Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replace your washer drive belt if the drum won't spin or agitate. Connects motor to drum for proper washing cycles. Confirm fit with your model number.
Ordered new transmission, nut, split washer and spanner wrench to do the install. very straight forward fix after watching the video. spanner wrench is a must or the correct large socket with an impact driver. it was corroded on pretty well let the liquid wrench work for a while and then beat it off. approximately 2 hours to do to fix, spent some time cleaning stuff up also though. washer was 12 years old and debated scrapping it and getting a new one but then it would not match the dryer. ... Read more
Secures the timer knob to the shaft for accurate cycle selection. Replace if worn, broken, or lost causing knob to spin freely. Confirm fit with model.
I pulled off the retaining clip with pliers then removed the old knob and timer dial. I replaced all the parts with the new ones and used pliers to reinstall the clip. The teeth on the new knob engage to select the cycle. https://www.youtube.com/watch?v=cQwLtRcHx9k Read more
Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
By GE. Fits many different washer brands and models. Includes insert.
The new GE washers come with a fill valve that has a 1/8" hole for the hot water inlet. This is probably for energy savings or something. So, I installed the older style GE fill valve on my new machine. Since the older style has larger inlet holes for both hot and cold water, it fixed my problem easily. NOTE: The outlet nipple on the new style GE fill valves are larger than the older style. Therefore, I had to make a coupling piece to attach the older style GE valve outlet nipple to the... Read more
Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more
Black. 8-18 AB HXW 3/8
I ordered the part and was impressed to receive it within two day! I didn't need the screws I ordered (which I ordered just in case) but the trim was put on with no problem and my oven looks brand new again! Thank you! Read more
Size: 10-12 a. Includes 12 screws.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
Seals the outer tub to prevent leaks during spin and drain cycles. Replace if washer leaks from the center or bottom. Confirm fit with your model number.
Outer basket had a lot of rust on the lip at the top of the basket, I ordered tub gasket, but when I removed the old gasket, some of the lip broke off, leaving gaps at the top, went to the hardware store, and purchased thin sheet of 8x10" aluminum, cut and shaped pieces from this sheet, to fit under the damaged lip, to bridge the gaps, rounded edges to fit against the rounded part of the outer tub, under the lip, once shaped, I glued them in place with emblem adhesive, did this all the way... Read more
Mounting screw for dryer drum support and internal components. Replaces lost, stripped, or damaged screws during repairs. Package of 12 screws included.
Watched the repair video. Saw what to look for. Found the dryer drum front support was broken and the slide bearings were worn. Replaced these items. Read more
This push button is the user-facing control button that completes a control circuit when pressed, restoring responsiveness to a worn or broken selector interface. It provides a direct, replaceable way to fix unresponsive or stuck control input. What it does
This compressor start relay helps the refrigerator compressor start reliably so the appliance can cool properly. It replaces a failed relay to restore normal compressor startup and reduce hard-start symptoms. What it does:
Protective shield cover that installs inside your washer to guard internal components from heat and debris. Replace if cracked, broken, or missing.
Package of 12
Supports washer drum for smooth, quiet rotation during spin cycles. Replace if you hear grinding noise or excessive vibration. Verify fit with your model.
Cushions and supports the washer leg to reduce vibration and protect flooring. Replace if cracked, worn, or missing to stabilize and level your unit.
I ordered new foot pads and replaced the old ones. Now the washer runs better that it did when it was brand new. Read more
This door gasket seals the refrigerator door to keep cold air in and warm air out, helping maintain proper temperatures and reduce energy use. It replaces a worn, torn, or deformed seal to restore a tight door closure. What it does:
It is an old washing machine that is leaking oil from the transmission, and taking advantage of the disarmament want to change those parts that are damaged.the will rebuild replacing those parts and then paint it. Read more