines. This hose connects the drain pump to the outer drain hose, allowing water to empty from the washer.

Flexible yet durable, the drain hose withstands pressure during spin cycles without risk of bursting or kinking. Consistent drainage is vital for fully removing water after each cycle.

Causes of a bad hose can include cracks from extended use, mineral or soap buildup restricting flow, or stressed connections that have weakened over time.

Symptoms of a bad drain hose include:

• Incomplete drainage of water at the end of cycles
• Puddles or leaks near the pump or drain area
• Sloshing sounds of retained water inside the machine
• Enlarged hose diameter from constant pressure

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Water Valve and Fill Housing Assembly is an OEM component specifically designed for Whirlpool washing machines. This assembly includes both the water valve and housing that holds it, which work together to control water flow into the washer during operation. 

Over time, the valve and housing can experience wear or become corroded due to chemical exposure, reducing efficiency. 

Symptoms of a bad water valve and fill housing include:

• Slow or improper water fill 
• Leaks or water drips from the valve area
• Abnormal squealing or whining noises
• Inability to select certain water levels

This OEM Whirlpool replacement part is also compatible with KitchenAid, Roper, Estate, Amana, Crosley, and some Kenmore models.

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

A replacement water pump that removes water from the washer during drain cycles, helping restore proper draining and reducing standing water that can prevent the washer from completing drain or spin cycles. What it does:

• Pumps water from the wash tub to the household drain during drain and spin cycles.
• Common symptom: washer won't drain or leaves standing water in the drum.
• Common symptom: pump hums, makes loud/grinding noises, or leaks when the pump is failing or blocked.
• Replacing a worn or damaged pump can resolve drain-related error codes and interrupted cycles.

• Disconnect power and shut off water supply before servicing the appliance.
• Drain excess water and place towels/a shallow pan before removing the old pump to avoid spills.
• Inspect and, if needed, replace associated hoses and clamps to ensure a reliable seal.

Size: .20 Fl. Oz. (6 ml)

Screw: 8-16 x 3/8 inch.

Replace aging or leaking washer supply lines with this fill hose kit. It provides two 5-foot hoses to connect your home's hot and cold water valves to the washer, helping maintain a secure connection and consistent filling.

• Connects hot and cold water faucets to the washer's inlet valves
• Replace if hoses are leaking, cracked, bulging, or kinked
• Can help address slow filling caused by restricted or kinked hoses
• Useful when installing or relocating a washer

• Unplug the washer and shut off both water supply valves before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucet and washer
• Match hot to hot and cold to cold; hand-start threads to avoid cross-threading, then tighten firmly without overtightening
• Restore water and power; run a fill test and check all connections for leaks

This fill hose carries water from the home supply to the appliance inlet valve, restoring proper water fill and helping prevent leaks when the original hose is cracked, worn, or blocked. Ideal for replacing damaged inlet lines. What it does:

• Delivers water from the household supply to the appliance inlet valve for normal fill cycles.
• Replaces cracked, split, or deteriorated hoses that can cause leaks at connections.
• Resolves symptoms such as slow or no water fill, visible leaks, or intermittent filling.
• Durable replacement designed to match OEM routing and connection points.

• Always shut off water supply and disconnect power before starting work.
• Inspect and replace hose clamps or inlet gaskets as needed; ensure proper seating to prevent leaks.
• Hand-tighten fittings and secure clamps—avoid overtightening metal fittings.
• After installation, restore water and power and run a short fill cycle while checking for leaks.

This machine screw secures components in place to maintain proper alignment and stability during appliance operation. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, noise, or loosening parts.

• Provides a secure mechanical fasten for panels, brackets, or internal assemblies
• Helps correct rattling, vibration, or loose-fitting parts
• Useful when an original screw is stripped, corroded, or lost
• Sized to match 8-18 thread applications in compatible units

• Disconnect power and shut off water or gas before servicing
• Note original screw location and orientation for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace any damaged clips or mounts the screw engages

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

5 foot. Package of 2.

Right Side

The Lid Hinge is an OEM part for Whirlpool washers. This hinge connects the washer lid to the cabinet and allows it to safely and securely open and close during operation.

The hinge is responsible for providing a smooth, controlled movement as well as properly securing the lid in place when closed. It ensures proper operation and functionality of the washer by facilitating easy access for loading and unloading clothes.

Causes of a bad hinge can include wear and tear over time, unbalanced loads that put excessive strain on the hinge components, or damage from impact or overextending the lid.

Symptoms of a bad hinge include:

• Difficulty opening or closing the washer lid
• The lid not staying securely closed or popping open during cycles
• Noises or squeaks coming from the hinge area
• The hinge hanging loose or off-track

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This water pump moves and removes water from the appliance so cycles complete and standing water is cleared. Replacing a worn pump restores normal draining and helps prevent leaks and odors. What it does:

• Circulates and pumps water out during drain and pump cycles.
• Stops or reduces operation when the motor or impeller fails, causing no-drain or standing water.
• Can leak if seals or housing crack, leading to water under the appliance.
• May make grinding, humming, or rattling noises when bearings or the impeller are damaged.

• One water pump assembly

• Disconnect power and water supply before starting any repair.
• Inspect hoses and clamps while replacing the pump; replace any damaged components.

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

This factory fastener secures appliance panels and components for a tight, rattle-free fit. Replace a missing, stripped, or corroded screw to keep assemblies aligned and performing as intended.

• Fastens panels, brackets, or assemblies in place
• Helps reduce vibration and rattling caused by loose hardware
• Maintains proper alignment of parts to prevent premature wear
• Common signs you need it: missing screw, loose panel, vibration/buzzing noises, or hardware that won't tighten

• Disconnect power; for gas or water-connected appliances, shut off supply lines before service
• Match the screw to the original; verify size, length, and thread before installation
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug only—do not overtighten, especially into plastic or thin sheet metal

Kit contains two 10 feet inlet hoses.